Related Manuals for Toro 23740
Summary of Contents for Toro 23740
- Page 1 Form No. 3378-184 Rev A Walk-Behind Rotary Broom Model No. 23740—Serial No. 313000001 and Up Model No. 38700—Serial No. 313000001 and Up G021738 *3378-184* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Introduction
You are responsible for operating the machine properly and safely. You may contact Toro directly at www.Toro.com for machine and accessory information, help finding a dealer, or to register your machine. -
Page 3: Table Of Contents
Contents Introduction ..............2 Safety ................4 Training ..............4 Preparation............. 4 Operation............... 4 Clearing a Clogged Broom........5 Maintenance and Storage.......... 5 Slope Indicator ............6 Safety and Instructional Decals ......... 7 Product Overview ............9 Controls ..............9 Specifications ............10 Attachments/Accessories........10 Operation ..............10... -
Page 4: Safety
Safety • Let engine and machine adjust to outdoor temperatures before starting to clear snow. • The operation of any powered machine can result in Read and understand the contents of this manual before foreign objects being thrown into the eyes. Always wear the engine is ever started. -
Page 5: Clearing A Clogged Broom
• Never operate the machine without good visibility or light. • Take all possible precautions when leaving the machine unattended. Shift into neutral, set the parking brake, stop the engine and remove the key. Clearing a Clogged Broom WARNING The rotating broom could cause serious injury. Always use caution when cleaning the broom. -
Page 6: Slope Indicator
Slope Indicator G011841 Figure 3 1. The maximum slope you can safely operate the machine on is 10°. Use the slope indicator to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 10°. Fold along the appropriate line to match the recommended slope. -
Page 7: Safety And Instructional Decals
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 116-8505 112-9028 1. Explosion/Fire hazard–Read the Operator’s Manual. Stop engine before filling fuel tank. Leave 5/8 inch (16mm) at top 1. Warning—stay away from moving parts; keep all guards in of tank for fuel expansion-Do Not overfill tank. - Page 8 116-7370 1. Warning-Read the Operator’s Manual. Do Not operate this 4. Warning-Stop engine and remove spark plug before adjusting, machine unless you are trained. Stay away from moving servicing, or cleaning machine and attachments. Before parts; keep all guards in place. leaving the operator’s position, disengage broom, traction drive, and stop engine.
-
Page 9: Product Overview
Fuel Shut-Off Valve Product Overview The fuel shut-off valve is the lower lever located on the rear left hand side of the engine below the choke. The fuel shut-off valve shuts off the flow of fuel when the machine will not be used for a few days, when parking inside a building, and during transport to and from the job. -
Page 10: Specifications
3. Allow the engine to run for a minimum of 15 seconds, its capabilities. Contact your Authorized Service Dealer or then turn the engine On/Off switch to the Off position Distributor or go to www.Toro.com for a list of all approved to stop the engine. attachments and accessories. - Page 11 Adjusting the Traction Cable (page 18)) or contact your authorized Toro dealer. Driving Forward 1. Place the speed selector lever to the desired forward position, making sure it locks in the notch (Figure 6). Figure 8 Note: Similarly, squeezing the left wheel clutch lever turns the machine to the left.
- Page 12 If the broom height is adjusted too low, the machine may move more forcefully in the reverse direction, causing injury and/or property damage. Carefully check the broom height and adjust it properly or contact your authorized Toro dealer.
- Page 13 Figure 11 Figure 12 1. 51-102 mm (2–4 inches) 3. Swept area 1. Caster wheel tube 3. Pin maximum width 2. Positions to achieve 3 mm 4. Adjuster sleeve 2. Length of broom (1/8 inch) increments 7. Adjust the broom height if necessary. •...
-
Page 14: Transporting The Machine
the front of the machine on the pavement. Repeat if necessary. • If you cannot unclog the broom by bumping the front of the machine: – Park the machine on level ground. Stop the engine, wait for all moving parts to stop, and remove the spark plug wire(s). -
Page 15: Maintenance
• Have an authorized service dealer inspect and replace the traction drive belt, if necessary. Important: You can find more information about maintaining and servicing your machine at www.Toro.com. Important: Refer to your engine operator's manual for additional maintenance procedures. For engine adjustments,... -
Page 16: Checking The Engine Oil Level
Tighten the hardware or Service Interval: Before each use or daily correct the problem before operating. Engine Oil Type: Toro 4–Cycle Premium Engine Oil Changing the Engine Oil 1. Turn off the engine and wait for all moving parts to stop. -
Page 17: Checking The Spark Plug
Checking the Spark Plug 2. Lubricate the broom angle lock pin fitting with NGLI grade #2 multi-purpose gun grease. Service Interval: Every 160 hours Remove the spark plug, check the condition and reset the gap, or replace with a new plug. See your Engine Owner's Manual. Checking the Broom Cable Service Interval: After the first 2 hours Yearly... -
Page 18: Checking The Broom Segments
4. If the shear pin is damaged, remove the pin and replace If the machine does not drive in the forward or reverse speeds with a Toro recommended pin. Secure the pin with or it drives when you release the traction lever, adjust the a nut. -
Page 19: Adjusting The Wheel Clutch Cable
Storage WARNING • Gasoline vapors can explode. • Do not store gasoline more than 30 days. • Do not store the machine in an enclosure near an open flame. • Allow the engine to cool before storing it. Preparing the Machine for Storage Figure 20 1. -
Page 20: Removing The Machine From Storage
Removing the Machine from Storage 1. Remove the spark plug and spin the engine rapidly using the starter to blow the excess oil from the cylinder. 2. Install the spark plug by hand and then torque it to 20.4 N-m (15 ft-lb). 3. -
Page 21: Troubleshooting
Troubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to use. When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank. The following table lists some of the common causes of trouble. - Page 22 Problem Possible Cause Corrective Action There is abnormal vibration. 1. The broom assembly is loose or 1. Tighten the hardware. Replace damaged. the broom assembly or contact an authorized service dealer. 2. The engine mounting bolts are loose. 2. Tighten the engine mounting bolts. 3.
- Page 23 Notes:...
- Page 24 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.