Power-on password ..........24 Hard-disk password ..........24 Administrator password ........24 Power management ........25 Screen blank state ..........25 Putting the computer to sleep or shutting it down ..............25 Putting your computer to sleep ......25 Shutting down the computer ......26 Lenovo ideapad Y700-14ISK ...... 27 Specifications ..........27 Status indicators ........... 29 Fn key combinations........31 FRU replacement notices ......32 Screw notices ..........32 Removing and replacing an FRU ....33 1010 Base cover ..........34 1020 Battery pack ..........36...
• The product-specific section includes service, reference, and product-specific parts information. Important: This manual is intended only for trained servicers who are familiar with Lenovo products. Use this manual to troubleshoot problems effectively. Before servicing a Lenovo product, make sure to read all the information under “Safety information” on page 1 and “Important service information” on page 16.
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo ideapad Y700-14ISK computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6 • “Safety notices: multilingual translations” on page 7 • “Laser compliance statement” on page 14...
Y700-14ISK Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4. Lift it by standing or pushing up with your leg muscles; this action could avoid the strain from the muscles in your back. Do not attempt to lift any object that weighs more than 16 kg (35 lb) or that you think is too heavy for you. • Do not perform any action that causes hazards to the customer, or that makes the machine unsafe.
About this manual Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges.
Page 8
Y700-14ISK Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. • Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) • If an electrical accident occurs: – Caution: do not become a victim yourself.
The power cord should be the type specified in the parts list. c. Insulation must not be frayed or worn. 4. Check for cracked or bulging batteries. 5. Remove the cover. 6. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 7. Check inside the unit for any obvious unsafe conditions, such as metal filings, contamination, water or other liquids, or signs of fire or smoke damage. 8. Check for worn, frayed, or pinched cables.
Y700-14ISK Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1. Use product-specific ESD procedures when they exceed the requirements noted here.
About this manual Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds.
Page 12
Y700-14ISK Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short- circuit it. Dispose of the battery as required by local ordinances or regulations.
Page 13
About this manual Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
Page 14
Y700-14ISK Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations.
Page 15
About this manual Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à...
Page 16
Y700-14ISK Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
Page 17
About this manual Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Y700-14ISK Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products. Elsewhere, the drive is certified to conform to the requirements of the International Electrotechnical Commission (IEC) 825 and CENELEC EN 60 825 for Class 1 laser products.
Page 19
About this manual A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Strategy for replacing FRUs Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, follow the steps below: 1. Go to http://support.lenovo.com. 2. Enter the serial number or select a product or use Lenovo smart downloading. 3. Select the BIOS/Driver/Applications and download. 4. Follow the directions on the screen and install the necessary software.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one. • If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs one by one to see if the symptoms change. Replace only the FRU that changed the symptoms. Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect.
Note: RoHS and non-RoHS FRU part numbers with the same fit and function are identified with unique FRU part numbers. Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 and 2006 will contain some RoHS compliant FRUs. The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs.
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • Carefully remove screws for reuse when replacing FRUs. • Be extremely careful during such write operations as copying, saving, or formatting. Drives in the computer that you are servicing sequence might have been altered.
Y700-14ISK Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8. Customer’s name and address Note for warranty: During the warranty period, the customer may be responsible for repair costs if the computer damage was caused by misuse, accident, modification, unsuitable physical or operating environment, or improper maintenance by the customer.
• If the computer does not charge during operation, go to “Checking operational charging”. To check the AC adapter, follow the steps below: 1. Unplug the AC adapter cable from the computer. 2. Measure the output voltage at the plug of the AC adapter cable. See the following figure: Note: Output voltage for the AC adapter pin No. 2 may differ from the one you are servicing. 3. If the voltage is not correct, replace the AC adapter. 4. If the voltage is acceptable, do the following: • Replace the system board. • If the problem persists, go to “Lenovo ideapad Y700-14ISK” on page 26. Note: Noise from the AC adapter does not always indicate a defect. Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
Y700-14ISK Hardware Maintenance Manual Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section. Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95% of the total power remains; under this condition the battery pack can charge to 100% of its capacity. This protects the battery pack from being overcharged or from having a shortened life. To check your battery, move your cursor to the Power Meter icon in the icon tray of the Windows® taskbar and wait for a moment (but do not click it), and the percentage of battery power remaining is displayed. To get detailed information about the battery, double-click the Power Meter icon. Note: If the battery pack becomes hot, it may not be able to be charged.
Restoring the factory contents by using OneKey Recovery Restore of factory default The Lenovo ideapad Y700-14ISK computers come with pre-installed OneKey Recovery System. In order to save application files and the initial backed up files of the system, the hard disk in a Lenovo computer includes a hidden partition when it is shipped. If you need to restore the system to the point of your first boot up, just enter Lenovo OneKey Recovery System and run System Recovery. For details of OneKey Recovery System, see the User Guide for Lenovo OneKey Recovery System .
Y700-14ISK Hardware Maintenance Manual Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the administrator password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and shut down. Screen blank state If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing Fn + F2. To end screen blank state and resume normal operation, press any key. Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down.
Y700-14ISK Hardware Maintenance Manual Shutting down the computer If you are not going to use your computer for a long time, shut it down. To shut down your computer, do one of the following: • Move the cursor to the lower-left corner, and then select the Start button. Select Power → Shut down. • Right-click the Start button in the lower-left corner and select Shut down or sign out → Shut down.
This chapter presents the following product-specific service references and product-specific parts information: • “Specifications” on page 27 • “Status indicators” on page 29 • “Fn key combinations” on page 31 • “FRU replacement notices” on page 32 • “Removing and replacing an FRU” on page 33 • “Locations” on page 60 • “Parts list” on page 62 Specifications The following table lists the specifications of the Lenovo ideapad Y700- 14ISK: Table 1. Specifications Feature Description Form Factor Dimensions Appr. 350 mm × 259 mm × 26 mm Weight Appr. 2.2 kg(with 3 cell 45 Wh battery) LCD size 14.0-inch LED...
Page 32
Y700-14ISK Hardware Maintenance Manual Table 1. Specifications (continued) Feature Description I/O Ports USB 3.0 × 2, USB 2.0 × 1 Audio Combo audio jack × 1 Communication RJ-45 × 1 (1000 Mbps) Video/Audio HDMI slot × 1 Memory card slot 4 in 1 slot × 1 (SD/SDHC/SDXC/MMC) Type Li-Polymer Battery pack Cells/Capacity 3 cells, 45 Wh AC power Input 100-240 V, 50-60 Hz AC adapter Output voltage 20 V DC Power 135 W Miscellaneous Camera HD (720 p) Security Kensington lock slot × 1...
Lenovo ideapad Y700-14ISK Status indicators The system status indicators below show the computer status: Table 2. Status indicators Indicator Charge Indicator Meaning status status On (solid white) The computer is powered on. 1 Power Blinking The computer is in sleep mode. The computer is powered off. The battery has more than 80% Charging charge. On (solid white) The battery has more than 20% Discharging charge. The battery has between 5% On (solid amber) Discharging and 20% charge. The battery has between 20% and 80% charge. When the Blinking slowly battery reaches 80% charge, the 2 Battery...
Page 34
Y700-14ISK Hardware Maintenance Manual Table 2. Status indicators (continued) Indicator Charge Indicator Meaning status status 3 Touchpad On (solid white) The touchpad is disabled. The touchpad is enabled. 4 Hard Disk Drive The hard disk drive is reading Blinking orwriting data.
Lenovo ideapad Y700-14ISK Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 3. Fn key combinations Fn + Home: Activate the pause function. Fn + End: Activate the break function. Fn + PgUp: Enable/Disable the scroll lock. Fn + PgDn: Activate the insert function.
Hardware Maintenance Manual FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration. • They are harder to tighten.
Lenovo ideapad Y700-14ISK Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 31. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any of such FRUs are listed at the top of the page. Remove them in the order in which they are listed. 4. Follow the correct sequence in the steps to remove the FRU, as given in the figures by the numbers in square callouts. 5. When turning a screw to replace an FRU, turn it in the direction as given by the arrow in the figure. 6. When removing the FRU, move it in the direction as given by the arrow in the figure.
Y700-14ISK Hardware Maintenance Manual 1010 Base cover Figure 1. Removal steps of base cover Remove the screw 1 and screws 2. Step Screw (quantity) Color Torque M2.0 × 12.5 mm, flat-head, nylok-coated (1) Black 2.0 kgf*cm LOGIC LOWER TO LOGIC UPPER M2.0 × 5.0 mm, flat-head, nylok-coated (10) Black 2.0 kgf*cm LOGIC LOWER TO LOGIC UPPER Remove the base cover in the directions shown by arrows 3 and 4. When installing: Install the screws 2 and then install the screw 1. (Screw 1 is longer than screws 2. )
Page 39
Lenovo ideapad Y700-14ISK Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label: The following labels need to be peeled off from the old base cover and put on the new base cover. GML label Wlan/BT label KR KCC label Indonesia rating label Rating label (73 x 24 mm) Rating label (43 x 24 mm) For some models, you also need to apply one or two FCC labels. Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover. For the location of each label, refer to the following figure:...
Y700-14ISK Hardware Maintenance Manual 1020 Battery pack For access, remove this FRU: • “1010 Base cover” on page 34 DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 2. Removal steps of battery pack Unplug the battery connector in the direction shown by arrow 1, then remove the screws 2.
Page 41
Lenovo ideapad Y700-14ISK Figure 2. Removal steps of battery pack (continued) Remove the battery pack 3.
Y700-14ISK Hardware Maintenance Manual 1030 Hard disk drive For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, suggest the customer to backup all the information on it if possible.
Page 43
Lenovo ideapad Y700-14ISK Figure 3. Removal steps of hard disk drive (continued) Remove the hard disk drive 3. Remove the screws 4 and detach the metal frame from the hard disk drive. Step Screw (quantity) Color Torque M3.0 x 3.0 mm, flat-head, nylok-coated (4) Sliver 2.5 kgf*cm HDD BRK TO HDD Note: The aluminium foil is stuck on HDD. Do not use too much force when remove the aluminium foil, otherwise it might be damaged during disassembly.
• “1020 Battery pack” on page 36 Important: • The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to “Overall” on page 79 for Lenovo part numbers for the approved modules.
Page 45
Lenovo ideapad Y700-14ISK Figure 4. Removal steps of PCI Express Mini Card for wireless LAN (continued) Remove the card in the direction shown by arrow 3. When installing: • In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled MAIN, and the white cable (2nd) (AUX) into the jack labeled AUX on the card. • In models with a wireless LAN card that has three antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, the grey cable (3rd) into the jack labeled 3, and the white cable (2nd) (AUX) into the jack labeled 2 on the card.
Y700-14ISK Hardware Maintenance Manual 1050 DIMM For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 Figure 5. Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the directions shown by arrows 1, and then unplug the DIMM in the direction shown by arrow 2. Note: I f only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( : lower slot), but not in SLOT-1 ( : upper slot). When installing: Insert the notched end of the DIMM into the socket. Push the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed...
Lenovo ideapad Y700-14ISK 1060 LED board For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 Figure 6. Removal steps of LED board Detach the LED board connector in the directions shown by arrows 1 and 2. Remove the screw 3. Then remove the LED board in the direction shown by arrow 4. Step Screw (quantity) Color Torque M2.0 × 3.0 mm, flat-head, nylok-coated (1) Black 2.0 kgf*cm LED Board TO Logic UP...
Y700-14ISK Hardware Maintenance Manual 1070 IO board For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 Figure 7. Removal steps of IO board Detach the connector in the direction shown by arrows 1 and 2. Remove the screw 3.
Page 49
Lenovo ideapad Y700-14ISK Figure 7. Removal steps of IO board (continued) Remove the IO board in the direction shown by arrow 4.
Y700-14ISK Hardware Maintenance Manual 1080 Fan assembly and Heat Sink assembly For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 Figure 8. Removal steps of fan assembly and heat sink assembly Release the antenna cables and the speaker cables from the cable guides 1. Unplug the fan connectors in the direction shown by arrow 2. Remove the...
Page 51
Lenovo ideapad Y700-14ISK Figure 8. Removal steps of fan assembly and heat sink assembly (continued) Remove the fan 4. Remove the screws 5. Step Screw (quantity) Color Torque M2.0 × 6.5 mm, flat-head, nylok-coated (6) Black 2.5 kgf*cm THERMAL(CPU)ASSY TO M/B & THERMAL(GPU)ASSY TO M/B...
Page 52
Y700-14ISK Hardware Maintenance Manual Figure 8. Removal steps of fan assembly and heat sink assembly (continued) Remove the heat sink assembly in the direction shown by arrow 6. When installing: • Route the antenna cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. • Make sure that the connector is attached firmly.
Lenovo ideapad Y700-14ISK 1090 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
Page 54
Y700-14ISK Hardware Maintenance Manual Figure 9. Removal steps of system board (continued) Remove the RJ-45 door and the system board 5. Remove the DC-in cable 6.
Lenovo ideapad Y700-14ISK 1100 Speakers For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 Figure 10. Removal steps of speakers Remove the screws 1. Then remove the speakers in the direction shown by arrows 2. Step Screw (quantity) Color Torque M2.0 × 2.0 mm, flat-head, nylok-coated (2) Black 1.5 kgf*cm...
Y700-14ISK Hardware Maintenance Manual 1110 LCD unit For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 Figure 11. Removal steps of LCD unit Remove the screws 1. Step Screw (quantity)
Page 57
Lenovo ideapad Y700-14ISK Figure 11. Removal steps of LCD unit (continued) Open the hinge in the direction shown by arrows 2. Remove the upper case in the direction shown by arrow 3.
Y700-14ISK Hardware Maintenance Manual 1120 LCD front bezel For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 • “1110 LCD unit” on page 52 Figure 12. Removal steps of LCD front bezel...
Lenovo ideapad Y700-14ISK 1130 LCD panel and LCD cable For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 • “1110 LCD unit” on page 52 • “1120 LCD front bezel” on page 54 Figure 13. LCD panel and LCD cable Remove four screws 1.
Page 60
Y700-14ISK Hardware Maintenance Manual Figure 13. Removal steps of LCD panel and LCD cable (continued) Turn over the LCD module. Peel off the adhesive tape and detach the connector in the direction shown by arrow 1. Then remove the LCD panel. When installing: Make sure that the metal connector is attached firmly.
Lenovo ideapad Y700-14ISK 1140 LCD hinges For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 • “1110 LCD unit” on page 52 • “1120 LCD front bezel” on page 54 • “1130 LCD panel and LCD cable” on page 55 Figure 14. Removal steps of hinges Remove screws 1. Remove the hinges in the direction shown by arrows 2...
Y700-14ISK Hardware Maintenance Manual 1150 Camera For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 • “1110 LCD unit” on page 52 • “1120 LCD front bezel” on page 54 • “1130 LCD panel and LCD cable” on page 55 • “1140 LCD hinges” on page 57 Figure 15. Removal steps of camera...
Lenovo ideapad Y700-14ISK 1160 Antenna assembly For access, remove these FRUs in order: • “1010 Base cover” on page 34 • “1020 Battery pack” on page 36 • “1030 Hard disk drive” on page 38 • “1040 PCI Express Mini Card for wireless LAN” on page 40 • “1050 DIMM” on page 42 • “1060 LED board” on page 43 • “1070 IO board” on page 44 • “1080 Fan assembly and Heat Sink assembly” on page 46 • “1090 System board” on page 49 • “1100 Speakers” on page 51 • “1110 LCD unit” on page 52 • “1120 LCD front bezel” on page 54 • “1130 LCD panel and LCD cable” on page 55 • “1140 LCD hinges” on page 57 • “1150 Camera” on page 58 Figure 16. Removal steps of antenna assembly...
Y700-14ISK Hardware Maintenance Manual Locations Front view and right-side view 1 Integrated camera (on select models) 2 Built-in microphones (with noise reduction) 3 Wireless LAN antennas 4 Computer display 5 JBL speakers 6 Power button 7 Touch pad 8 Kensington lock slot 9 RJ-45 port J HDMI port K USB 3.0 port L Memory card slot Note: For the description of each indicator, see “Status indicators” on page 29.
Y700-14ISK Hardware Maintenance Manual Parts list This section presents the following service parts: • “Overall” on page 63 • “LCD FRUs” on page 67 • “Miscellaneous parts” on page 69 • “AC adapters” on page 70 • “Screws” on page 70 • “Power cords” on page 71 Note: Each FRU is available for all types or models, unless specific types or models are specified. Attention: Do not attempt to replace an FRU on your own. If an FRU is damaged, contact a Lenovo authorized servicer or a marketing representative for replacement...
Page 68
Y700-14ISK Hardware Maintenance Manual Table 4. Parts list—Overall No. FRU FRU no. CRU ID. See “Miscellaneous parts” on page 69. LCD unit (see “LCD FRUs” on page 67.) Upper Case C 80NU W/KB US BKL 5CB0K44756 Upper Case C 80NU W/KB GK BKL 5CB0K44703 Upper Case C 80NU W/KB INT'E BKL 5CB0K44776 Upper Case C 80NU W/KB KR BKL 5CB0K44778 Upper Case C 80NU W/KB CH BKL 5CB0K44750 Upper Case C 80NU W/KB RU BKL 5CB0K44747 Upper Case C 80NU W/KB AR-E BKL 5CB0K44743 Upper Case C 80NU W/KB HE BKL 5CB0K44775 Upper Case C 80NU W/KB TH BKL 5CB0K44785 Upper Case C 80NU W/KB INDIA BKL 5CB0K44732 Upper Case C 80NU W/KB UK BKL 5CB0K44772 Upper Case C 80NU W/KB IT BKL...
Page 69
Lenovo ideapad Y700-14ISK Table 4. Parts list—Overall (continued) No. FRU FRU no. CRU ID. Upper Case C 80NU W/KB LA NBKL 5CB0K44718 Upper Case C 80NU W/KB CF-E NBKL 5CB0K44709 Upper Case C 80NU W/KB ND NBKL 5CB0K44762 Upper Case C 80NU W/KB FR NBKL 5CB0K44755 Upper Case C 80NU W/KB GR NBKL 5CB0K44711 Upper Case C 80NU W/KB BZ NBKL 5CB0K44712 Upper Case C 80NU W/KB DUTCH NBKL 5CB0K44699 Upper Case C 80NU W/KB HG NBKL 5CB0K44768 Upper Case C 80NU W/KB BE NBKL 5CB0K44751 Upper Case C 80NU W/KB ICE NBKL 5CB0K44701 Upper Case C 80NU W/KB SL NBKL 5CB0K44765 Upper Case C 80NU W/KB SW NBKL 5CB0K44715 Upper Case C 80NU W/KB CZ-SK NBKL 5CB0K44783...
Lenovo ideapad Y700-14ISK LCD FRUs In Lenovo Y700-14 ISK, there are following types of LCDs. • “14.0-in. HD LED”...
Page 72
Y700-14ISK Hardware Maintenance Manual Table 5. Parts list—14.0-in. HD LED No. FRU FRU no. CRU ID. LCD Bezel C 80NU W/Magnet 5B30K44721 Panel, LGD LP140WF6-SPB1 FHD AG S NB 5D10H34771 Panel, LTN140HL05-401 FHD AG S NB 5D 5D10H29268 Panel, NV140FHM-N41 FHD AG S NB 5D10H32288 Hinge C 80NU L+R 5H50K44735 EDP Cable C 80NU 5C10K44780 Camera C 80NU HD 5C20K44736 Camera, BIS BNC416YTK HD NB camera 5C20G89272 Camera, AVC HAA-6D0F03 HD NB camera 5C20G89276 Camera, CCY CNFEH39 HD NB camera 5C20G89264 LCD Cover C 80NU W/Antenna 5CB0K44749...
Lenovo ideapad Y700-14ISK Miscellaneous parts Table 6. Parts list—Miscellaneous parts FRU no. CRU ID. System miscellaneous parts: • a RJ45 Door C 80NU HDD 5D30K44781 • b HDD Bracket C 80NU W/Mylar 5B40K44714 • c W lan Bracket C 80NU 5B40K61147 Cable miscellaneous parts: • d DC-IN Cable C 80NU 5C10K44771 • e H DD Cable C 80NU 5C10K44730 • Note: Italicized letters in parentheses are references...
Lenovo ideapad Y700-14ISK Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region: Table 9. Parts list—3-pin power cords Region CRU ID. 145000593 • LINETEK LP-61L+ H03VV-F+ LS15 1m 145000561 • Longwell LP-61L+H03VV-F+LS-18 1m 145000605 • VOLEX MP5004+H03VV-F+VAC5S 1m 145500000 • lux 0031+H03VV-F 0.75/3C+0011 1m Europe 145000585 • LINETEK LP-34+H03VV-F + LS15 1m Europe 145000553 • Longwell LP-34A+H03VV-F+LS-18 1m Europe 145000525 • VOLEX M2511+HO3VV-F+VAC5S 1m...
Page 76
Y700-14ISK Hardware Maintenance Manual Table 9. Parts list—3-pin power cords (continued) Region CRU ID. Japan 145000530 • VOLEX VAC5S+VCTF+M755 1m Japan 145500005 • lux 0018(E)+VCTF 0.75/3C+0021 1m Australia 145000589 • LINETEK LS15+H03VV-F+LP-23A 1m Australia 145000557 • Longwell LP-23A+LFC-3R+LS-18 1m Australia 145000532 • VOLEX AU10S3+H03VV-F+VAC5S 1m Australia 145500006 • lux 0038+H03VV-F 0.75/3C+0011 1m Taiwan 145000588 • LINETEK LS15+VCTF+LP-53 1m...
Page 77
Lenovo ideapad Y700-14ISK Table 9. Parts list—3-pin power cords (continued) Region CRU ID. Brazil 145000564 • Longwell LP-46+H03VV-F+LS-18 1m Brazil 145000527 • VOLEX CH10S3+H03VV-F+VAC5S 1m Brazil 145500011 • lux 0034+H03VV-F 0.75/3C+0011 1m Israel 145000595 • LINETEK LS15+H03VV-F+LP-41 1m Israel 145000563 • Longwell LP-41+H03VV-F+LS-18 1m Israel 145000526 • VOLEX SI16S3+H03VV-F+VAC5S 1m Israel 145500012 • lux 0041+H03VV-F 0.75/3C+0011 1m...
Y700-14ISK Hardware Maintenance Manual Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any Lenovo intellectual property right may be used instead. However, it is the...
Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Trademarks The following terms are trademarks or registered trademarks of Lenovo in the United States, other countries, or both. Lenovo OneKey Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, products, or service names may be trademarks or service...