Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Harbor Freight Tools Central Machinery 61487
Summary of Contents for Harbor Freight Tools Central Machinery 61487
-
Page 2: Table Of Contents
Table of contents Safety ............3 Maintenance ..........15 Specifications ..........6 Parts List and Diagram ......18 Setup ............6 Warranty ............ 20 Operation ........... 11 WARNING SyMBOLS AND DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. -
Page 3: Safety
IMpORTANT SAFETy INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. KEEP GUARDS IN PLACE and in working order. 11. -
Page 4: Drill Press Safety Warnings
Grounding Instructions TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT GROUNDING WIRE cONNEcTION READ AND FOLLOW THESE INSTRUcTIONS: 110-120 V~ Grounded Tools: Tools with Three prong plugs 1. In the event of a malfunction or breakdown, 6. Repair or replace damaged or grounding provides a path of least resistance for worn cord immediately. -
Page 5: Vibration Safety
If unreadable or missing, contact designed to filter out microscopic particles. Harbor Freight Tools for a replacement. (California Health & Safety Code § 25249.5, et seq.) 13. Avoid unintentional starting. 16. WARNING: Handling the cord on this product will Prepare to begin work before turning on the tool. -
Page 6: Specifications
Specifications Motor 120VAC, 60Hz, 13.5A 220, 290, 360, 430, 500, 570, 640, 730, 810, 900, Spindle Speeds 1460, 1730, 1820, 2380, 2650, 3600 RPM Spindle Stroke 2-3/4" Spindle Taper Chuck Capacity 7/64" to 5/8" (3mm to 16mm) Swing 17″ Table Diameter 12-7/8″... - Page 7 Table to column 1. Lubricate the Worm Gear (45) teeth with light grease 6. While holding the Rack and the Table Support and insert the Gear shaft-first into the Table Support as assembled, slide both down onto the Column. (46). Extend the shaft as far as possible through the Slide the Rack down until the bottom of the Rack opening in the side of the Support.
- Page 8 Head Assembly to column See Figure c. 1. Before installing the Head Assembly, it may be Belt Tension necessary to back the four Socket Head Cap Lever (96) Screws (6) out slightly to ensure they do not protrude internally, as this would prevent the Belt Tension Head Assembly from sliding fully into position.
-
Page 9: Installing The Chuck
Installing the Belts 1. Undo the Belt Tension Locking Knobs (87) on IMpORTANT: Tension is correct when the belts both sides of the Head. Turn the Belt Tension deflect by approximately 1/2″ at their centers of Lever (97) clockwise to bring the Motor Pulley run when using reasonable thumb pressure. - Page 10 Functions Page 10 For technical questions, please call 1-800-444-3353. Item 61487...
-
Page 11: Operation
Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. - Page 12 changing Drill Speed 4. Consult Figure F (or the chart inside the See Functions on page 10 for illustrations. Pulley Cover) and install the Belts on the 1. WARNING! TO pREVENT SERIOUS Pulleys in the positions that correspond INJURy: Turn off and unplug the Drill to the required Spindle/Drill speed.
- Page 13 Using the cutting Oil Drip System 1. Remove the upper Oil Bottle from the Oil 4. Open the Oil Pipe valve and adjust the Pipe Bottle Clips and unscrew the Cap. so the oil drips onto the cutting area. 2. Make sure that the Oil Pipe valve is closed. 5.
-
Page 14: General Operating Instructions
Workpiece and Work Area Set Up 1. Designate a work area that is clean and well-lit. 9. FOR FLAT WORK, lay the workpiece on The work area must not allow access by children a wooden base and clamp it down firmly or pets to prevent distraction and injury. -
Page 15: Maintenance
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. - Page 16 Adjusting the Spindle Feed Handle Return Torsion Spring This procedure must be performed only by a qualified technician. Wear a full face shield during this procedure. If the Spindle does not return all the way up or moves up 7. Turn the screwdriver counterclockwise and sluggishly, or if it requires too much force to pull down engage the next Spring Cap notch.
-
Page 17: Troubleshooting
Troubleshooting problem possible causes Likely Solutions Tool will 1. Cord not connected. 1. Check that cord is plugged in. not start. 2. No power at outlet. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. -
Page 18: Parts List And Diagram
parts List and Diagram parts List part Description part Description Base Rubber Ring Column Support Ball Bearing 6004 Flat Washer 10 Retainer Ring 19 Spring Washer 10 Retainer Ring 47 Bolt M10×35 Ball Bearing 6205 Socket Head Cap Screw M10×10 Bearing Spacer Ring Column Spindle Housing... - Page 19 Assembly Diagram 93 94 101 102 103 78 79 22 21 Item 61487 For technical questions, please call 1-800-444-3353. Page 19...
-
Page 20: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.