Nokia X7-00 Service Manual

Hide thumbs Also See for X7-00:

Guía del usuario (128 pages)

User manual (128 pages)

User manual (120 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Nokia X7-00

Page 1 Up to 6 hours Up to 450 hours WCDMA: WCDMA: Up to 4.5 hours Up to 450 hours Note: Talk times are dependent on network parameters and phone settings Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 2: Table Of Contents
DISASSEMBLY INSTRUCTIONS ............................12 10. ASSEMBLY INSTRUCTIONS ............................... 22 11. ASSEMBLY WITH THE SS-252 JIG INSTRUCTIONS ....................... 34 12. RESETTING A SHORT-CIRCUITED X7-00 ........................47 13. SOLDER COMPONENTS ..............................48 Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 3 Approved 12.04.2011 The purpose of this document is to help NOKIA service levels 1 and 2 workshop technicians to carry out service to NOKIA products. This Service Manual is to be used only by authorized NOKIA service suppliers, and the content of it is confidential. Please note that NOKIA provides also other guidance documents (e.g.
Page 4: Copyright
Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.
Page 5: Warnings And Cautions
3. Use only approved components as specified in the parts list. 4. Ensure all components, modules screws and insulators are correctly re–fitted after servicing and alignment. 5. Ensure all cables and wires are repositioned correctly Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 6: Esd Protection
RM-707 / RM-659 Service Manual Level 1&2 3. ESD PROTECTION Nokia requires that service points have sufficient ESD protection (against static electricity) when servicing the phone. Any product of which the covers are removed must be handled with ESD protection. The SIM card can be replaced without ESD protection if the product is otherwise ready for use.
Page 8: Battery Information
Batteries’ performance is particularly limited in temperatures well below freezing. Do not dispose batteries in a fire! Dispose of batteries according to local regulations (e.g. recycling). Do not dispose as household waste. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 9: Exlpoded View
CAMERA KEY (I0029 - I0032) I0029 VOLUME KEY B-COVER I0030 I0032 AV JACK I0031 Only available Not reuseable Repair/swap Ver. 1.0 as assembly after removal only in level 3 Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 10: Service Devices
For more information, refer to the Service Bulletin (SB-011) on Nokia SS-252 Assembly Jig Online. Supplier or manufacturer contacts for tool re-order can be found in “Recommended service equipment” document on Nokia Online. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 11: Software Update
To use the FLS-5 Flash Dongle, follow the user guide inside the sales package. Please check always for the latest version of flash software, which is available on Nokia Online. Confidential | Copyright © 2011 Nokia | All rights reserved...
Page 12: Disassembly Instructions
TRAY. 5) Pull out and remove the MICRO SD TRAY. 6) Push from the shown place to open the SIM TRAY. Pull out and remove the SIM TRAY. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 13 Unscrew the two Torx+ size 4 screws in the order 11) Unscrew the two Torx+ size 4 screws in the order shown. Do not use them again. Discard them. shown. Do not use them again. Discard them. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 14 17) Lift slightly up the top end of the A-COVER TOUCH with the SRT-6. Be careful not to damage the ASSEMBLY. Be careful not to damage the TOUCH FLEX connector. connector. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 15 Do not use it again. Discard it. ASSEMBLY with the protective film. 22) Protect the DIPRO LED with the protective film to 23) Protect the DISPLAY with the protective film. avoid short circuit. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 16 28) Release the DISPLAY CONNECTOR RETENTION CLIP 29) Remove the DISPLAY CONNECTOR RETENTION CLIP with the dental tool from the shown place. with the tweezers. Do not use it again. Discard it. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 17 Do not use them again. Discard them. order shown. Do not use them again. Discard them. 34) Protect the VOLUME KEY with the protective film. 35) Protect the CAMERA KEY with the protective film. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 18 39) Turn the device over and remove the B-COVER. shown place. 40) Remove the BATTERY. 41) Remove the IHF BB SHIELD. Do not use it again. Discard it. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 20 51) Remove the EARPIECE ADHESIVE with dental tool. use it again. Discard it. Do not use it again. Discard it. 52) Remove the MICRO USB BOOT. 53) Remove the CAMERA KEY with the tweezers. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 21 Service Manual Level 1&2 54) Remove the VOLUME KEY with the tweezers. 55) Remove the AV JACK. 56) The Nokia X7-00 disassembly is now complete. -END OF DISASSEMBLY- Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 22: Assembly Instructions
5) Place the EARPIECE ADHESIVE with the tweezers. 6) Place the EARPIECE with the tweezers. Note the Press it gently with the SS-93 to active the adhesive. alignment of the EARPIECE. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 23 12) Peel off the DISPLAY CONDUCTIVE ADHESIVE place the second IHF SPEAKER MESH and second the protective film. IHF SPEAKER. Be careful not to touch the highlighted area! Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 24 17) To ensure that the VOLUME KEY and the CAMERA 18) Remove the CAMERA opening protective film with KEY stays in place, be sure to use the protective film the tweezers. as shown. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 25 ENGINE BOARD by using the two shown guiding pins. 23) Place the IHF BB SHIELD and align it using the 24) Place the BATTERY. three shown holes. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 26 BOTTOM END CAP and the MAIN CHASSIS ASSEMBLY. Tighten the two shown TORX+ size 4 screws to the torque of 25 Ncm in the order shown. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 27 35) Turn the DISPLAY over on to the MAIN CHASSIS. 36) Activate the adhesive by gently pressing the DISPLAY for 5 seconds from the top, middle and bottom as shown. Be careful not to damage the DISPLAY. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 28 A-COVER TOUCH ASSEMBLY. The protective film. MENU / HOME KEY should be located on the center. Press the MENU / HOME KEY for 3 seconds to activate the adhesive. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 29 48) Tighten these two TORX+ size 4 screws to the second SIDE LOCKING PIN. torque of 10 Ncm in the order shown. Press the B- COVER down while tightening these screws. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 30 Please refer to the gap specification document for while fastening the next two screws. Tighten these accurate values. two TORX+ size 4 screws to the torque of 10 Ncm in the order shown. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 31 59) Place the BOTTOM END FACE PLATE to the BOTTOM 60) Peel out the AV FACE PLATE adhesive protective END CAP and press it gently for 5 seconds to activate film. the adhesive. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 32 5 seconds to activate the adhesive. 65) Remove the BOTTOM END CAP and the CAMERA 66) Remove the VOLUME KEY and the TOP END CAP KEY protective films. protective films. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 33 Nokia X7-00 / X7-00.1 RM-707 / RM-659 Service Manual Level 1&2 67) Remove the B-COVER and the CAMERA protective 68) Now the Nokia X7-00 assembly procedure is films. complete. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 34: Assembly With The Ss-252 Jig Instructions
5) Place the EARPIECE ADHESIVE with the tweezers. 6) Place the EARPIECE with the tweezers. Note the Press it gently with the SS-93 to active the adhesive. alignment of the EARPIECE. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 35 12) Peel off the DISPLAY CONDUCTIVE ADHESIVE place the second IHF SPEAKER MESH and second the protective film. IHF SPEAKER. Be careful not to touch the highlighted area! Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 36 17) To ensure that the VOLUME KEY and the CAMERA 18) Remove the CAMERA opening protective film with KEY stays in place, be sure to use the protective film the tweezers. as shown. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 37 23) Connect the HSJ FLEX connector with the SS-93. 24) Place the IHF BB SHIELD and align it using the Be careful not to damage the connector. three shown holes. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 38 28) Open the jig as shown. Be sure to open also the shown end of the jig. 29) Place the device in the jig by using the two 30) Lock the bottom end of the jig. shown guiding pins. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 39 10 Ncm in the order shown. 35) Adjust the top part of the jig as shown. 36) Use the SS-93 to connect the DISPLAY CONNECTOR. Be careful not to damage the connector. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 40 41) Unlock and open the jig and remove the device 42) Remove the DIPRO LED protective film. from it. Check the shown gaps for defects in installation. Please refer to the gap specification document for accurate values. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 41 Start placing the A- COVER TOUCH ASSEMBLY to its place from the shown side. Note that the A-COVER TOUCH ASSEMBLY has to be assembled in a slight angle. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 42 10 Ncm in the order shown. Press the B- Then press the AV FRONT SEAL to its place with finger COVER down while tightening these screws. and make sure it is aligned correctly. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 43 Then close the top part of the upwards. Tighten these two TORX+ size 4 screws to jig and lock it. the torque of 10 Ncm in the order shown. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 44 65) Peel out the BOTTOM END FACE PLATE adhesive 66) Place the BOTTOM END FACE PLATE to the BOTTOM protective film. END CAP and press it gently for 5 seconds to activate the adhesive. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 45 5 seconds to activate the adhesive. 71) Insert the SIM TRAY and the MICRO SD TRAY. 72) Remove the BOTTOM END CAP and the CAMERA KEY protective films. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 46 73) Remove the VOLUME KEY and the TOP END CAP 74) Remove the B-COVER and the CAMERA protective protective films. films. 75) Now the Nokia X7-00 assembly procedure is complete. Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...
Page 47: Resetting A Short-Circuited X7-00
Service Manual Level 1&2 12. RESETTING A SHORT-CIRCUITED X7-00 Nokia X7-00 is susceptible to shorting of the VBAT line during display assembly due to exposed VBAT at the Dipro IR LED. This results in the battery protection circuit opening. The following instructions will close the battery protection circuit.
Page 48: Solder Components
13. SOLDER COMPONENTS Solder components S2700 X1650 X2402 X2065 X2066 X2401 X6310 X2701 X2704 X2707 X2702 X2063 X2064 X2703 X2700 BOTTOM F3300 X2100 X2502 X6301 X6302 X1502 X1500 Ver. 1.0 Confidential | Copyright © 2011 Nokia | All rights reserved Version 1.0...

This manual is also suitable for:

X7-00.1

Nokia X7-00 Service Manual

Quick Links

Related Manuals for Nokia X7-00

Summary of Contents for Nokia X7-00

This manual is also suitable for:

Table of Contents