(shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. DEH-P5950IB/XN/ES...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-P5950IB/XN/ES...
• Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 2.1 PACKING DEH-P5950IB/XN/ES...
Page 9
XHP7016 ••••• Protector XHP7017 Accessory Assy CEA6708 Case Assy XXA7417 Polyethylene Bag CEG1160 (2) CONTRAST TABLE DEH-P5950IB/XN/ES , DEH-P5950IB/XN/ES1 and DEH-P5990IB/XN/ID are constructed the same except for the following: Mark Description DEH-P5950IB/XN/ES DEH-P5950IB/XN/ES1 DEH-P5990IB/XN/ID Owner's Manual XRD7120 XRD7120 XRB7044 Owner's Manual...
Page 11
FM/AM Tuner Unit CWE1952 Screw BPZ20P080FTB IC(IC301) PAL007C Button XAC7149 Button(1-6) XAC7148 Button(BAND,DISP) XAC7146 Sub Spring Assy XXA7363 Spring XBH7001 Cover XNS7180 Lighting Conductor XNV7033 Connector(CN1901) CKS5207 Button(UP,DOWN,L,R) XAC7147 Double side Tape CNM8673 OLED Unit MXS8233 Holder XNC7028 Holder XNV7034 DEH-P5950IB/XN/ES...
Page 12
(2) CONTRAST TABLE DEH-P5950IB/XN/ES , DEH-P5950IB/XN/ES1 and DEH-P5990IB/XN/ID are constructed the same except for the following: Mark Description DEH-P5950IB/XN/ES DEH-P5950IB/XN/ES DEH-P5990IB/XN/ID Detachable Assy XXA7478 XXA7478 XXA7530 Sub Grille Assy XXA7485 XXA7485 XXA7531 Grille Unit XXA7466 XXA7466 * XXA7529 Panel Unit...
Detailed page IPBUS:2.2 dBs AUX/IPOD : 2.2 dBs CN701 PANEL UNIT CD:0 dBs DEH-P5950IB/XN/ES DEH-P5950IB/XN/ES1 DEH-P5990IB/XN/ID NOTE : Symbol indicates a resistor. For resistors and capacitors in the circuit diagrams, their resistance values or No differentiation is made between chip resistors and capacitance values are expressed in codes: discrete resistors.
Page 19
> DETACH FM,AM:21.1 dBs IPBUS:36.3 dBs CD:36.1 dBs AUX/IPOD:35.3 dBs The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. DEH-P5950IB/XN/ES...
Page 33
4LOEJ 312SNS 5 V/div 5 V/div 1 V/div 4LOEJ 0FIN 5 V/div 1 V/div Black dot(800 μm) during play 12 cm CD Eject operation 8 cm CD Eject operation Ref.: Ref.: Ref.: REFO Mode: Mode: Mode: Normal Normal Normal DEH-P5950IB/XN/ES...
For further information for respective destinations, be sure to check with the schematic dia- CORD ASSY gram. 2.Viewpoint of PCB diagrams AUX INPUT IP-BUS Capacitor Connector SIDE A SIDE B Chip Part P.C.Board CN701 DETACH DEH-P5950IB/XN/ES...
Page 35
SIDE A REAR OUTPUT FRONT OUTPUT SUBWOOFER OUTPUT ANTENNA iPOD TESTIN CN1950 FRONT DEH-P5950IB/XN/ES...
4.4 CD CORE UNIT(S10.5COMP2) CD CORE UNIT(S10.5COMP2) SIDE A CN651 PICKUP UNIT(P10.5)(SERVICE) LOADING /CARRIAGE MOTOR SPINDLE MOTOR DEH-P5950IB/XN/ES...
Page 41
CD CORE UNIT(S10.5COMP2) SIDE B DEH-P5950IB/XN/ES...
D 852 (B,48,16) Diode RB411D IC 704 (A,125,59) IC NJM2794V D 853 (A,22,27) Diode MTZJA10(B) IC 851 (B,38,18) IC NJM2360M D 901 (A,71,110) Diode MPG06G-6415G3 IC 901 (A,5,120) IC NJM2388F84 Q 101 (B,42,105) Transistor 2SA1576A D 902 (A,74,110) Diode MPG06G-6415G3 DEH-P5950IB/XN/ES...
Page 43
R 216 (B,90,85) RS1/16S101J R 649 (B,70,32) RS1/16S104J R 217 (A,79,88) RS1/16S101J R 651 (A,16,60) RD1/4PU561J R 218 (B,79,94) RS1/16S101J R 653 (A,70,28) RS1/16S221J R 301 (A,145,84) RS1/16S103J R 654 (A,72,30) RS1/16S104J R 302 (A,131,99) RS1/16S331J R 666 (B,81,39) RS1/16S104J DEH-P5950IB/XN/ES...
Page 44
C 218 (A,76,94) CEJQ100M25 R 825 (A,112,20) RS1/16S0R0J C 219 (A,83,94) CEJQ100M25 R 831 (B,93,27) RS1/16S473J C 220 (A,56,90) CEJQ470M16 R 832 (B,94,24) RS1/16S102J C 242 (B,66,95) CKSRYB104K16 R 833 (B,100,20) RS1/16S222J C 243 (A,69,93) CEJQ470M16 R 850 (A,26,35) RD1/4PU681J DEH-P5950IB/XN/ES...
Page 45
S 1974 (A,5,38) Push Switch CSG1155 C 822 (A,81,14) CKSRYB473K50 S 1975 (A,7,20) Push Switch CSG1155 C 833 (B,99,25) CKSRYB105K10 S 1976 (A,40,71) Push Switch CSG1155 S 1977 (A,40,82) Push Switch CSG1155 C 852 (B,37,25) CKSRYB223K50 C 854 (B,45,12) CCSRCH331J50 DEH-P5950IB/XN/ES...
Page 46
(A,40,100) LED CL-195SR-CD R 1984 (B,33,117) RS1/16S182J R 1985 (B,33,120) RS1/16S332J D 1949 (A,40,110) LED CL-195SR-CD R 1986 (B,35,122) RS1/16S472J D 1950 (A,40,121) LED CL-195SR-CD D 1951 (A,40,132) LED CL-195SR-CD R 1987 (B,32,135) RS1/16S822J D 1952 (A,40,146) LED CL-195SR-CD DEH-P5950IB/XN/ES...
Page 47
R 1956 (B,30,35) RS1/16S101J X 201 (A,23,35) Ceramic Resonator 16.934 MHz CSS1603 R 1959 (B,36,35) RS1/16S151J S 901 (A,53,37) Switch(HOME) CSN1067 R 1962 (B,36,33) RS1/16S151J S 903 (B,19,58) Switch(DSCSNS) CSN1067 R 1965 (B,27,157) RS1/16S181J S 904 (B,38,67) Switch(12EJ) CSN1068 DEH-P5950IB/XN/ES...
Page 48
C 206 (A,22,39) CKSSYB104K10 C 207 (A,24,37) CKSRYB104K16 C 209 (B,33,40) CEVW220M6R3 C 210 (B,29,42) CKSSYB104K10 C 211 (A,27,34) CKSSYB104K10 C 212 (B,29,32) CKSRYB104K16 C 213 (A,44,37) CKSSYB104K10 C 214 (A,28,33) CKSSYB104K10 C 216 (A,50,51) CKSSYB332K50 C 217 (A,46,51) CKSSYB104K10 DEH-P5950IB/XN/ES...
1 k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-P5950IB/XN/ES...
Page 50
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. DEH-P5950IB/XN/ES...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-P5950IB/XN/ES...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. DEH-P5950IB/XN/ES...
[Features of this test mode] Enables switching at any time to the iPod source Disables communication with iPod Disables indication of logos (Pioneer) on iPod Functions regardless of connection of the iPod body to H/U [How to shift to test mode] The following describes how to enter and display the test mode.
The frequency of the clock signal is 625 kHz that is one 32th of the fundamental frequency(20 MHz/32). The clock signal should be 625 kHz(±25 Hz). If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. DEH-P5950IB/XN/ES...
Remove the two screws and then remove the Grille Assy. Fig.1 Grille Assy Removing the Tuner Amp Unit (Fig.2) Remove the screw. Remove the three screws. Straighten the tabs at three locations indicated and then remove the Tuner Amp Unit. Tuner Amp Unit Fig.2 DEH-P5950IB/XN/ES...
Page 57
Upper Frame. 3. While lifting the Carriage Mechanism, remove it from the three Dampers. Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. Damper Damper Carriage Mechanism Lower Frame DEH-P5950IB/XN/ES...
Page 58
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw. Poly Washer Change Arm Pickup Lock Arm Inner Holder Feed Screw Planet Gear Pickup Rack Chassis Pickup DEH-P5950IB/XN/ES...
Page 63
EVOL : Source select(iPod) IPODON Not used 53-59 Power supply input(+) Not used Communication mode (UART) notification output psensg Connection sense input Power supply control output PPOWER psens Connection sense input DALMON For consumption current reduction output Not used DEH-P5950IB/XN/ES...
Page 65
OELD master clock output MCLK AD KEY input 2 ADKEY2 AD reference voltage input(VCC) VREF AD KEY input 1,0 17,18 ADKEY1,0 General purpose port(DIMMER output) Command select for OELD controller XCMD PEG268A Format Meaning CMOS PE5547A Format Meaning CMOS Nch open drain DEH-P5950IB/XN/ES...
Page 66
Power supply for the crystal oscillator Power supply for DAC DA.VDD Output of audio for the left channel LOUT Ground for DAC DA.GND Connected to the capacitor for band gap REGC DA.GND Ground for DAC Output of audio for the right channel ROUT DEH-P5950IB/XN/ES...
Page 67
Output of reference voltage REFOUT Reversal input of FE Output of FE ADCIN FE,TE A/D converter input Reversal input of TE Output of TE Output of LD Input of PD AD.VDD Power supply for servo ADC Ground for servo ADC AD.GND DEH-P5950IB/XN/ES...
Page 68
22 AUDIOGND audio ground Ground of audio block 23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output DEH-P5950IB/XN/ES...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 300 msec, the oscillator may be defective. Source ON SYSPW←H Pin 1 Completes power-on operation. (After that, proceed to each source operation.) DEH-P5950IB/XN/ES...
Page 74
CD Mechanism Module Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 g p p DEH-P5950IB/XN/ES...