Page 1
FLAT PANEL DISPLAY FWD-32LX1R REMOTE COMMANDER RM-980 SPEAKER SYSTEM SS-SP32FW TABLETOP STAND SU-32FW SERVICE MANUAL 1st Edition (Revised 1)
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. FWD-32LX1R...
Page 3
Gerät abschaltet und signalisiert “Batterie leer” oder nach längerer Gebrauchsdauer der Batterien “nicht mehr einwandfrei funktioniert”. Um sicherzugehen, kleben Sie die Batteriepole z.B. mit einem Klebestreifen ab oder geben Sie die Batterien einzeln in einen Plastikbeutel. 1 (P) FWD-32LX1R...
Page 4
UL60950. the internal conductors may become exposed and cause a SONY is not liable for any damages or injury caused by short circuit or an electrical break. This may cause a fire or using any Wall-Mount Bracket which is not Approved by an electric shock.
Page 5
When mounting the display horizontally 2.5 (1) 25 (9 25 (9 Unit : cm (inches) When mounting the display vertically 2.5 (1) 20 (4) Make sure that POWER switch is at the lower right. Unit : cm (inches) 10 (4) 3 (P) FWD-32LX1R...
3. Remove the seven screws (PSW4 x 12), then hold the two handles and remove the cabinet assembly. Handle Panel Cable cover side securing screws M6 x 20 Knobs 4 x 12 U1 block assembly Handle Cabinet assembly Conductive cushion Installation 4. Reattach the cabinet assembly in the reverse order of steps 1 to 3. FWD-32LX1R...
Chassis assembly Bezel assembly Portions A Harnesses CN9200 CN9300 Conductive cushion H2 board H3 board Installation 5. Reattach the chassis assembly in the reverse order of steps 2 to 4. 6. Reattach the cabinet assembly. (Refer to Section 1-3-1.) FWD-32LX1R...
4. Reattach the shield cover G and two arms in the reverse order of steps 2 and 3. When attaching the two arms, be careful of the orientation of the imprinting. 5. Reattach the cabinet assembly. (Refer to Section 1-3-1.) FWD-32LX1R...
3 x 6 Harness FA1 board Conductive cushion Installation 7. Install the FA1 board and GD board in the reverse order of steps 3 to 6. 8. Reassemble this unit in the reverse order of steps 1 and 2. FWD-32LX1R...
G4 board spacers. Harness BVST 3 x 6 Locking card spacer Conductive cushion Installation 6. Install the G4 board in the reverse order of steps 3 to 5. 7. Reassemble this unit in the reverse order of steps 1 and FWD-32LX1R...
5. Install the S board in the reverse order of steps 3 and 4. 6. Reassemble this unit in the reverse order of steps 1 and Installation 5. Install the K1 board in the reverse order of steps 3 and 6. Reassemble this unit in the reverse order of steps 1 and FWD-32LX1R...
(lower portion). When attaching the control panel assembly, route the harness through the opening. 6. Reassemble this unit in the reverse order of steps 1 and 6. Reattach the cabinet assembly. (Refer to Section 1-3-1.) FWD-32LX1R...
4. Install the light pipe and H3 board in the reverse order of steps 2 and 3. When attaching the cabinet assembly, be careful not to catch the cord. 5. Reattach the cabinet assembly. (Refer to Section 1-3-1.) 1-10 FWD-32LX1R...
5. Reattach the U1 block assembly. (Refer to step 1 of Section 1-3-1.) Conductive cushion Installation 4. Reattach the DC fan in the reverse order of steps 2 and 5. Reattach the cabinet assembly. (Refer to Section 1-3-1.) 1-11 FWD-32LX1R...
5. Reattach the DC fans in the reverse order of steps 3 and 4. 6. Reassemble this unit in the reverse order of steps 1 and Installation 4. Reattach the lithium battery. 5. Reassemble this unit in the reverse order of steps 1 and 1-12 FWD-32LX1R...
5 x 10 assembly Frame LCD module Conductive cushion Harnesses Installation 8. Reattach the LCD module in the reverse order of steps 6 and 7. 9. Reassemble this unit in the reverse order of steps 1 to 5. 1-13 FWD-32LX1R...
Knobs Unit Unit Stands Stands Installation 6. Remove the two stands, four knobs and two arms in the reverse order of steps 3 to 5. 7. Reassemble this unit in the reverse order of steps 1 and 2. 1-14 FWD-32LX1R...
1 LCD module (When sending one or two individual * The glass surface must the capron sheet. packing cartons, put the dummy box.) 7 Lid 6 Cushions B 4 LCD module 5 Cushions A 3 Individual packing carton 9 Carton 1-15 FWD-32LX1R...
→ Flicker can be alleviated by setting the RGB mode to “DTV”. . During two-screen display, flicker occurs when the vertical resolution of the displayed image becomes less than a half. In a motion picture signal, however, the flicker causes no problem during operation. 1-16 FWD-32LX1R...
H05VV-F CEE (13) 53rd (O, C) HVCTF Minimum cord 10 A/125 V 10 A/250 V 10 A/250 V 10 A/125 V set rating Safety approval UL/CSA DENAN-HO 1) Use an appropriate rating plug which complies with local regulations. 1-17 FWD-32LX1R...
Other keys can also be operated in the same way as during Cancellation user adjustment. To cancel the service mode, put the unit into the standby state again using a “STBY” key or turn off the power. 2-2-2. Picture Mode Changes the picture mode as in the ordinary operation. FWD-32LX1R...
Select DVI for input switching. Adjustment range: 0 to 100 Color Tolerance temperature Cool Neutral Warm Specifications 11000K 9300K 6500K 0.276 0.285 0.314 0.9JND 0.282 0.294 0.324 7. Set the DVI input to a full white screen of 20%. FWD-32LX1R...
. Auto Cal. (Refer to Section 2-2-9.) Performs the auto adjustment. . Manual Control AD calibration start-up screen Performs the manual adjustment. ← NTSC/PAL SECAM Analog RGB The same screen is displayed in “Y/C Cal” and AD Service Save “Component Cal”. FWD-32LX1R...
Page 30
. The same screen is displayed in Y/C Cal. Adjustment range: 0 to 255 . C Level . The operations of Auto Cal and Manual Control are the Adjusts the C level. same as NTSC/PAL. Adjustment range: 0 to 255 FWD-32LX1R...
Page 31
Analog RGB → Component Cal. “ENTER” key. . Manual Control ← Performs the manual adjustment. Auto Cal.. Manual Control . Auto Cal.. Performs the auto adjustment. After changing from “Cancel” to “OK”, press the “"ENTER” key. . Manual Control Performs the manual adjustment. FWD-32LX1R...
Page 32
5. Select “AD Calibration” “NTSC/PAL”, and then “Composite Cal.” in a service mode menu. 6. Set “Target Y Cont.” and “Target Color” to an arbitrary target value. During factory setting, “Target Y Cont.” and “Target Color” are adjusted by “2700”. FWD-32LX1R...
Page 33
“2700” as far as possible. 5. Select “AD Calibration”, “NTSC/PAL”, “Y/C Cal.”, 8. Select “Adjust C Level”. (Adjust the color.) and then “Composite Cal.” in a service mode menu. FWD-32LX1R...
Page 34
Dynamic Picture: Color Correct: Chroma: Gamma Correct: Phase: Noise Reduct.: 5. Select “AD Calibration”, “NTSC/PAL”, “Y/C Cal.”, Dynamic Picture: and then “Manual Control” in a service mode menu. Color Correct: 6. Select “Adjust Y Contrast”. (Adjust the contrast.) Gamma Correct: FWD-32LX1R...
Page 35
“User1” to the former value. Noise Reduct.: Dynamic Picture: Chroma: Color Correct: Phase: Gamma Correct: Noise Reduct.: Dynamic Picture: 5. Select “AD Calibration”, “SECAM”, “Composite Cal.”, Color Correct: and then “Manual Control” in a service mode menu. Gamma Correct: FWD-32LX1R...
Page 36
2. Input a 75% color-bar signal to the component input Dynamic Picture: signal, selected in step 1, in a 720/60P format and Color Correct: display the screen. Gamma Correct: 5. Select “AD Calibration”, “SECAM”, “Y/C Cal.”, and then “Manual Control” in a service mode menu. 2-10 FWD-32LX1R...
Page 37
“Adjust Picture” to the former value (value written down in steps 3 and 11) and exit the menu 10. Confirm that BKM-FW11 is installed in an OPTION1 slot. 11. Select the component signal of OPTION1 by input switching. 2-11 FWD-32LX1R...
Page 38
“User1” to the former value. value before change so as to return the setting value of “User1” to the former value. Chroma: Phase: Chroma: Noise Reduct.: Phase: Dynamic Picture: Noise Reduct.: Color Correct: Dynamic Picture: Gamma Correct: Color Correct: Gamma Correct: 2-12 FWD-32LX1R...
Page 39
22. After adjustment is completed, return the setting value separate sync (SOG impossible) SVGA and display of “Adjust Picture” to the former value (value written the screen. down in steps 3 and 21) and exit the menu. 10. Execute steps 3 to 7. 2-13 FWD-32LX1R...
“1” of information display changes to the upper position. 15. Select “Adjust B Offset”. 16. Move a slider and adjust it to the value on whether “R” value “1” of information display changes to the upper position. 2-14 FWD-32LX1R...
The way to cancel the aging mode after it is shifted is as described below. . Turn on and off the standby and AC state. . Input a signal to the current input signal. 2-15 FWD-32LX1R...
The H1 board is a user interface board. It has POWER, INPUT, MENU, UP, DOWN, and ENTER keys. H2 board (For detail, refer to Section 3-5.) The H2 board is a LED board used for making the logo of Sony bright. H3 board (For detail, refer to Section 3-6.) The H3 board has the photosensing block of remote commander and two-color LED that indicate the state of this unit.
The video signal from an LVDS transmitter is output from CN2200. Additionally, the logic power of a panel is supplied to the LCD panel via CN2203. The control signal from a microcomputer is output from CN2202 to a back light module, and power is supplied from CN1005. FWD-32LX1R...
Page 45
Firmware can also be rewritten from an option board. Rewrite can be done without switching SW1000 by controlling the reset of a microcomputer using the signal line of OP_CPU_RST and the setting of a microcomputer write mode using the signal line of OPFWE. FWD-32LX1R...
A current is supplied from CN1203 through a constant-current circuit (IC1202) and integration circuit (consisting of Q1209, Q1211, Q1214, and Q1215) to drive the LED of Sony logo on the H2 board. A pulse signal (LED_IND) signal is input from a microcomputer to the constant-current circuit to change the pulse width and control the brightness.
3-9. S Board The S board amplifies the detection voltage from a temperature sensor (IC9400), which linearly changes with respect to the peripheral temperature, using an operational amplifier and outputs it to the D3 voltage as a DC voltage. FWD-32LX1R...
RY7301 is turned on. After that, the main converter is activated. When a POWER_ON signal is low, Q7300 is turned off and RY7301 is turned off. At that time, the operation of both the active filter and main converter stops. FWD-32LX1R...
Also, 13 V is converted into 5 V and 10.5 V for output using a chopper regulator (consisting of IC7400 and IC7401). A5 V is output to CN7404 (4-5 pins) and 10.5 V is output to CN7404 (1 pin) and CN7401 (3 pin). FWD-32LX1R...
1. Panel error This monitors the operation abnormality of a panel inverter. This unit shuts down when the BL_VREF signal input from CN2202 on the D3 board remains low for two seconds or more after the power is turned on. FWD-32LX1R...
Page 53
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
Cover Block 6-2. Exploded Views M6 x 20 BVTP 3 x 8 BVTP 3 x 8 BVTP 3 x 12 FWD-32LX1R...
Page 57
2-580-628-01 s SCREW, +BVST 3X6 2-580-630-01 s SCREW, +BVST 4X8 2-667-019-01 s HOOK 2-990-241-02 s HOLDER (A), PLUG 3-680-613-12 o SUPPORT, PC BOARD 4-083-966-01 s SCREW, HEXAGON 4-101-182-01 o CUSHION (TOP) 7-628-000-10 s SCREW +PSW M6X20 7-685-646-79 s SCREW +BVTP 3X8 FWD-32LX1R...
Page 58
Chassis Block 5 x 10 BVTP 3 x 8 FWD-32LX1R...
Page 59
2-580-594-01 s SCREW, +PSW M3X12 2-580-628-01 s SCREW, +BVST 3X6 2-580-630-01 s SCREW, +BVST 4X8 2-580-639-01 s SCREW, +BVTP2 4X12 4-052-842-01 s HOLDER, PWB 4-091-379-11 o SPACER, ROCKING CARD 4-092-814-01 o CUSHION D 7-682-673-11 o SCREW 7-685-646-79 s SCREW +BVTP 3X8 FWD-32LX1R...
Page 60
(FOR SS-SP32FW/S (SILVER)) A-1083-767-A s SPEAKER ASSY (32R) (RP) (FOR SS-SP32FW/W (PEARL WHITE)) A-1081-106-A s SPEAKER ASSY (32L) (RP) (FOR SS-SP32FW/S (SILVER)) A-1083-768-A s SPEAKER ASSY (32L) (RP) (FOR SS-SP32FW/W (PEARL WHITE)) 7-682-962-09 s SCREW +PSW 4X10 7-685-661-79 s SCREW +BVTP4X12(EP-FE/ZNBK/CM2 FWD-32LX1R...
Page 61
Overall SU-32FW Part No. SP Description 2-560-385-01 o COVER (REAR), SUPPORT FWD-32LX1R...
1-162-915-11 s CAPACITOR,CERAMIC 10PF/50V CH C1618 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V C1234 1-162-974-11 s CAPACITOR,CERAMIC 0.01MF/50V F C1619 1-127-715-11 s CAPACITOR,CERAMIC 0.22MF B1608 C1235 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C1620 1-127-715-11 s CAPACITOR,CERAMIC 0.22MF B1608 C1236 1-125-837-91 s CAPACITOR,CHIP CERAMIC1MF/6.3V FWD-32LX1R...
Page 63
1-164-935-11 s CAPACITOR,CHIP CERAMIC 470PF C1835 1-127-715-11 s CAPACITOR,CERAMIC 0.22MF B1608 C2053 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C1836 1-162-927-11 s CAPACITOR,CERAMIC 100PF/50V CH C2054 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C1837 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C2055 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF FWD-32LX1R...
Page 64
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2305 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2426 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2306 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2427 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2307 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C2428 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 6-10 FWD-32LX1R...
Page 65
8-719-024-71 s DIODE 1SS362-TE85L CN1005 1-564-509-11 o PLUG,CONNECTOR (6P) D1612 8-719-073-39 s DIODE HZU5.6GTRF CN1006 1-565-269-31 s SOCKET,CONNECTOR(D-DUB,L)9P CN1007 1-764-078-11 s PIN, CONNECTOR (PC BOARD) 3P D1613 8-719-073-39 s DIODE HZU5.6GTRF CN1008 1-564-510-11 o PLUG,CONNECTOR (7P) D1615 8-719-024-71 s DIODE 1SS362-TE85L 6-11 FWD-32LX1R...
Page 66
(TE1) FB2001 1-414-864-11 s INDUCTOR, MICRO (CHIP TYPE) IC1602 ------------ IC M24C02-WMN6T(B) FB2002 1-414-445-11 s FERRITE, EMI (SMD) If this IC has failed, replace the whole D3 board. IC1603 8-759-360-07 s IC BA7657F-E2 IC1604 8-759-596-34 s IC SN74LV4053APWR 6-12 FWD-32LX1R...
Page 67
8-729-928-27 s TRANSISTOR DTA144EE R1023 1-216-829-11 s RESISTOR,CHIP 4.7K 1/10W(1608) R1024 1-216-825-11 s RESISTOR,CHIP 2.2K 1/10W 1608 Q1005 6-550-014-01 s TRANSISTOR SSM6N15FU(TE85R) R1025 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) Q1006 6-550-014-01 s TRANSISTOR SSM6N15FU(TE85R) Q1007 8-729-920-21 s TRANSISTOR DTC314TK(H04) 6-13 FWD-32LX1R...
Page 68
R1225 1-216-864-11 s CONDUCTOR, CHIP (1608) R1315 1-216-864-11 s CONDUCTOR, CHIP (1608) R1226 1-216-864-11 s CONDUCTOR, CHIP (1608) R1316 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1227 1-216-864-11 s CONDUCTOR, CHIP (1608) R1317 1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 6-14 FWD-32LX1R...
Page 69
1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1503 1-216-841-11 s RESISTOR, CHIP 47K 1/10W 1608 R1382 1-216-821-11 s RESISTOR,CHIP 1.0K 1/10W(1608) R1504 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1383 1-216-849-11 s RESISTOR,CHIP 220K 1/16W 1608 R1505 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) 6-15 FWD-32LX1R...
Page 70
1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R1804 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R1658 1-216-801-11 s RESISTOR,CHIP 22 1/10W (1608) R1806 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R1661 1-216-801-11 s RESISTOR,CHIP 22 1/10W (1608) R1807 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 6-16 FWD-32LX1R...
Page 71
1-216-849-11 s RESISTOR,CHIP 220K 1/16W 1608 R2206 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R1882 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 R2210 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 R1883 1-216-821-11 s RESISTOR,CHIP 1.0K 1/10W(1608) R2211 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 6-17 FWD-32LX1R...
Page 72
1-208-643-11 s RESISTOR CHIP 22 1/16W (1005) R2483 1-216-864-11 s CONDUCTOR, CHIP (1608) R2409 1-208-643-11 s RESISTOR CHIP 22 1/16W (1005) R2485 1-216-864-11 s CONDUCTOR, CHIP (1608) R2410 1-208-643-11 s RESISTOR CHIP 22 1/16W (1005) R2487 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-18 FWD-32LX1R...
Page 73
1-234-370-11 s RES, NETWORK 22X4 (1005) RB1219 1-234-372-11 s RES, NETWORK 100X4 (1005) RB2405 1-234-370-11 s RES, NETWORK 22X4 (1005) RB2406 1-234-370-11 s RES, NETWORK 22X4 (1005) RB1220 1-234-372-11 s RES, NETWORK 100X4 (1005) RB2407 1-234-370-11 s RES, NETWORK 22X4 (1005) 6-19 FWD-32LX1R...
Page 74
1-216-797-11 s RESISTOR,CHIP 10 1/10W 1608 R5911 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R5913 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R5915 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R5917 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R5919 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) 6-20 FWD-32LX1R...
Page 75
1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C7314 1-131-992-11 s CAP, CERAMIC 100000PF F 1608 C7315 1-162-970-11 s CAPACITOR CERAMIC 0.01MF/25V B C7420 1-128-526-11 s CAPACITOR,ELECT 100MF/25V C7421 1-100-566-91 s CAPACITOR CERAMIC0.1MF B1608 C7422 1-128-526-11 s CAPACITOR,ELECT 100MF/25V C7423 1-100-566-91 s CAPACITOR CERAMIC0.1MF B1608 6-21 FWD-32LX1R...
Page 76
8-729-820-90 s TRANSISTOR 2SD1621-ST D7201 6-500-501-01 s DIODE D10SC6M-4022 Q7002 8-729-804-41 s TRANSISTOR 2SB1122-S D7202 8-719-060-88 s DIODE D4SBS6 Q7003 6-550-085-01 s TRANSISTOR 2SD2012(SONY.GR) D7203 8-719-060-88 s DIODE D4SBS6 Q7100 6-550-898-01 s TRANSISTOR 2SK3683-01MR-F104 D7300 8-719-948-45 s DIODE ERA22-08 Q7101...
Page 77
R7714 1-218-760-11 s RESISTOR,CHIP 220K 1/10W(2012) R7122 1-216-864-11 s CONDUCTOR, CHIP (1608) R7715 1-218-760-11 s RESISTOR,CHIP 220K 1/10W(2012) R7200 1-216-825-11 s RESISTOR,CHIP 2.2K 1/10W 1608 R7716 1-218-760-11 s RESISTOR,CHIP 220K 1/10W(2012) R7717 1-218-753-11 s RESISTOR CHIP 110K 1/10W(2012) 6-23 FWD-32LX1R...
Page 78
C7619 1-135-960-91 s CAP, CHIP CERAMIC 10MF B(3225) C7620 1-135-960-91 s CAP, CHIP CERAMIC 10MF B(3225) C7621 1-165-669-11 s CAPACITOR,ELECT 220MF C7622 1-165-669-11 s CAPACITOR,ELECT 220MF C7624 1-128-526-11 s CAPACITOR,ELECT 100MF/25V CN7400 1-764-332-11 o PIN, CONNECTOR (9P)(V TYPE) 6-24 FWD-32LX1R...
Page 79
1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R7418 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R7419 1-216-833-11 s RESISTOR,CHIP 10K 1/10W (1608) R7500 1-218-871-11 s RESISTOR,CHIP 10K 1/10W (1608) R7501 1-218-871-11 s RESISTOR,CHIP 10K 1/10W (1608) R7502 1-216-841-11 s RESISTOR, CHIP 47K 1/10W 1608 6-25 FWD-32LX1R...
Page 80
1-573-806-21 s PIN,CONNECTOR (6P)(SMD)(1.5MM) D9203 6-500-012-61 s DIODE NSCW215T-A1A2ST D9204 6-500-012-61 s DIODE NSCW215T-A1A2ST R9200 1-216-864-11 s CONDUCTOR, CHIP (1608) R9201 1-216-864-11 s CONDUCTOR, CHIP (1608) R9202 1-216-864-11 s CONDUCTOR, CHIP (1608) R9203 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-26 FWD-32LX1R...
Page 81
1-126-395-11 s CAPACITOR,ELECT 22MF/16V(CHIP) R5016 1-216-827-11 s RESISTOR, CHIP 3.3K 1/10W 1608 C5055 1-137-980-91 s CAPACITOR,CHIP CERAMIC 0.47MF R5017 1-216-832-11 s RESISTOR,CHIP 8.2K 1/16W 1608 C5056 1-137-980-91 s CAPACITOR,CHIP CERAMIC 0.47MF R5018 1-216-834-11 s RESISTOR,CHIP 12K 1/16W 1608 6-27 FWD-32LX1R...
Page 82
1-537-238-11 s TERMINAL BOARD 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-28 FWD-32LX1R...
Page 83
1-164-505-11 s CAPACITOR,CHIP CERAMIC 2.2MF C3050 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C3051 1-109-982-11 s CAPACITOR,CHIP CERAMIC 1MF/10V C3052 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C3053 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF C3054 1-165-989-11 s CAPACITOR, CERAMIC 10MF (2012) C3055 1-165-669-11 s CAPACITOR,ELECT 220MF 6-29 FWD-32LX1R...
Page 84
1-126-396-11 s CAPACITOR,ELECT 47MF/16V(CHIP) C3311 1-107-820-11 s CAPACITOR,CHIP CERAMIC 0.1MF F C3520 1-126-390-11 s CAPACITOR ELECT 22MF/6.3V(105) C3312 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C3521 1-126-390-11 s CAPACITOR ELECT 22MF/6.3V(105) C3313 1-126-206-11 s CAPACITOR, ELECT 100MF/6.3V C3522 1-126-392-11 s CAPACITOR,CHIP ELECT100MF/6.3V 6-30 FWD-32LX1R...
Page 85
C3579 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C4124 1-107-820-11 s CAPACITOR,CHIP CERAMIC 0.1MF F C3582 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C4125 1-107-820-11 s CAPACITOR,CHIP CERAMIC 0.1MF F C3583 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF C4126 1-119-667-11 s CAPACITOR CERAMIC 22MF/10V(F) 6-31 FWD-32LX1R...
Page 86
1-469-324-21 s FERRITE, EMI (SMD) 4.7UH IC4103 8-759-669-78 s IC TLC2933IPWR-12 FB3001 1-400-141-22 s BEAD, FERRITE (CHIP) (1608) IC4300 8-752-937-39 s IC CXP964032-003R FB3002 1-414-760-21 s INDUCTOR, MICRO (CHIP TYPE) FB3003 1-414-760-21 s INDUCTOR, MICRO (CHIP TYPE) L3000 1-469-525-91 s INDUCTOR 10UH (NLFV25) 6-32 FWD-32LX1R...
Page 87
8-729-026-53 s TRANSISTOR 2SA1576A-T106-QR R3048 1-218-684-11 s RESISTOR,CHIP 470 1/16W (1608) Q3034 8-729-905-35 s TRANSISTOR 2SC4081-R Q3036 8-729-026-53 s TRANSISTOR 2SA1576A-T106-QR R3049 1-216-801-11 s RESISTOR,CHIP 22 1/10W (1608) Q3038 8-729-905-35 s TRANSISTOR 2SC4081-R R3050 1-216-829-11 s RESISTOR,CHIP 4.7K 1/10W(1608) 6-33 FWD-32LX1R...
Page 88
1-216-825-11 s RESISTOR,CHIP 2.2K 1/10W 1608 R3181 1-216-819-11 s RESISTOR,CHIP 680 1/10W 1608 R3114 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3182 1-216-816-11 s RESISTOR, CHIP 390 1/10W 1608 R3115 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3183 1-216-819-11 s RESISTOR,CHIP 680 1/10W 1608 6-34 FWD-32LX1R...
Page 89
1-216-864-11 s CONDUCTOR, CHIP (1608) R3510 1-218-679-11 s RESISTOR,CHIP 300 1/16W (1608) R3266 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3511 1-218-679-11 s RESISTOR,CHIP 300 1/16W (1608) R3267 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3512 1-216-809-11 s RESISTOR,CHIP 100 1/10W 1608 6-35 FWD-32LX1R...
Page 90
R3588 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3948 1-216-864-11 s CONDUCTOR, CHIP (1608) R3589 1-216-805-11 s RESISTOR,CHIP 47 1/10W 1608 R3949 1-216-864-11 s CONDUCTOR, CHIP (1608) R3700 1-216-864-11 s CONDUCTOR, CHIP (1608) R3950 1-216-864-11 s CONDUCTOR, CHIP (1608) 6-36 FWD-32LX1R...
Page 91
1-234-370-11 s RES, NETWORK 22X4 (1005) RB3500 1-234-378-11 s RES, NETWORK 10KX4 (1005) RB3907 1-234-370-11 s RES, NETWORK 22X4 (1005) RB3908 1-234-370-11 s RES, NETWORK 22X4 (1005) RB3501 1-234-372-11 s RES, NETWORK 100X4 (1005) RB3909 1-234-370-11 s RES, NETWORK 22X4 (1005) 6-37 FWD-32LX1R...
Page 112
L - R & ø L/R SW R OUT BUFFER L _ R L & D/A CONVERTER L + R L + R L _ R L + R TREBLE BALANCE VOLUME DAC1 BASS DEC2 VCC9V VCC12V GND1 8-18 8-18 FWD-32LX1R...
Page 141
20 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 µ F 1.5 k Z voltmeter (5.25V) Earth Ground Fig A. Using an AC voltmeter to check AC leakage. FWD-32LX1R...