hit counter script
Sanyo VCC-4312P Instruction Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Security Camera
  5. VCC-4312P
  6. Instruction manual
Sanyo VCC-4312P Instruction Manual

Sanyo VCC-4312P Instruction Manual

Hide thumbs Also See for VCC-4312P:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG
MANUEL D'INSTRUCTIONS
COLOUR CCD camera
CCD-Farbkamera
Caméra CCD COULEUR
CCD
About this manual
Before installing and using the camera, please read this
manual carefully. Be sure to keep it handy for later reference.
Über diese Bedienungsanleitung
Lesen Sie bitte vor der Montage und dem Inbetriebnehmen der
Kamera zuerst diese Bedienungsanleitung sorgfältig durch und
bewahren Sie sie zum späteren Nachschlagen auf.
A propos de ce manuel
Avant d'installer et d'utiliser la caméra, veuillez lire ce
manuel attentivement. Gardez-le à portée de main
pour toute référence ultérieure.
VCC-4312P

Advertisement

Table of Contents
loading

Related Manuals for Sanyo VCC-4312P

Summary of Contents for Sanyo VCC-4312P

  • Page 1: Instruction Manual

    INSTRUCTION MANUAL VCC-4312P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS COLOUR CCD camera CCD-Farbkamera Caméra CCD COULEUR About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully. Be sure to keep it handy for later reference.

  • Page 2: Table Of Contents

    Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • The optical filter is switched automatically to colour image or black CONTENTS and white image according to the subject brightness.

  • Page 3: Precautions

    Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.

  • Page 4: Parts Names

    PARTS NAMES Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. Flange-back adjustment lever (See page 6) Flange-back lock screw Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately).
  • Page 5 PARTS NAMES Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS").
  • Page 6 PARTS NAMES Power indicator (POWER) Comes on when the power to the camera is on. Video output connector (VIDEO OUT: BNC type) NC + – Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. External sync composite video signal input connector (VBS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor.
  • Page 7 PARTS NAMES Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below.

  • Page 8: Mounting The Lens

    MOUNTING THE LENS Check the lens mount Do not use a lens if the length “ ” is more than mm. That may damage the camera and prevent proper installation. Installation of a DC type auto-iris lens (sold separately) A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power source. This camera can receive (the A.I.
  • Page 9 Video output (1.0 Vp-p, high impedance) Drive coil (–) Ground (for video signal and DC power) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm Standard angle, f= 9 mm...

  • Page 10: Connections

    CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Insert the plug of this power cord into a wall outlet. The POWER indicator (A) will light.

  • Page 11: Settings

    SETTINGS C-BW VR301 LEVEL VIDEO A. I. VR303 VR302 LENS High speed electronic shutter setting White balance adjustment Normally, the speed setting switches for Table A Normally the WB (white balance) switch is set the high speed electronic shutter are all to the A (automatic) position and the white 1/50 sec.

  • Page 12: Backlight Compensation Setting

    SETTINGS Lens iris adjustment Backlight compensation setting If using a DC type auto-iris lens, you will need to set the LEVEL Use an auto-iris lens and set the EI/BLC switch to the BLC-ON (VR301) volume when shooting in the conditions described below. position, to engage the backlight compensation function.
  • Page 13 SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the When using an auto-iris lens (for indoor/outdoor shortest F stop. Set the EI/BLC switch to the EI-ON position. use) Set the EI/BLC switch to the OFF position. CAUTION: If conditions are outside the electronic iris operation range or more than the maximum illumination, it will cause saturation of the CCD.

  • Page 14: Troubleshooting

    If it still does not perform correctly, This switch lets you select the timing of the automatic switching of please consult your dealer or a Sanyo Authorized Service Centre. the optical filter to colour image or black and white image, according No picture on the monitor screen to the subject brightness.

  • Page 15: Specifications

    SPECIFICATIONS Camera: Scanning system : PAL standard Lens mount : CS mount (or C mount with the (625 TV lines, 25 frames/sec.) supplied adaptor) Interlace : PLL 2:1 interlace Environmental conditions : Temperature: –10˚C ~ +50˚C Humidity: less than 90% Image device : 1/3 inch solid state image device (no condensation)
  • Page 16 SPECIFICATIONS Dimensions: mm 126.5 1/4”–20 UNC 15.4 25.2 Features and specifications are subject to change without prior notice or obligations. English...

Table of Contents