hit counter script
Acer X193W Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Monitor
  5. X193W
  6. Service manual

Acer X193W Service Manual

Hide thumbs Also See for X193W:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Acer X193W
Service Guide
Service Guide Version and Revision
1

Advertisement

Table of Contents
loading

Related Manuals for Acer X193W

Summary of Contents for Acer X193W

  • Page 1 Acer X193W Service Guide Service Guide Version and Revision...
  • Page 2 Version Release Date Revision History TPV model Aug.-20-2007 Initial Release T97SNADC2WAGHC Copyright...
  • Page 3 Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
  • Page 4 DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines. Warning: (For FCC Certified Models) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 5 Precautions Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable trolley, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.

  • Page 6: Table Of Contents

    Table Of Contents Chapter 1 Monitor Features ………………………………………… Introduction ……………………………………… Electrical Requirements ……………………………………… LCD Monitor General Specification ……………………………………… LCD Panel Specification ……………………………………… Support Timing ……………………………………… Monitor Block Diagram ……………………………………… Main Board Diagram ……………………………………… Software Flow chart ……………………………………… Main Board Layout ………………………………………...

  • Page 7: Chapter 1 Monitor Features

    This will alleviate the growing health concerns. It is also a space saving design, allowing more desktop space, and comparing to the traditional CRT monitor, it consumes less power and gets less weight in addition MTBF target is 50k hours or more. Chart of X193W Panel LTM190M2-L31...

  • Page 8: Electrical Requirements

    Electrical Requirements Standard Test Conditions All tests shall be performed under the following conditions, unless otherwise specified. Ambient light Dark room Viewing distance 30-50 cm for LCD performance Warm up time ＞30 minutes All specifications Measuring equipment Photo detector PR650 w/2° Measurement field Control temperature 6500°...

  • Page 9: Lcd Monitor General Specification

    LCD Monitor General Specification Driving system TFT Color LCD Active Display Area 408.24(H) × 255.15mm(V) LCD Panel Pixel pitch 0.2835 x 0.2835 Contrast Ratio 1000 : 1 Response time Separate Sync. H/V TTL Input H-Frequency 30kHz – 80kHz V-Frequency 55-75Hz Viewing angle 90∘...

  • Page 10: Lcd Panel Specification

    LCD Panel Specification General Specifications Absolute Maximum Ratings...
  • Page 11 Optical Specifications...

  • Page 12: Support Timing

    Support Timing...

  • Page 13: Monitor Block Diagram

    Monitor Block Diagram The LCD MONITOR will contain a main board, a power board, and keypad board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.

  • Page 14: Main Board Diagram

    Main Board Diagram Crystal LCD Interface (X201) (CN402) 12MHz Scalar IC NT68665MFG-128 (Include MCU ,ADC,flash rom OSD) EEPROM (U203) M24C16 (U204) H sync V sync Key Board D-Sub Control Connector Connector CN407 (CN101) (CN102)

  • Page 15: Software Flow Chart

    Software Flow Chart...
  • Page 16 Remark: 1) MCU initializes. 2) Is the EEPROM blank? 3) Program the EEPROM by default values. 4) Get the PWM value of brightness from EEPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.

  • Page 17: Main Board Layout

    Main Board Layout Symbol Description Symbol Description ZD201 093G 39G586 U304 056G 56327A ZD103 093G 39S 24 T CN301 033G3802 9 FB107 071G 56D121 CN101 088G 35315F H FB206 071G 56D121 JA CN402 033G801930F CH JS U301 056G 563 52 CN102 088G 35424F N U203...

  • Page 18: Installation

    Installation...

  • Page 19: Attaching/Removing The Base

    Attaching/Removing the Base...

  • Page 20: Chapter 2 Operating Instructions

    Chapter 2 Operating Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. •...

  • Page 21: Front Panel Controls

    Front Panel Control...

  • Page 22: Ecolor Management (Osd)

    eColor Management (OSD)

  • Page 23: How To Adjust A Setting

    How to Adjust a Setting...
  • Page 24 Adjusting the picture...

  • Page 27: Osd Message

    OSD Message a. Outline b. The Description For OSD Message Item Description Auto Config When Analog signal input, if User Press Hot-Key “Auto”, will show this message, and the Please Wait monitor do the auto config function. Input Not When the Hsync Frequency, Vsync Frequency or Resolution is out of the monitor Supported support range, will show this message.

  • Page 28: Logo

    Logo When the monitor is power on, the LOGO will be showed in the center, and disappear slowly. How To Optimize The DOS-Mode Plug And Play Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.

  • Page 29: Chapter 3 Machine Disassembly

    Chapter 3 Machine Disassembly This chapter contains step-by-step procedures on how to disassemble the monitor for maintenance. Disassembly Procedure 1. Remove the cover hinge marked in red. (Fig 1) Fig 1 2. Remove the screws as following indicate to release base stand . (Fig 2) Fig 2...
  • Page 30 3. Remove the back cover and regard the hook. (Fig 3-4) Fig 3 Fig 4...
  • Page 31 4. Remove the keyboard. (Fig 5) Fig 5 5. Remove the bezel. (Fig 6) Fig 6...
  • Page 32 6. Remove the screws to remove the panel. (Fig 7-9) Fig 7 Fig 8 Fig 9...
  • Page 33 7. Remove the screw as following indicate to remove the main board, audio board and power board. (Fig 10-12) Fig 10 Fig 11...
  • Page 34 Fig 12...

  • Page 35: Chapter 4 Troubleshooting

    Chapter 4 Troubleshooting This chapter provides troubleshooting information for the X193W: 1. No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the power section Measure U301 Pin2=3.3V, U304 Pin...
  • Page 36 2. No Picture No picture Measure U301 Pin2=3.3V, U304 Pin 2=1.8V Replace U301,U304 Check if X201oscillate waveforms are normal Replace X201 Check if the sync signal from computer is output and video cable is connected normally Input the sync signal of computer, or change the cable Replace U203...
  • Page 37 3. Panel Power Circuit Check the PPWR panel power relative circuit Q301, Q302 Check CN402 PIN1 should have In normal operation, when LED =green, Q301B =5 V, response from 0V to 5V When we If PPWR no-response when the power switch switch the power switch from on to off Turn on and turn off, replace the U203 Replace panel...
  • Page 38 5. No Backlight Check C802 (+) =12V Change F801 Check ON/OFF signal Check Interface board Check IC801 pin12=12V? Change Q805.Q808 or Q810 Check the pin9&10 of IC801 have PWM wave Change Q801/Q804/Q811/Q812 Replace IC801 Check the resonant wave of pin3 & pin7 for T801,T802 Check Q802/Q803 Check the output of T801/T802 Change T801/T802...

  • Page 39: Chapter 5 Connector Information

    Chapter 5 Connector Information The following figure shows the connector locations on the monitor:...

  • Page 41: Chapter 6 Fru (Field Replacement Unit) List

    FRU parts for repair and service of customer machines. NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.

  • Page 42: Exploded Diagram

    Exploded Diagram (Model: X193W)
  • Page 43 Part List Above picture show the description of the following component. Item Picture Description Base shield Panel...
  • Page 44 Power Board Main Board...

  • Page 45: Schematic Diagram

    R144 1K 1/16W VGA_CABLE C130 0.1uF 16V T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL X193W/P193W Size 絬 隔 瓜 絪 腹 G2561-A-AC-X-1-070722 TPV MODEL ACER K ey Component 02.D-SUB/DVI PCB NAME 715G2561-A-AC 称称...
  • Page 46 BIN- GIN+ GIN- RIN+ RIN- T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size X193W/P193W OPTION(HDCP) 絬 隔 瓜絪 腹 G2561-A-AC-X-1-070722 TPV MODEL ACER Key Component 03.MCU+SCALER NT68665 PCB NAME 715G2561-A-AC < 称 称...
  • Page 47 4K7 1/16W 0.1uF 16V BL_CONTROL 3 2N3904S-RTK/PS T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size X193W/P193W 絬 隔 瓜 絪 腹 G2561-A-AC-X-1-070722 TPV MODEL ACER Key Component 04.DC-DC PCB NAME 715G2561-A-AC 称称 称称...
  • Page 48 LED_G LED_O OPTION(AUDIO CONTROL) LF_B NC/CONN T P V ( Top Victory Electronics Co . , Ltd. ) OEM MODEL Size X193W/P193W 絬 隔 瓜 絪 腹 G2561-A-AC-X-1-070722 TPV MODEL ACER Key Component 05.CONNECTOR PCB NAME 715G2561-A-AC 称称 称称 <...
  • Page 49 Power board 1/4W R918 F902 0R05 1/4W 1K 1/4W 1K 1/4W 1K 1/4W 1K 1/4W +14V 1/4W R919 L904 C912 1.1uH 0.001uF ZD902 1/4W R920 RLZ16B C917 C918 C922 680uF/25V 680uF/25V R929 1K 1/8W T901 ZD901 D906 Q902 SP10100 BD901 PMBS3904 R936 KBP208G...
  • Page 50 T801 POWER X'FMR D805 R817 R821 CN801 BAW56 10K 1/10W 1K 1/10W 1% R855 CONN 1/4W C839 F801 1000pF C819 0R05 1/4W 0.0022uF +12V C801 C802 10pF/3KV 470uF/25V C824 R801 D801 3.6K 1/10W 0.1uF R856 1K 1/10W 1% BAV99 R819 R804 1/4W 1/8W...

Table of Contents