Table of Contents
Advertisement
3.6
VARIOUS OPERATIONS AND FUNCTIONS
(Cont'd)
An
example
of ameliorated NC
program by
the above
operations
is shown
below.
<Program before FS
edit>
<
Program
after FS edit/
0100:
0100;
G28 X10. Y10. Z10.;
G92 X100. Y100.
Z100.;
.
GOO G90
FI
00.;
.
.
M03S3000;
G01 X200.;
Y200. F80.
S3300;
G28 X10. Y10.
Z10.;
G92 X100.
Y100:
Z100.;
GOO G90 FJ00.;-
M03-S3000;
G01
X200.;
Y200.;
—
.....
FSED MEM is closed
with override
80%,
.
and S overried
110%
M"
X500.;-
-
Override
60%
.
S override
100%
X500. F60.
S3000:
M30;
M30;
NOTE
1. When FSED MEM
('FS
memory)
is closed more than 2 times in one
block,
the F and
S
values
obtained when FSED
MEM closed
last time are
stored. The
count
of- FSED MEM is
not
increased
in
this case.
-
-.
>
2. When FSED MEM
(FS
memory)
closes
during
execution
of
sub
program.
The
F
and
S
values.
are reflected
in the sub
program.
Therefore, pay
attention when
the
sub
program
is called from
other
program.
3. When FSED CH
(FS
memory change)'
is closed. CYCLE START
is
invalid.
4. When FSED MEM
(FS
memory)
is
closed,
CYCLE. START
is
invalid.
5.
During
TAP CYCLE
operation.
FSED MEM
(FS memory)
is invalid.
6.
.
When FSED MEM
(FS memory)
closes during
RAPID TRAVERSE
operation, only
S
value is
stored.
7. Closing FSED
MEM
(FS
memory)
more than 128 times causes a
warning
alarm and no more
.
data are stored.
•
8.
When FSED M
(FS
edit
mode)
closes
during
memory
operation.
FSED.S
(in
FS edit
mode)
is
not
closed.
j
9. When FSED
M
closes
during
automatic
operation or
manual operation. FS edit mode is
not
entered. A
message
"FSED MODE INVLD"
displayed.
10. When
FSED MEM closes
during interruption
of
memory operation
(SINGLE
BLOCK
slop,
FEED
HOLD), a message
"CAN'T STORE FS!"
is displayed
and the F and S values are
not
stored.
11. When FSED CH closes
during memory operation,
a
message
"CAN'T CHANGE FS!"
is dis¬
played
and the
memory
is
not
validated.
12. When FSED CLR closes
during
FS
memory
validation
(FS
memory
change)
,
a
message
"CAN'
T CLEAR FS!" is displayed and the data
are
not
cleared.
13. The
following edit operations can
not
be performed
in FS edit mode. EDIT LOCK takes offects.
Insert.
Change,
Delete, Copy,
Move.
Replace,
O-number
Copy.
O-number
Rename,
and O-numbr
Delete.
14.
When FS edit mode is entered with FSED M closed
during editing on operation
screen,
the edit
job
is
released.
15. Closing
FSED CH
while the tool lenght
measurement
screen and work-
preset
screen are
displayed,
the screen is
not
switched
to
the
opration screen.
A
message
"FSED ERR!" is dis¬
played.
-
632
-
Advertisement
Table of Contents
