Sony VPL-FE100U Protocol Manual
Lcd data projector
Hide thumbs
Also See for VPL-FE100U:
- Operating instructions manual (120 pages) ,
- Quick start reference sheet (6 pages)
Related Manuals for Sony VPL-FE100U
Summary of Contents for Sony VPL-FE100U
- Page 1 PROTOCOL MANUAL For General Release MODEL ......DEST. VPL-FE100U US/CND VPL-FE100E VPL-FE100M VERSION 1.0 Projector Firmware ARC32 LCD DATA PROJECTOR...
- Page 2 COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS POUR LA SÉCURITÉ DU FONCTIONNEMENT. NE LES APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS REMPLACER QUE PAR DES COMPOSANTS SONY DONT LE PUBLISHED BY SONY. NUMÉRO DE PIÈCE EST INDIQUÉ DANS LE PRÉSENT...
-
Page 3: Table Of Contents
5-3. BASIC OPERATIONS ..................6 CONNECTION ................6-1. RS-232C CONNECTION ................. 7 6-2. RS-422A CONNECTION ................. 7 6-3. PJ COM CONNECTION .................. 8 6-4. CONNECTION EXAMPLE ................8 COMMUNICATION PROCEDURE ..........COMMUNICATION RULES ............APPROXIMATE RETURN WAITING TIMES ......10. COMMANDS ................VPL-FE100U/FE100E/FE100M... -
Page 5: Introduction
Section 10 “COMMANDS”. Using an external CONTROLLER or SWITCHER, etc., inputs can be switched and the power can also be turned on and off. In the following paragraphs, “CONTROLLER” means an external device such as a PC which controls projector using these commands. VPL-FE100U/FE100E/FE100M... -
Page 6: Communication Specifications
. Half duplex (4-wire) PROJECTOR dedicated communication channels . Start/stop system bit serial word serial digital signal . Baud rate: 38.4 k, 19.2 k, 9600 bps (bits per second) . Refer to “2-1. RS-232C Communication Signal” for details on the bit configuration. VPL-FE100U/FE100E/FE100M... -
Page 7: Command Block Format
B15 *128 + B16 Check Data Length Data Length Bn = B (16 + 1) Data (n) Data (n + 1,2,3,4...) Bm = B (16 + Total Data Length) Data B (m + 1) Check SUM B (m + 2) End Code VPL-FE100U/FE100E/FE100M... -
Page 8: Data Of Code
02 – 81 Note : Error when 82 to FF hex codes are included. 4 Data Size (*1) Data Length 2 00 – 10 (B15 *80 hex) Data Size Note : Error when 11 to FF hex codes are included. VPL-FE100U/FE100E/FE100M... - Page 9 10100101 (165) 10100101 (165) Answer 00000000 When 0XA5 (165) and 0X5A (90) are calculated by XOR ; Answer 10100101 (165) 01011010 (90) Answer 11111111 (255) 8 End Condition B (m + 2) END Code No Data in some cases VPL-FE100U/FE100E/FE100M...
-
Page 10: Basic Operations
PJ COM again. Basic operations at PJ COM are the same. The data input to the unit once is checked that there are no errors, and is transmitted to RS-232C/422A again. The unit serves as a communication bridge. VPL-FE100U/FE100E/FE100M... -
Page 11: Connection
Conversion tool Connector : 9 Pin D-subminiature female (D-9S) If CONTROLLER is wired with RS-232C and PROJECTOR is with RS-422A, the following connection is recommended. CONTROLLER PROJECTOR Controller Projector or Switcher signal RX DA MAX202E MAX489 TX DA ECSD MAX232E VPL-FE100U/FE100E/FE100M... -
Page 12: Pj Com Connection
System consisting of two SWITCHERs and two PROJECTORs. Projector Controller No.1 PJ COM RS-232C Projector In T Switcher No.2 RS-422A No.1 Switcher No.2 Connect CONTROLLER to the RS-232C Port of the nearest unit. Connect PROJECTOR and SWITCHER using the PJ COM Port. VPL-FE100U/FE100E/FE100M... -
Page 13: Communication Procedure
In some cases, CONTROLLER may receive data from DEVICE even though it has not sent a command. (For example, during SYS setting, SIRCS command, and switcher information when switcher is selected.) Note : When All (00 hex) is specified for the INDEX No., return data may not be returned in some cases. VPL-FE100U/FE100E/FE100M... -
Page 14: Communication Rules
(value) will not be incorporated. . When INDEX specified SIRCS direct command (CMD1 = 17 hex) is transmitted, leave an interval of 45 mSec until the next transmission. (Do not return the return data (ACK, NAK) when the SIRCS direct command is received.) VPL-FE100U/FE100E/FE100M... -
Page 15: Approximate Return Waiting Times
APPROXIMATE RETURN WAITING TIMES CMD2 (hex) TIME (mSec) Note : The times shown in this table are when communication is performed one to one between CONTROLLER and DEVICE, and in the condition that it will not be interrupted by some reason. VPL-FE100U/FE100E/FE100M... - Page 16 VPL-FE100U/FE100E/FE100M...
-
Page 17: Commands
DATA #1 DATA #2 INPUT CHANNEL CHANNEL PC-3000 00 VIDEO 11–18 SW'ER1-1–8 01 S VIDEO 21–28 SW'ER2-1–8 02 INPUT A 31–38 SW'ER3-1–8 03 INPUT B 41–48 SW'ER4-1–8 04 INPUT C 51–58 SW'ER5-1–8 05 PC-3000 61–68 SW'ER6-1–8 71–78 SW'ER7-1–8 81–88 SW'ER8-1–8 VPL-FE100U/FE100E/FE100M... - Page 18 SPEAKER SETTING SENSE PC ← PROJ RETURN DATA SPEAKER 00 ON 01 OFF PC → PROJ OSD LANGUAGE SETTING SENSE PC ← PROJ RETURN DATA OSD LANGUAGE 00 ENGLISH 01 FRENCH 02 GERMAN 03 ITALIAN 04 SPANISH 05 JAPANESE 06 CHINESE VPL-FE100U/FE100E/FE100M...
- Page 19 02 NO INPUT 02 POS/NEG/- 03 NEG/POS/- 04 NEG/NEG/- 05 CPOS/-/- 06 NPOS/-/- 07 -/-/SonG PC → PROJ SOFTWARE VER. SENSE PC ← PROJ RETURN DATA DATA #1 DATA #2 DATA #3 DATA #4 MAIN MCU ROM VERSION DATA VPL-FE100U/FE100E/FE100M...
- Page 20 02 INPUT A 03 INPUT B 04 INPUT C XX (PC-3000 Channel is selectable only by SIRCS format command) PC → PROJ COLOR SYS SETTING SELECT COLOR SYS 00 AUTO 01 NTSC 02 PAL 03 SECAM 04 NTSC443 05 PALM VPL-FE100U/FE100E/FE100M...
- Page 21 01 ON PC → PROJ INPUT A SETTING SELECT INPUT A 20 COMPUTER 30 COMPONENT 40 DTV-YPBPR 41 DTV-GBR PC → PROJ INPUT B SETTING SELECT INPUT B 10 VIDEO 11 SVIDEO 20 COMPUTER 30 COMPONENT 40 DTV-YPBPR 41 DTV-GBR VPL-FE100U/FE100E/FE100M...
- Page 22 DATA #1 DATA #2 DATA #3 PC ← PROJ REUTRN DATA GAIN R GAIN G GAIN B PC → PROJ BIAS DATA READ DATA #1 DATA #2 DATA#3 PC ← PROJ REUTRN DATA BIAS R BIAS G BIAS B VPL-FE100U/FE100E/FE100M...
- Page 23 DATA #1 DATA #2 DATA #3 GAIN R GAIN G GAIN B PC ® PROJ BIAS DATA WRITE DATA #1 DATA #2 DATA #3 BIAS R BIAS G BIAS B PC ® PROJ MEMORY TRIGGER ITEM 00 WHITE BALANCE VPL-FE100U/FE100E/FE100M...
- Page 24 GP INDEX GP INDEX 1 GP INDEX 2 GP INDEX 3 GP INDEX 4 GP INDEX 5 GP INDEX 6 GP INDEX 7 GP INDEX 8 GP INDEX 9 0 (ALL) DPT PHASE LENS ZOOM LENS SHIFT LENS FOCUS VPL-FE100U/FE100E/FE100M...
- Page 25 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.