Page 15
SENS-:> i c COARSE-:> i -r-·�', t , t l t::. riJ �iiil.lllJrfH· OPENn· /:., CLOSE i c'· O) �l/4 ifflxJf1 E [c'· ;il/iJ � L, IRISL.,H- (RCP-730) &. &. ;t.21Jiill/J�liT i-to IRIS::>a;J, (RCP-731) OPENn· G CLOSE* -r-· 0) 1,:�ll,1#1 H[l;Hfa'[-r-· .ll, t!1 l i -t CLOSE1P!JO) ·F�Ui rs!:5:l: l i To...
Page 19
Table of Contents For the customers in the USA WARNING :::s Overview ............... 2(E) Location and Function of Parts ......3(E) ;;;· This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of Front Panel ............
Page 20
MSU-700 master black adjustments. Master Setup Unit. For the iris and master black adjustments, the RCP-730 uses a joystick type control while the RCP-731 uses Four units mountable on a 19-inch rack rotary knobs.
Location and Function of Parts E) Camera/CCU function ON/OFF buttons Control select block Various functions of the video camera or the CCU- 700A/700AP can be turned on and off from this panel. The functions except KNEE OFF, DTL OFF, GAMMA OFF, and CHROMA OFF are ON when the respective buttons are lit.
Page 23
Filter control block OFF ➔ ON (page 1) ➔ ON (page 2) ➔ · · · ➔ ON (page n) The contents of the self-diagnosis may be displayed when required even if this button is not lit. ECS/Shutter control block ®...
Page 24
Location and Function of Parts (i) MONITOR SELECT buttons G) Power and output signal select block Press to select the output signal from the WF 1 OUTPUT connector of the CCU-700A/700AP. The □□□ signal corresponding to the lit button is output. SEQ (sequential): When this button is pressed, you can monitor the waveforms of the three R, G, and B signals in sequence on a monitor connected to the...
Page 25
AUTO SETUP block MASTER GAIN buttons and display window Select the appropriate video gain according to the illumination of the subject to be shot. The selected value (dB) is displayed in the window. The gain value increases when the .A (up) button is pressed and decreases when the T (down) button is pressed.
Page 26
Location and Function of Parts Paint control block WHITE (white balance adjustment) For R, G, and B white level adjustments. □□□□���ww��□□□□□ □ �□□□□□�□□□□□�□□ CLEAR BLACK (black balance adjustment) For R, G, and B black level adjustments. □□□□��w����□□□□□ □□□□□□□ □�□□□□□�□□□□□�□□ □□□□□□□ WHITE BLACK GAMMA FLARE KNEE I KNEE...
Page 27
MONO COLOR (mono color adjustments) KNEE SLOPE (Knee slope adjustments) For R, G, B knee slope adjustments. For adjustments of the saturation and hue of the chroma signal to be mixed with the mono color □□�����□�w���� □ □ function. □□□□□ □...
Page 28
Location and Function of Parts Iris/master black control block (RCP-730) CLOSE button AUTO button EXT indicator 00000000 [!][!] 00000000 00000000 IRIS/MB ACTIVE button 00000000 00000000 00000000 CLOSE AUTO 00000000 f-number display---+----� 00000000 RELATIVE button __ ,...___.__ RELATIVE SENS control knob...
Page 29
Relative mode Absolute mode (RELATIVE button lit) (RELATIVE button not lit) IRIS lever (RCP-730) Adjusts the iris with relative values within 1 /4 of Adjusts the iris within the variable range set by IRIS control (RCP-731) the total range from OPEN to CLOSED.
Page 30
Acljusling ttie LCD DisplaJ Specilicalians General The RCP-730/731 is provided with LCD-display adjustment mode, which permits you to adjust the Power requirements 10 to 30 V brightness and contrast of the LCD display of the paint Power consumption 4 W max.
Page 31
· · · ' :. i Le materiel contenu dans ce manuel consiste en.\ . . . informations qui sont la propriete de Sony Ce>r po i'�ti01:r et sont destinees exclusivement rusagedes ac:qu�reurs. de . ·. • . ' ] l'equipement decrit dans ce manuel.