Filling The Fuel Tank With Gasoline; Adjusting The Cutting Height; Starting The Engine - Toro 22295 Operator's Manual
21in heavy-duty recycler/rear bagger lawn mower
Hide thumbs
Also See for 22295:
- Operator's manual (32 pages) ,
- Installation instructions manual (13 pages) ,
- Service bulletin (3 pages)
Table of Contents
Advertisement
If the oil level is below the lower-limit mark, add oil. Refer to
3 Filling the Crankcase with Oil (page
Filling the Fuel Tank with
Gasoline
DANGER
Gasoline is extremely flammable and explosive. A
fire or explosion from gasoline can burn you and
others.
• To prevent a static charge from igniting the
gasoline, place the container and/or machine
directly on the ground before filling, not in a
vehicle or on an object.
• Fill the tank outdoors when the engine is cold.
Wipe up spills.
• Do not handle gasoline when smoking or around
an open flame or sparks.
• Store gasoline in an approved fuel container, out
of the reach of children.
•
For best results, use only clean, fresh (less than 30 days
old), unleaded gasoline with an octane rating of 87 or
higher ((R+M)/2 rating method).
•
Oxygenated fuel with up to 10% ethanol or 15% MTBE
by volume is acceptable.
•
Ethanol: Gasoline with up to 10% ethanol (gasohol)
or 15% MTBE (methyl tertiary butyl ether) by volume
is acceptable. Ethanol and MTBE are not the same.
Gasoline with 15% ethanol (E15) by volume is not
approved for use. Never use gasoline that contains
more than 10% ethanol by volume, such as E15
(contains 15% ethanol), E20 (contains 20% ethanol), or
E85 (contains up to 85% ethanol). Using unapproved
gasoline may cause performance problems and/or engine
damage which may not be covered under warranty.
•
Do not use gasoline containing methanol.
•
Do not store fuel either in the fuel tank or in fuel
containers over the winter unless you use fuel stabilizer.
•
Do not add oil to gasoline.
Important: To reduce starting problems, add fuel
stabilizer to the fuel all season, mixing it with gasoline
less than 30 days old.
Note: The capacity of the fuel tank is 3.8 L (1.0 US gallon).
Adjusting the Cutting Height
You can change the cutting height at each wheel by adjusting
a cutting-height lever. Cutting heights are 25 mm (1 inch), 38
mm (1-1/2 inches), 51 mm (2 inches), 64 mm (2-1/2 inches),
76 mm (3 inches), 89 mm (3-1/2 inches), 102 mm (4 inches),
114 mm (4-1/2 inches).
9).
12
DANGER
Adjusting the cutting-height levers could bring your
hands into contact with a moving blade and result
in serious injury.
• Shut off the engine and wait for all movement to
stop before adjusting the cutting height.
• Do not put your fingers under the housing when
adjusting the cutting height.
1. Pull the cutting-height lever toward the wheel
14) and move the lever to the desired setting.
Figure 14
1. Rear cutting-height lever (2)
2. Front cutting-height lever (2)
2. Release the cutting-height lever and seat it securely in
the notch.
3. Adjust all the wheels to the same cutting-height setting.
Starting the Engine
1. Connect the spark-plug wire to the spark plug.
2. Open the fuel valve by moving the fuel-valve lever to
the right
(Figure
15).
Figure 15
1. Fuel-valve lever
3. Move the throttle-control lever to the C
(Figure
16).
(Figure
position
HOKE
Hide quick links:
Advertisement
Table of Contents
