hit counter script
Download Print this page
Ecco ED37777 Series Installation And Operation Instructions Manual

Ecco ED37777 Series Installation And Operation Instructions Manual

Led directionals

Advertisement

Quick Links

WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property
damage, serious injury, and/or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the safety informa-
tion contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are
essential to ensure the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he
can operate the system without losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air
bag deployment area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal
injury or death. Refer to the vehicle owner's manual for the air bag deployment area. It is the responsibility of the user/
operator to determine a suitable mounting location ensuring the safety of all passengers inside the vehicle particularly
avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use,
the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open
trunks or compartment doors), people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an inter-
section, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying
all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and
regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
SPECIFICATIONS
Size:
4.3"L x 0.9"W x 1.4"H
Weight:
0.3 lbs.
Voltage Range:
12-24VDC
Current draw at 12.8VDC:
ED3777X:
1.3A Max.
ED37777XX: 1.4A Max.
Prior to installation:
Carefully remove the unit from its packaging. If damage is found, contact the transit company or ECCO. Do not use broken or
damaged parts. Prior to mounting, consideration should be given to cable location.
Installation and Operation Instructions
ED3777 Series LED Directionals
Power Consumption at 12.8 VDC:
ED3777X:
ED3777XX: 16.9W Max.
Temperature Range:
Flash Rate:
15.6W Max.
-22° to 122°F
-30° to 50°C
See Flash Pattern Charts
Page 1 of 6

Advertisement

loading

Summary of Contents for Ecco ED37777 Series

  • Page 1 See Flash Pattern Charts Prior to installation: Carefully remove the unit from its packaging. If damage is found, contact the transit company or ECCO. Do not use broken or damaged parts. Prior to mounting, consideration should be given to cable location.
  • Page 2: Mounting Instructions

    Mounting Instructions: Caution: When drilling into any vehicle surface, make sure the area is free from any electrical wires, fuel lines, vehicle upholstery, etc. that could be damaged 1. Select a flat mounting surface with the visibility of the flash and ease of wiring access taken into consideration.
  • Page 3 Wiring Instructions: Important! This unit is a safety device and it must be connected to its own separate, fused power point to assure its continued operation should any other electrical accessory fail. Wire as shown in FIGURE 1. All wiring should be a minimum of 20 AWG. The positive line must have a slow blow 3 amp fuse. Routing the ground wire directly back to negative battery terminal is recommended.
  • Page 4 Synchronization: The directional is capable of syncing with other compatible ECCO products by setting the desired flash pattern on each unit individually. It is also strongly recommended that the same rate and style of flash pattern be used on all synced units to produce the most effective warning pattern.
  • Page 5 ED3777XX Flash Pattern Chart White SAE J595 CA T13 SAE J845 ECE R65 Red and Description Sync Phase Wire Wire White Wires A (110°) B (100°) ) ° W (90°) 1-Default 1-Default Single Flash - Color 1 Class 1 Class1 Class 1 Class1 Class B Class B Class B Class 1 Class1 Class 1 Class1 Single Flash - Color 1 Class 1 Class 1 Class 1 Class 1 Class B Class b Class B Class 1 Class 1 Class 1 Class 1 Single Flash - Split - Color 1 Then 2...
  • Page 6: Exclusion Of Other Warranties

    Manufacturer Limited Warranty and Limitation of Liability: Manufacturer warrants that on the date of purchase, this product will conform to Manufacturer’s specifications for this product (which are available from the Manufacturer upon request). This Limited Warranty extends for Thirty-Six (36) months from the date of purchase. DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR OTHER HAZARD;...
  • Page 7 Instrucciones de Instalación y Operación ED3777 Luz de Advertencia ¡ADVERTENCIA! En caso de no instalar ni utilizar este producto conforme a las sugerencias del fabricante se podrían ocasionar daños a la propiedad, lesiones graves personales o el deceso del usuario y de las personas que se busca proteger. No instale u opere este producto de seguridad a menos que haya leído y comprendido la información de seguridad que contiene este manual.
  • Page 8 Ensamblaje: Ensamblaje en la superficie Ensamblaje adhesivo Superficie de MOUNTING ensamblaje SURFACE Superficie de MOUNTING ensamblaje SURFACE Ensamblaje en el borde Ensamblaje permanente Alambre: ED3777 ROJO: Positivo (se necesita añadir un fusible 2A) Cable: ED3777XX NEGRO: Negativo AZUL: Conmutación de patrones ROJO: Positivo, Colores 1 y 3 (se necesita añadir un fusible 5A) AMARILLO: Función sincronizada BLANCO: Positivo, Colores 2 y 4 (se necesita añadir un fusible 5A)
  • Page 9: Detección Y Resolución De Problemas

    DETECCIÓN Y RESOLUCIÓN DE PROBLEMAS Las series ED3777 y ED3777XX han sido probadas y aprobadas en fábrica. Si las funciones o el dispositivo fallan, revise lo siguiente: Luego de conectarse al suministro de energía, asegúrese de que el extremo de la fuente de energía esté conectado de forma correcta.
  • Page 10 Instructions d'installation et d'utilisation ED3777 Éclairage d'avertissement AVERTISSEMENT! Le non-respect des recommandations d’installation ou d’utilisation du fabricant peut entraîner des matériels, de graves blessures et/ou votre mort et celle de ceux que vous cherchez à protéger! N’installez et/ou n’utilisez ce produit de sécurité que si vous avez lu et compris les informations de sécurité contenues dans ce manuel.
  • Page 11: Montage

    Montage : Montage en surface Fixation adhésive Surface de MOUNTING montage SURFACE Surface de MOUNTING montage SURFACE Montage permanent Montage de bord Câblage : ED3777 ROUGE : Positif (besoin d’ajouter un fusible 2A) Câblage : ED3777XX NOIR : Négatif ROUGE : Positif, couleurs 1 et 3 (besoin d’ajouter un fusible 5A) BLEU : Commutation de configuration BLANC : Positif, couleurs 2 et 4 (besoin d’ajouter un fusible 5A) JAUNE : Fonction synchronisée...
  • Page 12 DÉPANNAGE Les appareils séries ED3777 et ED3777XX ont été testés en usine et approuvés. Si les fonctions de l'appareil tombent en panne, veuillez vérifier les points suivants : Après avoir branché l’appareil, assurez-vous que la source d'alimentation est jointe correctement. Ensuite, assurez-vous qu’aucun court-circuit ne se produise.

This manual is also suitable for:

Ed3777 series