hit counter script
Pioneer AVH-P4000DVD Installation Manual
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Car Video System
  5. Super Tuner IIID AVH-P4000DVD
  6. Installation manual

Pioneer AVH-P4000DVD Installation Manual

Hide thumbs Also See for AVH-P4000DVD:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

Download this manual See also: Service Manual, Installation Manual
Enlarged version
AVH-P4000DVD
Printed in Thailand
Напечатано в Таиланде
<CRD4280-A/N> RE
<KSNNX> <07K00000>
Connecting the units
WARNING
Note
• To avoid the risk of accident and the potential
• This unit cannot be installed in a vehicle without
violation of applicable laws, the front DVD or TV
ACC (accessory) position on the ignition switch.
(sold separately) feature should never be used
while the vehicle is being driven. Also, Rear
Displays should not be in a location where it is a
visible distraction to the driver.
• In some countries or states the viewing of images
on a display inside a vehicle even by persons
other than the driver may be illegal. Where such
regulations apply, they must be obeyed and this
unit's DVD features should not be used.
ACC position
No ACC position
CAUTION
• Use this unit in other than the following
• PIONEER does not recommend that you
conditions could result in fire or malfunction.
install or service your display yourself.
— Vehicles with a 12-volt battery and negative
Installing or servicing the product may
grounding.
expose you to risk of electric shock or other
— Speakers with 50 W (output value) and 4 ohm
hazards. Refer all installation and servicing
to 8 ohm (impedance value).
of your display to authorized Pioneer service
• To prevent short-circuit, overheating or
personnel.
malfunction, be sure to follow the directions
• Secure all wiring with cable clamps or
below.
electrical tape. Do not allow any bare wiring
— Disconnect the negative terminal of the
to remain exposed.
battery before installation.
• Do not drill a hole into the engine
— Secure the wiring with cable clamps or
compartment to connect the yellow lead
adhesive tape. To protect the wiring, wrap
of the unit to the vehicle battery. Engine
adhesive tape around them where they lie
vibration may eventually cause the insulation
against metal parts.
to fail at the point where the wire passes from
— Place all cables away from moving parts, such
the passenger compartment into the engine
as gear shift and seat rails.
compartment. Take extra care in securing the
— Place all cables away from hot places, such as
wire at this point.
near the heater outlet.
• It is extremely dangerous to allow the display
— Do not pass the yellow cable through a hole
lead to become wound around the steering
into the engine compartment to connect to a
column or gearshift. Be sure to install the
battery.
display in such a way that it will not obstruct
— Cover any disconnected cable connectors with
driving.
insulating tape.
• Make sure that wires will not interfere with
— Do not shorten any cables.
moving parts of the vehicle, such as the
— Never cut the insulation of the power cable of
gearshift, parking brake or seat sliding
this unit in order to share the power to other
mechanism.
equipment. Current capacity of the cable is
• Do not shorten any leads. If you do, the
limited.
protection circuit may fail to work properly.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
WARNING
— Never band together multiple speaker's
negative cables.
LIGHT GREEN LEAD AT POWER CONNECTOR
IS DESIGNED TO DETECT PARKED STATUS
AND MUST BE CONNECTED TO THE POWER
SUPPLY SIDE OF THE PARKING BRAKE SWITCH.
IMPROPER CONNECTION OR USE OF THIS
LEAD MAY VIOLATE APPLICABLE LAW AND MAY
RESULT IN SERIOUS INJURY OR DAMAGE.
Connecting the units
• Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp's system remote control or
the vehicle's auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is equipped
with a glass antenna, connect it to the antenna
booster power supply terminal.
• Never connect blue/white cable to external power
amp's power terminal. Also, never connect
it to the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product's ground cable (especially, high-current
products such as power amp) must be wired
separately. Otherwise, fire or malfunction may
result if they are accidentally detached.
Connecting the units
Parts supplied
Parts marked (*) are pre-installed.
This product
Power cord
USB cable
Holder*
Side bracket (2 pcs.)*
Trim ring
Frame
Flush surface screw
Binding screw
(5 × 6 mm) (8 pcs.)
(5 × 6 mm) (8 pcs.)
(4 pcs. are pre-installed.)
Binding screw*
Rubber bush
Double-ended screw
(3 × 6 mm) (8 pcs.)
Touch panel pen

Advertisement

Table of Contents
loading

Related Manuals for Pioneer AVH-P4000DVD

Summary of Contents for Pioneer AVH-P4000DVD

  • Page 1 (especially, high-current • Use this unit in other than the following products such as power amp) must be wired • PIONEER does not recommend that you conditions could result in fire or malfunction. separately. Otherwise, fire or malfunction may install or service your display yourself.

  • Page 2: Connecting The Units

    Connecting the units Connecting the units Connecting the units Connecting the units Connecting the power cord When connecting to separately sold power amp Connecting the system This product Note: Depending on the kind of vehicle, the This product USB cable Power amp function of 3* and 5* may be different.

  • Page 3: When Connecting With A Multi-Channel Processor

    Connecting the units Connecting the units Connecting the units When connecting with a multi-channel processor When connecting with a rear view camera When connecting the external video component and the display When this product is used with a rear view camera, it is possible to automatically switch from the video to rear view image when the gear shift is moved to REVERSE (R).

  • Page 4: Installation With The Holder And Side Bracket

    Installation Installation Installation with the holder 3. Attach the trim ring. 2. Fastening the unit to the factory Note radio-mounting bracket. and side bracket Position the unit so that its screw holes are • Check all connections and systems before final 1.

  • Page 5: Подключение Устройств

    Будьте уверены, что соединяете соединители одинакового цвета среди соединителей с • Использование данного устройства в иных, цветовым кодированием. • PIONEER не рекомендует вам самостоятельно чем следующие условия, может привести к • Черный кабель – заземление. Этот кабель и производить установку или обслуживание...
  • Page 6 Подключение устройств Подключение устройств Подключение устройств Подключение устройств Соединительный шнур питания Соединение с усилителем мощности, который продается Подключение системы отдельно Данное устройство Примечание: В зависимости от типа автомобиля Данное Кабель USB функции 3* и 5* могут быть Усилитель мощности устройство Подключить...
  • Page 7 Подключение устройств Подключение устройств Подключение устройств Подключение многоканального процессора Подключение камеры заднего обзора Подключение внешнего видео компонента и дисплея Когда данное устройство используется с камерой заднего обзора, можно автоматически переключить от видео к изображению заднего обзора, когда рычаг переключения коробки передач...
  • Page 8 Установка Установка Установка с держателем и 3. Прикрепите декоративное кольцо 2. Закрепление устройства с Примечания боковым кронштейном фабричным радиомонтажным кронштейном. • Проверьте все соединения и системы перед 1. Установите держатель в Установите устройство так, чтобы окончательной установкой. приборную панель. его винтовые отверстия совпадали с •...

Table of Contents