Dell Force10 S4810P Configuration Manual page 634
High-density, 1ru 48-port 10gbe switch
Hide thumbs
Also See for Force10 S4810P:
- Manual (60 pages) ,
- Quick start manual (27 pages) ,
- Reference manual (1637 pages)
Table of Contents
Advertisement
Figure 29-7. CLI for Configuring Redundant Layer 2 Pairs without Spanning Tree
FTOS(conf-if-range-gi-3/41-42)#switchport backup interface GigabitEthernet 3/42
FTOS(conf-if-range-gi-3/41-42)#show config
!
interface GigabitEthernet 3/41
no ip address
switchport
switchport backup interface GigabitEthernet 3/42
no shutdown
!
interface GigabitEthernet 3/42
no ip address
switchport
no shutdown
FTOS(conf-if-range-gi-3/41-42)#
FTOS(conf-if-range-gi-3/41-42)#do show ip int brief | find 3/41
GigabitEthernet 3/41
GigabitEthernet 3/42
[output omitted]
FTOS(conf-if-range-gi-3/41-42)#interface gig 3/41
FTOS(conf-if-gi-3/41)#shutdown
00:24:53: %RPM0-P:CP %IFMGR-5-ASTATE_DN: Changed interface Admin state to down: Gi 3/41
FTOS(conf-if-gi-3/41)#00:24:55: %RPM0-P:CP %IFMGR-5-OSTATE_DN: Changed interface state to
down: Gi 3/41
00:24:55: %RPM0-P:CP %IFMGR-5-INACTIVE: Changed Vlan interface state to inactive: Vl 1
00:24:55: %RPM0-P:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Gi 3/42
00:24:55: %RPM0-P:CP %IFMGR-5-ACTIVE: Changed Vlan interface state to active: Vl 1
00:24:55: %RPM0-P:CP %IFMGR-5-STATE_STBY_ACT: Changed interface state from standby to active:
Gi 3/42
FTOS(conf-if-gi-3/41)#do show ip int brief | find 3/41
GigabitEthernet 3/41
GigabitEthernet 3/42
[output omitted]
Figure 29-8. CLI for Redundant Pair in Port-channel on S4810
FTOS#show interfaces port-channel brief
Codes: L - LACP Port-channel
LAG
Mode
Status
1
L2
up
2
L2
up
FTOS#configure
FTOS(conf)#interface port-channel 1
FTOS(conf-if-po-1)#switchport backup interface port-channel 2
Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Po 2
Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 2
Apr 9 00:15:13: %STKUNIT0-M:CP %IFMGR-5-STATE_ACT_STBY: Changed interface state to standby: Po 2
FTOS(conf-if-po-1)#
FTOS#
FTOS#show interfaces switchport backup
Interface
Port-channel 1
Port-channel 2
FTOS#
FTOS(conf-if-po-1)#switchport backup interface tengigabitethernet 0/2
Apr 9 00:16:29: %STKUNIT0-M:CP %IFMGR-5-L2BKUP_WARN: Do not run any Layer2 protocols on Po 1 and Te 0/2
FTOS(conf-if-po-1)#
634
|
Layer 2
unassigned
unassigned
unassigned
unassigned
Uptime
Ports
00:08:33
Te 0/0
00:00:02
Te 0/1
Status
Paired Interface
Active
Port-chato mannel 2
Standby
Port-channel 1
YES Manual up
NO
Manual up
NO
Manual administratively down down
YES Manual up
(Up)
(Up)
Status
Standby
Active
up
down
up
Advertisement
Table of Contents
Troubleshooting
