Advertisement
Quick Links
Connections/Installation
Connections
WARNING
• Use speakers over 50 W (output value)
and between 4 Ω to 8 Ω (impedance
value). Do not use 1 Ω to 3 Ω speakers for
this unit.
• The black cable is ground. When
installing this unit or power amp (sold
separately), make sure to connect the
ground wire first. Ensure that the ground
wire is properly connected to metal parts
of the car's body. The ground wire of the
power amp and the one of this unit or
any other device must be connected to
the car separately with different screws. If
the screw for the ground wire loosens or
falls out, it could result in fire, generation
of smoke or malfunction.
Ground wire
POWER AMP
Other devices
Metal parts of
(Another electronic device
car's body
in the car)
*1 Not supplied for this unit
Important
• When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect the
red cable to the terminal that detects
operation of the ignition key may result
in battery drain.
ACC position
No ACC position
• Use this unit with a 12-volt battery and
negative grounding only. Failure to do so
may result in a fire or malfunction.
• To prevent a short-circuit, overheating or
malfunction, be sure to follow the
directions below.
– Disconnect the negative terminal of the
battery before installation.
– Secure the wiring with cable clamps or
adhesive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
– Place all cables away from moving parts,
such as the shift lever and seat rails.
– Place all cables away from hot places,
such as near the heater outlet.
– Do not connect the yellow cable to the
battery by passing it through the hole
to the engine compartment.
– Cover any disconnected cable
connectors with insulating tape.
– Do not shorten any cables.
– Never cut the insulation of the power
cable of this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
– Use a fuse of the rating prescribed.
– Never wire the negative speaker cable
directly to ground.
– Never band together negative cables of
multiple speakers.
• When this unit is on, control signals are
sent through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or the
vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
• Never connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so
may result in battery drain or a
malfunction.
This unit
FH-X820BS
Microphone (4 m)
SiriusXM Connect Vehicle Tuner input
Power cord input
Microphone input
Rear output
Front output
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
Subwoofer output
SiriusXM Connect Vehicle Tuner (sold
separately)
FH-X720BT/X721BT
Power cord input
Microphone input
Microphone (4 m)
Rear output or subwoofer output
Front output
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
FH-X520UI
Power cord input
Rear output or subwoofer output
Front output
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can
be connected (sold separately).
Power cord
Perform these connections when not
connecting a rear speaker lead to a
subwoofer.
En
19
Advertisement
Related Manuals for Pioneer FH-X720BT
Summary of Contents for Pioneer FH-X720BT
- Page 1 FH-X720BT/X721BT Connections/Installation connect it to the antenna booster power supply terminal. • Never connect the blue/white cable to Connections the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna.
- Page 2 Do not connect anything to the green if it overheats. Install this unit away from and green/black leads. hot places such as near the heater outlet. Not used. FH-X720BT/X721BT/X520UI • Optimum performance is Subwoofer (4 Ω) × 2 obtained when the unit is Orange/white installed at an angle of less Connect to a car’s illumination signal.
- Page 3 Install the microphone on the rear side DIN Rear-mount To install on the sun visor of the steering column. Determine the appropriate position Fit the microphone lead into the where the holes on the bracket and groove. the side of the unit match. Microphone lead Groove Tighten the screws on each side.
- Page 4 CD player Bluetooth Specifications System: Compact disc audio system (FH-X820BS/X720BT/X721BT) Usable discs: Compact disc Version: Bluetooth 3.0 certified General Signal-to-noise ratio: 94 dB (1 kHz) (IHF-A Output power: +4 dBm Maximum (Power Power source: 14.4 V DC (10.8 V to 15.1 V network) class 2) allowable)