Alternatively, wear a dis- tion, replace the picture tube only with one that is the same type as the original. charging Wrist-strap device. (Be sure to remove it prior to applying power--this is an electric shock precaution.) Samsung Electronics...
Page 3
17. Observe the original lead dress, especially near the following areas : Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the Samsung Electronics...
SCM50/M51/M52: 3.9W, SCM53: 4.4W Built-in mic Condenser mic, omni-directional Operating temperature 0°C to 40°C (32°F to 104°F) Dimension (W x H x D) 101 x 104 x 174.3 (mm) ; 39.7 x 40.9 x 68.6 (inch) Weight 670g (1/49 lbs) Samsung Electronics...
3. Disassembly and Reassembly 3-1. Cabinet and PCB 3-1-1 Ass’y Cover Housing Removal REMOVE 2 SCREWS. "A" Remove the ass'y cover housing in the direction of arrow Fig. 3-1 Ass’y Cover Housing Removal Samsung Electronics...
Page 6
REASSEMBLY : PUT THE 4 TABS INTO THE SLOT, WHILE SLIDING IT AS SHOWN IN DETAIL "B". 1 LOCKING TAB "B" PRECISION SCREW DRIVER < DETAIL "B" > < DETAIL "A" > Fig. 4-2 Ass’y Case Top Removal Samsung Electronics...
PB RF - Pin 11 of CN452 Head Switching Trigger - Pin 9 of CN452 CN452 CN452 PB RF Head Switching - Trigger SW471 J451 DC-JACK Fig. 1 Test point Fig. 2 Test location of test point (Rear Board) Samsung Electronics...
Page 8
The camera will move both zoom and focus lens. The adjustment is finished when the O.K! message appears on the TV screen. Store the data to mode 0A6, 0A7, 0A8, 0A9, 0AA, 0AB, 0AC or 0AD. (3M±1cm) (Be sure to maintain the distance.) LENS 4-22 Samsung Electronics...
Exploded View and Parts List 5-3 Cabinet Assembly (3) Samsung Electronics...
Page 56
Exploded View and Parts List 5-4 Cabinet Assembly (4) Samsung Electronics...
Page 57
Exploded View and Parts List 5-5 EVF/CVF 5-10 Samsung Electronics...
Page 58
Exploded View and Parts List 5-6 Mechanical Parts (1) 5-12 Samsung Electronics...
Page 59
Exploded View and Parts List 5-7 Mechanical Parts (2) 5-14 Samsung Electronics...
Page 60
Exploded View and Parts List 5-8 Mechanical Parts (3) 5-16 Samsung Electronics...
Page 61
Exploded View and Parts List MEMO MEMO 5-18 Samsung Electronics...
Page 62
- Store the data to mode 0B7. - IRIS closed, HALL minimum value found, - IRIS open, HALL maximum value found, - Store the data to mode 00A and mode 00B. - Store the HALL min./max. data to mode 0C1 and mode 0C2. Samsung Electronics 4-23...
Page 63
B-Y axial on screen of the b-1. Aim the camera at a 5100°K gray-scale vectorscope. 3100°K+CCB16) chart illuminated at 1500 to Note : Bright dot shifts after the confirm button is 2000 lx. (40us) pressed. 4-24 Samsung Electronics...
Page 64
7) Be sure to press the “MENU ON/OFF(CON- 50IRE. FIRM)” button to memorize setting. 7) Be sure to press the “MENU ON/OFF(CON- Note : Bright dot shifts after the confirm button is FIRM)” button to memorize setting. pressed. 70IRE 50IRE Samsung Electronics 4-25...
Page 65
(DATA DOWN)” button so that the yellow vec- BLUE VECTOR 346 DEG. tor is 165. 7) Be sure to press the “MENU ON/OFF (CON- FIRM)” button to memorize setting. Note : Bright dot shifts after the confirm button is pressed. 4-26 Samsung Electronics...
Page 66
FIRM)” button to memorize setting. FIRM)” button to memorize setting. Note : Bright dot shifts after the confirm button is Note : Bright dot shifts after the confirm button is pressed. pressed. RED VECTOR 104 DEG. CYAN VECTOR 284 DEG. Samsung Electronics 4-27...
Page 67
EPR : XX EVR : XX EJECT PLAY DATA DOWN DATA UP Confirm MODE UP MODE DOWN MANUAL FOCUS NEAR OSD ON/OFF Note : When XX XX is shown in service adjustment procedures, this indicates variable values. 4-28 Samsung Electronics...
Page 69
PEDESTAL) RED LEVEL GREEN LEVEL YELLOW LEVEL 3. R-Sub Brightness (ADDRESS : 4.R-SUB) 1) Connect an oscilloscope probe to TP-R 2) Adjust the EVR so that R-OUT(Red) level is 8.0Vp-p (pedestal to pedestal). 8.0V (PEDESTAL TO PEDESTAL) 4-30 Samsung Electronics...
Page 70
Ground and “A”part to store the confirmed data in EEPROM when pushing ON/OFF button. 2. BRIGHTNESS 1. PLL 3. R-SUB BRIGHTNESS CVF Adjust Mode (Short) 10P CON 4. B-SUB BRIGHTNESS 5. COLOR ADJ. point 6. HUE Samsung Electronics 4-31...
Page 71
5 seconds. EJECT PLAY DATA DOWN DATA UP Confirm MODE UP MODE DOWN MANUAL FOCUS NEAR OSD ON/OFF Notes : When XX XX is shown in service adjustment procedures, this indicates variable values. 4-32 Samsung Electronics...
Page 72
FIXED FIL/LPF FIL/LPF FIXED PIC/GAIN PICTURE/GAIN FIXED MODE/PLL MODE/PLL ADJUST SYNC GEN SYNC GEN FIXED Y MIRROR NTSC/PAL FIXED OUT INV OUT INV FIXED X MIRROR UP/DOWN FIXED H POSI H-POSITION FIXED HDO OUT HDO OUT FIXED Samsung Electronics 4-33...
Page 73
EVF Adjust Mode (Short) 10P CON Note : When adjusting EVF be sure to short circuit between Ground and “A”part to store the confirmed data in EEPROM when pushing ON/OFF button. After finishing the adjustment, you have to reset. 4-34 Samsung Electronics...
Page 74
Address of the adjustment mode. Name of the adjustment mode. : there are 01h to 1 ch.(refer xxxx) : every address have a name like this (refer xxx) Present data New data : be adjusts before. : be adjusted newly. Samsung Electronics 4-35...
Page 75
5. If you want to finish the adjustment mode, you have to do Battery Reset. The Battery Reset means that you pull out the power source and pull in it again. Then, the adjustment ended and the camcorder works normally. 4-36 Samsung Electronics...
Page 76
REAR PCB JIG SO JIG DETECT JIG SI Fig. 1 Video Signal Connection Note 3 : How to record -1. Insert a recordable tape. -2. Press the SW474 (START/STOP) button on the Rear board in the adjustment mode. Samsung Electronics 4-37...
Page 77
HD SWP (SUB DATA) BATTERY END LEVEL ATF REF. 2. Adjustment * Please keep the order according to explanation. TAPE NONE EQUIPMENT POWER SOURCE 2-1. Model Code 0 OTHER NONE TEST POINT NONE a. Preparation ADDRESS NAME MODEL CODE0 4-38 Samsung Electronics...
Page 78
TEST POINT NONE ADDRESS Model Name Addressed code Model Name Addressed code NAME HD SWP VP-M50 SCM50 b. Connect a power source. VP-M51 SCM51 c. Get into the VCR adjustment mode. VP-M51B SCM52 d. Press the “FADE(MODE UP)” or “BLC(MODE...
Page 79
TEST POINT IC201 PIN13 : This adjustment is perform to set the A/D ADDRESS input level to the regulated level. NAME Y-EMPHASIS IN (HI8) a. Preparations b. Connect a power source. c. Get into the VCR adjustment mode. 4-40 Samsung Electronics...
Page 80
WHITE ( APPROX. 100% ) f. Connect the oscilloscope counter to the APPROX. addressed Test Point. 0.7V 1.0 0.02Vp-p g. Press the “Z.RETURN(DATA DOWN)/ TITLE(DATA UP)” button so that the CN452 APPROX. PIN13 is 0.9±0.02Vp-p from SYNC to peak 0.3V level. Samsung Electronics 4-41...
Page 81
VIDEO OUT signal. JIG SO JIG DETECT * Note : It is a little difficult to adjust because you JIG SI can check the waveform in playback mode even though the adjustment is performed in VCR record mode. 4-42 Samsung Electronics...
Page 82
5.99MHz ±0.02MHz form level smaller than 1Vp-p, press the Data Up button so as to set to up the waveform level. WHITE ( APPROX. 100% ) APPROX. 0.7V 1.0 0.02Vp-p APPROX. 0.3V Samsung Electronics 4-43...
Page 83
OTHER TEST POINT CN452 PIN 10 ADDRESS NAME BPF ADJ b. Connect a power source. c. Get into the VCR adjustment mode. d. Press the “FADE(MODE UP)” or ”BLC(MODE DOWN)” button of FUNCTION so as to select 4-44 Samsung Electronics...
Page 85
5. Set OSD on state. STEP 3 On screen display show “0DF. T.INI XX XX” CAMERA ADJUSTMENT mode has suc- cessfully been activated. Note : When “XX XX” is shown in service adjustment procedures, this indicates variable values. Samsung Electronics...
Page 91
CLUSTER 13 (HEADER[3:0] = 4'b1101); DECODER 1 |----DVAS[7:0]; HORIZENTAL ACTIVE VIDEO START POINT ----| |----DVAE[7:0]; HORIZENTAL ACTIVE VIDEO END POINT CONTROL ----| |----VAVS[7:0]; VERTICAL ACTIVE VIDEO START POINT ----| |----VAVE[7:0]; VERTICAL ACTIVE VIDEO END POINT CONTROL ----| 4-16 Samsung Electronics...
Page 92
----| |---- DCLP_R (7:0) RISING EDGE TIME CONTROL FOR ODM ----| |---- DCLP_F (7:0) FALLING EDGE TIME CONTROL FOR ODM ----| YHAFS YLPFS HAPG (3:0) HORIZONTAL APERTURE GAIN CONTROL |---- APCLP (7:0) HORIZONTAL APERTURE CLIP LEVEL ----| 4-18 Samsung Electronics...
Page 93
OYH_TH (7:0) AE Y SINGLE HIGH THRESHOLD ----| |---- OAECLIP_TH (7:0) AE CLIP COUNT THRESHOLD ----| |---- OAFCLIP_TH (7:0) AF CLIP COUNT THRESHOLD ----| |---- PFCNT_MI (7:0) DEFECT COUNT VALUE FROM MICOM ----| |---- PTHRESH (7:0) DIGITAL CLAMP THRESHOLD VALUE FROM MICOM ----| 4-20 Samsung Electronics...
Page 94
Disassembly and Reassembly 3-1-3 Ass’y Front Removal REMOVE THE ASS'Y FRONT IN THE DIRECTION OF ARROW "A". REMOVE 2 SCREWS. "A" PISCOANECT THE CONNECTOR FROM THE MAIN PCB. Fig.3-3 Ass’y Front Removal Samsung Electronics...
Page 95
3-1-4 Ass’y Case Left Removal REMOVE THE ASS’Y CASE Right IN THE DIRECTION OF ARROW "A". REMOVE 2 SCREWS. "A" DISASSEMBLE AFTER TURNING KNOB to be "LOCK". REMOVE 3 SCREWS. REMOVE 1 SCREWS. Fig. 3-4 Ass’y Case Left Removal Samsung Electronics...
Page 96
3-1-5 Ass’y Case Right Removal PULL OUT THE CASE LEFT ASSEMBLY IN THE DIRECTION OF ARROW "A" DISCONNECT FPC FROM THE CONNECTOR OF THE MAIN PCB. REMOVE 4 SCREWS. REMOVE 1 SCREWS. Fig. 3-5 Ass’y Case Right Removal Samsung Electronics...
Page 97
Disassembly and Reassembly 3-1-6 Ass’y EVF/CVF Removal REMOVE 6 SCREWS. REMOVE THE EVF/CVF ASS’Y IN THE DIRECTION OF ARROW. Fig. 3-6 Ass’y EVF/CVF Removal Samsung Electronics...
Page 98
Disassembly and Reassembly 3-1-7 Ass’y Rear Board Removal REMOVE 2 SCREWS. "A" REMOVE THE ASS'Y FUNCTION BOARD IN THE DIRECTION OF ARROW "A". Fig. 3-7 Ass’y Rear Board Removal Samsung Electronics...
Page 99
PULL OUT THE MAIN POB FROM THE ASS'Y DECK IN THE DIRATION OF ARROW "A". DISCONNECTOR THE FPC FROM THE MAIN PCB. REMOVE THE 2 SCREWS. DISCONNECT CONNECTOR FROM THE HEAD-DRUM. Fig. 3-8 Ass’y Deck and Main PCB Removal Samsung Electronics...
Page 100
REMOVE 2 SCREWS. REMOVESDLDER WITH AN IRON TO ISOPATE SHIELD-CASE AND LENS. DISCONNECT FPC FROM THE CONNECTOR OF THE MAIN PCB. DISCONNECTOR CONNECTOR AND PULL OUT THE ASS'Y LENS IN THE DIRECTION OF ARROW. A Fig. 3-9 Ass’y Camera Removal Samsung Electronics...
Disassembly and Reassembly 3-2. Circuit Boards Location ASS’Y FRONT BOARD ASS’Y MAIN BOARD ASS’Y FUNCTION BOARD ASS’Y REAR BOARD Fig. 3-10 Circuit Boards Location 3-10 Samsung Electronics...
Page 102
ASS’Y LENS PCB CNP01 MAIN PCB CCD PCB CNC01 MAIN PCB FRONT PCB CN701 CN801 CN602 MAIN PCB FUNCTION PCB CN471 CN802 FRONT PCB ASS’Y MIC MIC CONNECTOR CN473 FUNCTION PCB ASS’Y CVF(EVF) CVF(EVF) FPC Fig. 3-11 Connector Diagrams Samsung Electronics 3-11...
Page 103
Disassembly and Reassembly MEMO MEMO 3-12 Samsung Electronics...
Page 104
Monaural, Ø3.5 General Power requirement 7.4 ~ 8.4 V DC Power consumption VP-M50/M51/M51B/M52: 3.9W, VP-M53: 4.4W, VP-M54: 4.9W Built-in mic Condenser mic, omni-directional Operating temperature 0°C to 40°C Dimension (W x H x D) 101 x 104 x 174.3 (mm)