Page 1 Grid Solutions Feeder Protection System Instruction Manual Product version: 7.41x GE publication code: 1601-0093-AE1 (GEK-130980) E83849 LISTED IND.CONT. EQ. 52TL 1601-0093-AE1...
Page 2 The contents of this manual are the property of GE Multilin Inc. This documentation is furnished on license and may not be reproduced in whole or in part without the permission of GE Multilin. The content of this manual is for informational use only and is subject to change without notice.
Page 3: Table Of Contents
Environmental........................2-36 2.5.12 Type tests ..........................2-37 2.5.13 Production tests ........................2-37 2.5.14 Approvals ..........................2-38 2.5.15 Maintenance.........................2-38 3 INSTALLATION Unpack and inspect..................3-1 Panel cutouts....................3-2 3.2.1 Horizontal units ........................3-2 3.2.2 Vertical units ........................... 3-3 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 4 3.7.5 Automatic discovery of UR devices................3-59 Connect to the F60 ..................3-60 3.8.1 Connect to the F60 in EnerVista.................. 3-60 3.8.2 Use Quick Connect via the front panel RS232 port..........3-61 3.8.3 Use Quick Connect via a rear Ethernet port............3-62 Set up CyberSentry and change default password .........3-62...
Page 5 5.5.1 AC inputs ..........................5-129 5.5.2 Power system........................5-130 5.5.3 Signal sources........................5-131 5.5.4 Breakers..........................5-134 5.5.5 Disconnect switches ......................5-138 5.5.6 FlexCurves...........................5-141 5.5.7 Phasor Measurement Unit ..................5-148 FlexLogic......................5-168 5.6.1 FlexLogic operands ......................5-168 5.6.2 FlexLogic rules ........................5-181 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 6 Test mode forcing......................5-334 5.12.3 Phasor Measurement Unit test values..............5-335 5.12.4 Force contact inputs ..................... 5-336 5.12.5 Force contact outputs ....................5-336 6 ACTUAL VALUES Actual Values menu..................6-1 Front panel......................6-3 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 7 Product information..................6-31 6.6.1 Model information......................6-31 6.6.2 Firmware revisions ......................6-32 7 COMMANDS AND Commands menu .................... 7-1 TARGETS 7.1.1 Virtual inputs........................... 7-2 7.1.2 Clear records .......................... 7-2 7.1.3 Set date and time......................... 7-3 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 8 10.9 Battery ......................10-14 10.9.1 Replace battery for SH/SL power supply ............. 10-14 10.9.2 Dispose of battery ......................10-15 10.10 Clear files and data after uninstall............10-18 10.11 Repairs......................10-19 10.12 Storage ......................10-19 10.13 Disposal ......................10-20 viii F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 9 A.1 FlexAnalog items .....................A-1 OPERANDS B RADIUS SERVER B.1 RADIUS server configuration ................. B-1 CONFIGURATION C COMMAND LINE C.1 Command line interface .................C-1 INTERFACE D MISCELLANEOUS D.1 Warranty ......................D-1 D.2 Revision history ....................D-1 ABBREVIATIONS INDEX F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 10 TABLE OF CONTENTS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 11: Introduction
Ensure that the control power applied to the device, the AC current, and voltage input match the ratings specified on the relay nameplate. Do not apply current or voltage in excess of the specified limits. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 12: For Further Assistance
Fax: +1 905 927 5098 Worldwide e-mail: multilin.tech@ge.com Europe e-mail: multilin.tech.euro@ge.com Website: http://www.gegridsolutions.com/multilin When contacting GE by e-mail, optionally include a device information file, which is generated in the EnerVista software by clicking the Service Report button. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 13 CHAPTER 1: INTRODUCTION FOR FURTHER ASSISTANCE Figure 1-1: Generate service report F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 14 FOR FURTHER ASSISTANCE CHAPTER 1: INTRODUCTION F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 15: Product Description
This chapter outlines the product, order codes, and specifications. 2.1 Product description 2.1.1 Overview The F60 Feeder Protection System is part of the Universal Relay (UR) series of products. It is a microprocessor-based relay for feeder protection. Overvoltage and undervoltage protection, overfrequency and underfrequency protection, breaker failure protection, directional current supervision, fault diagnostics, remote terminal unit (RTU), and programmable logic functions are provided.
Page 16 Secure Routable GOOSE (R-GOOSE) is supported with software options. Settings and actual values can be accessed from the front panel or EnerVista software. The F60 uses flash memory technology that allows field upgrading as new features are added. Firmware and software are upgradable.
Page 17: Security
The F60 supports password entry from a local or remote connection. Local access is defined as any access to settings or commands via the faceplate interface. This includes both keypad entry and the through the faceplate RS232 port. Remote access is defined as any access to settings or commands via any rear communications port.
Page 18 When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password applies.
Page 19 |--------------- Virtual Inputs |--------------- Contact Outputs |--------------- Virtual Outputs |--------------- Resetting |--------------- Direct Inputs |--------------- Direct Outputs |--------------- Teleprotection |--------------- Direct Analogs |--------------- Direct Integers |---------- Transducer I/O |---------- Testing |---------- Front Panel Labels Designer F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 20 The UR has been designed to direct automatically the authentication requests based on user names. In this respect, local account names on the UR are considered as reserved and not used on a RADIUS server. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 21: Order Codes
The order code is on the product label and indicates the product options applicable. The F60 is available as a 19-inch rack horizontal mount or reduced-size (¾) vertical unit. It consists of the following modules: power supply, CPU, CT/VT, contact input and output, transducer input and output, and inter-relay communications.
Page 22 Enhanced front panel with Chinese display and user-programmable pushbuttons Enhanced front panel with Turkish display Enhanced front panel with Turkish display and user-programmable pushbuttons Enhanced front panel with German display Enhanced front panel with German display and user-programmable pushbuttons F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 23 Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels * When an 8Z module is ordered, slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 24 ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION Table 2-5: F60 order codes for reduced-size vertical units - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 25 Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels * When an 8Z module is ordered, slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-11...
Page 26: Order Codes With Process Bus Modules
ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION 2.3.2 Order codes with process bus modules Table 2-6: F60 order codes for horizontal units with process bus - * ** - * * * - F ** - H ** - M **...
Page 27 Channel 1 - RS422; Channel 2 - 1300 nm, single-mode, Laser Channel 1 - G.703; Channel 2 - 1300 nm, single-mode Laser G.703, 1 Channel G.703, 2 Channels RS422, 1 Channel 7W RS422, 2 Channels F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-13...
Page 28 ORDER CODES CHAPTER 2: PRODUCT DESCRIPTION Table 2-7: F60 order codes for reduced-size vertical units with process bus - * ** - * * * - F ** - H ** - M ** - P/R ** Reduced Size Vertical Mount (see note regarding P/R slot below)
Page 29: Replacement Modules
Replacement modules can be ordered separately. When ordering a replacement CPU module or faceplate, provide the serial number of your existing unit. Not all replacement modules apply to the F60 relay. The modules specified in the order codes for the F60 are available as replacement modules for the F60.
Page 30 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs * When an 8Z module is ordered, slot F must have an 8F or 8G module. 2-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 31 4 RTD inputs, 4 DCmA outputs (only one 5D module is allowed) 4 DCmA inputs, 4 RTD inputs 8 DCmA inputs * When an 8Z module is ordered, slot F must have an 8F or 8G module. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-17...
Page 32: Signal Processing
The UR samples its AC signals at 64 samples per cycle, that is, at 3840 Hz in 60 Hz systems, and 3200 Hz in 50 Hz systems. The sampling rate is dynamically adjusted to the actual system frequency by an accurate and fast frequency tracking system. The A/D converter has the following ranges of AC signals: 2-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 33 Measured analog values and binary signals can be captured in COMTRADE format with sampling rates from 8 to 64 samples per power cycle. Analog values can be captured with Data Logger, allowing much slower rates extended over long period of time. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-19...
Page 34: Specifications
> 2.0 × CT: ±1.5% of reading > 2.0 × CT rating Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I t; FlexCurves™ (programmable); Definite Time (0.01 s base curve) Curve multiplier: Time Dial = 0.00 to 600.00 in steps of 0.01...
Page 35 0.1 to 2.0 x CT rating ±1.5% of reading > 2.0 x CT rating Curve shapes: IEEE Moderately/Very/Extremely Inverse; IEC (and BS) A/B/C and Short Inverse; GE IAC Inverse, Short/Very/ Extremely Inverse; I t; FlexCurves™ (programmable); Definite Time (0.01 s base...
Page 36 <30 ms at 0.9 pickup at 60 Hz for Definite Time mode AUXILIARY UNDERVOLTAGE Pickup level: 0.004 to 3.000 pu in steps of 0.001 Dropout level: 102 to 103% of pickup Level accuracy: ±0.5% of reading from 10 to 208 V 2-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 37 Typical times are average operate times including variables such as frequency change instance, test method, and so on, and can vary by ±0.5 cycles. OVERFREQUENCY Pickup level: 20.00 to 65.00 Hz in steps of 0.01 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-23...
Page 38 ±3% of operate time or ±42 ms, whichever is greater Operate time: <42 ms at 1.10 × pickup at 60 Hz BREAKER RESTRIKE Principle: detection of high-frequency overcurrent condition ¼ cycle after breaker opens 2-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 39 ±500 ms or 2%, whichever is greater for I < 0.9 × k × I and I / (k × I ) > 1.1 TRIP BUS (TRIP WITHOUT FLEXLOGIC) Number of elements: Number of inputs: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-25...
Page 40: User-Programmable Elements
LEDs on Test sequence 2: all LEDs off, one LED at a time on for 1 s Test sequence 3: all LEDs on, one LED at a time off for 1 s 2-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 41: Monitoring
DATA LOGGER Number of channels: 1 to 16 Parameters: any available analog actual value Sampling rate: 15 to 3600000 ms in steps of 1 Trigger: any FlexLogic operand Mode: continuous or triggered F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-27...
Page 42: Metering
±1.0% of reading at –1.0 ≤ PF < –0.8 and 0.8 < PF ≤ 10 REACTIVE POWER (VARS) Accuracy at 0.1 to 1.5 x CT rating and 0.8 to 1.2 x VT rating: ±1.0% of reading at –0.2 ≤ PF ≤ 0.2 2-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 43: Inputs
0.002 to 4.6 × CT rating RMS symmetrical HI-Z CT module: 0.002 to 4.6 × CT rating RMS symmetrical Current withstand: 20 ms at 250 times rated 1 sec at 100 times rated continuous 4xInom F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-29...
Page 44 36 V pk-pk IRIG-B INPUT IRIG formats accepted: B000…B007, B120…B127 IRIG control bits: IEEE Std C37.118.1-2011 Amplitude modulation: 1 to 10 V pk-pk DC shift: TTL–Compatible Input impedance: 50 kΩ Isolation: 2 kV 2-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 45: Power Supply
INTERNAL FUSE Ratings: Low range power supply: 8 A / 250 V High range power supply: 4 A / 250 V Interrupting capacity: 100 000 A RMS symmetrical 10 000 A F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-31...
Page 46: Outputs
48 V 0.5 A 125 V 0.3 A 250 V 0.2 A Operate time: < 8 ms Contact material: silver alloy FAST FORM-C RELAY Make and carry: 0.1 A max. (resistive load) 2-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 47 99% Settling time to a step change: 100 ms Isolation: 1.5 kV Driving signal: any FlexAnalog quantity Upper and lower limit for the driving signal: –90 to 90 pu in steps of 0.001 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-33...
Page 48: Communication Protocols
PARALLEL REDUNDANCY PROTOCOL (PRP) (IEC 62439-3 CLAUSE 4, 2012) Ethernet ports used: 2 and 3 Networks supported: 10/100 Mb Ethernet OTHER TFTP, SFTP, HTTP, IEC 60870-5-104, Ethernet Global Data (EGD), IEEE C37.118 2-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 49: Inter-Relay Communications
At extreme temperatures these values deviate based on component tolerance. On average, the output power decreases as the temperature is increased by a factor of 1 dB / 5 °C. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-35...
Page 50: Cybersentry Security
95% (non-condensing) at 55°C (as per IEC60068-2-30 variant 1, 6 days) OTHER Altitude: 2000 m (maximum) Pollution degree: Overvoltage category: Ingress protection: IP20 front, IP10 back Noise: 0 dB 2-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 51: Type Tests
Insulation: class 1, Pollution degree: 2, Over voltage cat II 1 Not tested by third party. 2.5.13 Production tests THERMAL Products go through an environmental test based upon an Accepted Quality Level (AQL) sampling process. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 2-37...
Page 52: Approvals
Normally, cleaning is not required. When dust has accumulated on the faceplate display, wipe with a dry cloth. To avoid deterioration of electrolytic capacitors, power up units that are stored in a de-energized state once per year, for one hour continuously. 2-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 53: Installation
For any issues, contact GE Grid Solutions as outlined in the For Further Assistance section in chapter 1. Check that you have the latest copy of the F60 Instruction Manual and the UR Family Communications Guide, for the applicable firmware version, at http://gegridsolutions.com/multilin/manuals/index.htm...
Page 54: Panel Cutouts
Maintenance > Change Front Panel. 3.2.1 Horizontal units The F60 is available as a 19-inch rack horizontal mount unit with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains additional user-programmable pushbuttons and LED indicators.
Page 55: Vertical Units
3.2.2 Vertical units The F60 is available as a reduced size (¾) vertical mount unit, with a removable faceplate. The faceplate can be specified as either standard or enhanced at the time of ordering. The enhanced faceplate contains additional user-programmable pushbuttons and LED indicators.
Page 56 PANEL CUTOUTS CHAPTER 3: INSTALLATION Figure 3-4: Vertical dimensions (enhanced panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 57 CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-5: Vertical and mounting dimensions (standard panel) For side-mounting F60 devices with the enhanced front panel, see the following documents available on the UR DVD and the GE Grid Solutions website: • GEK-113180 — UR-Series UR-V Side-Mounting Front Panel Assembly Instructions •...
Page 58 PANEL CUTOUTS CHAPTER 3: INSTALLATION For side-mounting F60 devices with the standard front panel, use the following figures. Figure 3-6: Vertical side-mounting installation (standard panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 59 CHAPTER 3: INSTALLATION PANEL CUTOUTS Figure 3-7: Vertical side-mounting rear dimensions (standard panel) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 60: Rear Terminal Layout
(nearest to CPU module), indicated by an arrow marker on the terminal block. The figure shows an example of rear terminal assignments. Figure 3-8: Example of modules in F and H slots F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 61: Wiring
CHAPTER 3: INSTALLATION WIRING 3.3 Wiring 3.3.1 Typical wiring Figure 3-9: Typical wiring diagram (T module shown for CPU) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 62: Dielectric Strength
3.3.2 Dielectric strength Dielectric strength is the maximum electric strength that can be sustained without breakdown. It is measured in volts. The table shows the dielectric strength of the UR-series module hardware. 3-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 63: Control Power
The power supply module can be ordered for two possible voltage ranges, and the F60 can be ordered with or without a redundant power supply module option. Each range has a dedicated input connection for proper operation. The ranges are as follows (see the Specifications section of chapter 2 for details): •...
Page 64: Ct/Vt Modules
These modules have enhanced diagnostics that can automatically detect CT/VT hardware failure and take the relay out of service. CT connections for both ABC and ACB phase rotations are identical, as shown in the Typical Wiring Diagram. 3-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 65 UR models. Substitute the tilde “~” symbol with the slot position of the module in the following figure. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-13...
Page 66 CT modules must be connected to a ground current source, either a zero-sequence CT (see the Typical wiring diagram with high impedance fault detection earlier in this chapter) or, if a zero-sequence CT is not available, to the neutral conductor of the phase CTs (see diagram below). 3-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 67: Process Bus Modules
3.3.5 Process bus modules The F60 can be ordered with a process bus interface module. The module interfaces with the HardFiber Process Bus System, or HardFiber Brick, allowing bidirectional IEC 61850 fiber optic communications with up to eight HardFiber Bricks.
Page 68: Contact Inputs And Outputs
Form-A contact output with or without a current or voltage monitoring option is not polarity sensitive. The polarity shown in the figure is required for solid-state contact output connection. Figure 3-15: Form-A and solid-state contact outputs with voltage and current monitoring 3-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 69 Output or Terminal Output or assignment input assignment assignment input assignment input Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A Form-C Fast Form-C Form-A Form-A F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-17...
Page 70 2 Inputs Form-A Not Used Form-A ~6a, ~6c 2 Inputs Form-A Solid-State ~7a, ~7c 2 Inputs ~7a, ~7c 2 Inputs Form-A Not Used ~8a, ~8c 2 Inputs ~8a, ~8c 2 Inputs Form-A Solid-State 3-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 71 ~5a, ~5c 2 Inputs 2 Outputs Solid-State Solid-State ~6a, ~6c 2 Inputs 2 Outputs Not Used Not Used ~7a, ~7c 2 Inputs 2 Outputs Solid-State Solid-State ~8a, ~8c 2 Inputs Not Used F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-19...
Page 72 WIRING CHAPTER 3: INSTALLATION Figure 3-16: Contact input and output module wiring (Sheet 1 of 2) 3-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 73 CHAPTER 3: INSTALLATION WIRING Figure 3-17: Contact input and output module wiring (Sheet 2 of 2) For proper functionality, observe the polarity shown in the figures for all contact input and output connections. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-21...
Page 74 The contact inputs with auto-burnish create a high current impulse when the threshold is reached to burn off this oxidation layer as a maintenance to the contacts. Afterwards the contact input current is reduced to a steady-state current. The impulse has a five-second delay after a contact input changes state. 3-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 75: Transducer Inputs And Outputs
Transducer output modules provide DC current outputs in several standard DCmA ranges. Software is provided to configure virtually any analog quantity used in the relay to drive the analog outputs. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-23...
Page 76 (5A, 5C, 5D, 5E, and 5F) and channel arrangements that can be ordered for the relay. Where a tilde “~” symbol appears, substitute the slot position of the module. Figure 3-21: Transducer input/output module wiring The following figure show how to connect RTDs. 3-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 77: Rs232 Faceplate Port
EnerVista UR Setup software provided with the relay. Cabling for the RS232 port is shown in the following figure for both 9-pin and 25-pin connectors. The baud rate for this port can be set, with a default of 115200 bps. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-25...
Page 78: Cpu Communication Ports
Figure 3-23: RS232 faceplate port connection 3.3.9 CPU communication ports 3.3.9.1 Overview In addition to the faceplate RS232 port, there is a rear RS485 communication port. The CPU modules do not require a surge ground connection. 3-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 79 This common voltage is implied to be a power supply common. Some systems allow the shield (drain wire) to be used as common wire and to connect directly to the F60 COM terminal (#3); others function correctly only if the common wire is connected to the F60 COM terminal, but insulated from the shield.
Page 80: Irig-B
IRIG-B is a standard time code format that allows stamping of events to be synchronized among connected devices. The IRIG-B code allows time accuracies of up to 100 ns. Using the IRIG-B input, the F60 operates an internal oscillator with 1 µs resolution and accuracy.
Page 81: Direct Input And Output Communications
UR-series relays with the following connections: UR1-Tx to UR2-Rx, UR2-Tx to UR3-Rx, UR3-Tx to UR4-Rx, and UR4-Tx to UR1-Rx. A maximum of 16 URs can be connected in a single ring. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-29...
Page 82 UR1-Tx1 to UR2-Rx1, UR2-Tx1 to UR3-Rx1, UR3-Tx1 to UR4-Rx1, and UR4-Tx1 to UR1-Rx1 for the first ring; and UR1-Tx2 to UR4-Rx2, UR4-Tx2 to UR3-Rx2, UR3-Tx2 to UR2-Rx2, and UR2-Tx2 to UR1-Rx2 for the second ring. 3-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 83 Those that apply depend on options purchased. The options are outlined in the Inter-Relay Communications section of the Order Code tables in Chapter 2. All of the fiber modules use ST type connectors. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-31...
Page 84: Fiber: Led And Eled Transmitters
The following figure shows the configuration for the 72, 73, 7D, and 7K fiber-laser modules. Figure 3-32: 7x Laser fiber modules The following figure shows configuration for the 2I and 2J fiber-laser modules. 3-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 85: Interface
The following figure shows the typical pin interconnection between two G.703 interfaces. For the actual physical arrangement of these pins, see the Rear Terminal Layout section earlier in this chapter. All pin interconnections are to be maintained for a connection to a multiplexer. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-33...
Page 86 Once the clips have cleared the raised edge of the chassis, engage the clips simultaneously. When the clips have locked into position, the module is inserted fully. 3-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 87 (S1 = ON) and set timing mode to loop timing (S5 = OFF and S6 = OFF). The switch settings for the internal and loop timing modes are shown. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-35...
Page 88 One source lies on the G.703 line side of the interface while the other lies on the differential Manchester side of the interface. Figure 3-39: G.703 dual loopback mode 3-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 89: Rs422 Interface
(data module 1) connects to the clock inputs of the UR RS422 interface in the usual way. In F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-37...
Page 90 Figure 3-42: Timing configuration for RS422 two-channel, three-terminal application Data module 1 provides timing to the F60 RS422 interface via the ST(A) and ST(B) outputs. Data module 1 also provides timing to data module 2 TT(A) and TT(B) inputs via the ST(A) and AT(B) outputs. The data module pin numbers have been omitted in the figure because they vary by manufacturer.
Page 91: Rs422 And Fiber Interface
For the direct fiber channel, address power budget issues properly. When using a laser interface, attenuators can be necessary to ensure that you do not exceed maximum optical input power to the receiver. Figure 3-44: RS422 and fiber interface connection F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-39...
Page 92: And Fiber Interface
Connection — as per all fiber optic connections, a Tx to Rx connection is required The UR-series C37.94 communication module can be connected directly to any compliant digital multiplexer that supports the IEEE C37.94 standard. The figure shows the concept. 3-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 93 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F60 communication for two and three terminal applications.
Page 94 When the clips have locked into position, the module is inserted fully. Figure 3-49: IEEE C37.94 timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. 3-42 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 95: C37.94Sm Interface
Fiber optic cable length — Up to 11.4 km • Fiber optic connector — Type ST • Wavelength — 1300 ±40 nm • Connection — As per all fiber optic connections, a Tx to Rx connection is required F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-43...
Page 96 5.60. For customers using firmware release 5.60 and higher, the module can be identified with "Rev D" printed on the module and is to be used on all ends of F60 communication for two and three terminal applications.
Page 97 When the clips have locked into position, the module is inserted fully. Figure 3-52: C37.94SM timing selection switch setting Modules shipped since January 2012 have status LEDs that indicate the status of the DIP switches, as shown in the following figure. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-45...
Page 98: Activate Relay
Press the right arrow until the message displays. MESSAGE SECURITY Press the down arrow until the message displays. MESSAGE INSTALLATION Press the right arrow until the Not Programmed message displays. MESSAGE RELAY SETTINGS: 3-46 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 99: Install Software
To communicate via the faceplate RS232 port, use a standard straight-through serial cable. Connect the DB-9 male end to the relay and the DB-9 or DB-25 female end to the computer COM2 port as described in the CPU Communication Ports section earlier in this chapter. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-47...
Page 100: System Requirements
This device (catalog number F485) connects to the computer using a straight-through serial cable. A shielded twisted-pair (20, 22, or 24 AWG) connects the F485 converter to the F60 rear communications port. The converter terminals (+, –, GND) are connected to the F60 communication module (+, –, COM) terminals. See the CPU Communication Ports section in chapter 3 for details.
Page 101: Install Software
Click the Next button to begin the installation. The files are installed in the directory indicated, and the installation program automatically creates icons and adds an entry to the Windows start menu. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-49...
Page 102: Add Device To Software
3.7 Add device to software You connect remotely to the F60 through the rear RS485 or Ethernet port with a computer running the EnerVista UR Setup software. The F60 also can be accessed locally with a computer through the front panel RS232 port or the rear Ethernet port using the Quick Connect feature.
Page 103 From the Windows desktop, right-click the My Network Places icon and select Properties to open the network connections window. Or in Windows 7, access the Network and Sharing Center in the Control Panel. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-51...
Page 104 Select the Internet Protocol (TCP/IP) item from the list, and click the Properties button. Click the “Use the following IP address” box. Enter an IP address with the first three numbers the same as the IP address of the F60 relay and the last number different (in this example, 1.1.1.2).
Page 105 Minimum = 0ms, Maximum = 0ms, Average = 0 ms Pinging 1.1.1.1 with 32 bytes of data: verify the physical connection between the F60 and the computer, and double-check the programmed IP address in setting, then repeat step 2. Product Setup  Communications  Network  IP Address...
Page 106 If this computer is used to connect to the Internet, re-enable any proxy server settings after the computer has been disconnected from the F60 relay. Start the Internet Explorer software. Select the UR device from the EnerVista Launchpad to start EnerVista UR Setup. 3-54 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 107 Click the Quick Connect button to open the window. Select the Ethernet interface and enter the IP address assigned to the F60, then click the Connect button. The EnerVista UR Setup software creates a site named “Quick Connect” with a corresponding device also named “Quick Connect”...
Page 108: Configure Serial Connection
For the RS232 connection, a computer with an RS232 port and a serial cable are required. To use the RS485 port at the back of the relay, a GE Grid Solutions F485 converter (or compatible RS232-to-RS485 converter) is required. See the F485 instruction manual for details.
Page 109: Configure Ethernet Connection
SEL-2032. This option enables display of a terminal window to allow interaction with the other device. 11. Click the Read Order Code button to connect to the F60 and upload the order code to the software. If a communications error occurs, ensure that the EnerVista software serial communications values entered in the previous step correspond to the relay setting values, and also ensure that the same IP address is not assigned to multiple F60 ports.
Page 110 12. If using a gateway to connect to the device, select Yes from the drop-down list. 13. Click the Read Order Code button to connect to the F60 device and upload the order code. If the device was entered already, a message displays "Device ’x’ is also using IP address.." If a communications error occurs, ensure that the values entered in the previous steps correspond to the relay setting values, and also ensure that the same IP address is not assigned to multiple F60 ports.
Page 111: Configure Modem Connection
CHAPTER 3: INSTALLATION ADD DEVICE TO SOFTWARE The device has been configured for Ethernet communications. Proceed to the Connect to the F60 section to begin communications. 3.7.4 Configure modem connection A modem connection allows a computer to communicate with a UR device over phone lines.
Page 112: Connect To The F60
When unable to connect because of an "ACCESS VIOLATION," access Device Setup and refresh the order code for the device. When unable to connect, ensure that the same IP address is not assigned to multiple F60 ports, for example under Settings > Product Setup > Communications > Network.
Page 113: Use Quick Connect Via The Front Panel Rs232 Port
Connect a nine-pin to nine-pin RS232 serial cable to the computer and the front panel RS232 port. Verify that the latest version of the EnerVista UR Setup software is installed (available from the GE EnerVista DVD or online from http://www.gegridsolutions.com/multilin). See the software installation section if not already installed.
Page 114: Use Quick Connect Via A Rear Ethernet Port
Connect" and displays them in the Online Window. Expand the sections to view data directly from the F60 device. Use the Device Setup button to change the site name. Each time that the EnerVista software is initialized, click the Quick Connect button to establish direct communications to the F60.
Page 115: Import Settings
If required, change the Files of type drop-down list. Select the file to import. To apply the settings to a live device, drag-and-drop the device entry from the Offline Window area to its entry in the Online Window area. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 3-63...
Page 116 IMPORT SETTINGS CHAPTER 3: INSTALLATION Individual settings also can be dragged and dropped between Online and Offline Window areas. The order codes much match. 3-64 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 117: Interfaces
The EnerVista UR Setup software is provided with every F60. This chapter outlines the EnerVista software interface features. The EnerVista UR Setup Help File also provides details for getting started and using the software interface.
Page 118: Event Viewing
IP Address IP Subnet Mask IP Routing When a settings file is loaded to a F60 that is in-service, the following sequence occurs: The F60 takes itself out of service. The F60 issues a UNIT NOT PROGRAMMED major self-test error.
Page 119: File Support
Settings list / offline window area Software windows, with common tool bar Settings file data view windows, with common tool bar Workspace area with data view tabs Status bar 10. Quick action hot links F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 120: Protection Summary Window
4.1.6 Protection summary window The Protection Summary is a graphical user interface to manage elements, such as enabling and disabling them. Access it under Settings > Protection Summary. See the Settings chapter for information on use. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 121: Settings Templates
Settings file templates simplify the configuration and commissioning of multiple relays that protect similar assets. An example is a substation that has 10 similar feeders protected by 10 UR-series F60 relays. In these situations, typically 90% or greater of the settings are identical among devices. The templates allow engineers to configure and test these common settings, then lock them so that they are not available to users.
Page 122 Figure 4-4: Settings template with all settings specified as locked Specify the settings to make viewable by clicking them. A setting available to view is displayed against a yellow background. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 123 To display only the settings available for editing: Select an installed device or a settings file from the left menu of the EnerVista UR Setup window. Apply the template by selecting the Template Mode > View In Template Mode option. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 124 Once the template has been applied, users are limited to edit the settings specified by the template, but all settings are shown. The effect of applying the template to the phase time overcurrent settings is shown as follows. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 125: Secure And Lock Flexlogic Equations
4.1.8.1 Lock FlexLogic equations To lock individual entries of a FlexLogic equation: Right-click the settings file or online device and select the Template Mode > Create Template item to enable the settings template feature. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 126 The effect of applying the template to the FlexLogic entries is shown here. Figure 4-10: Locking FlexLogic entries through settings templates The FlexLogic entries are also shown as locked in the graphical view and on the front panel display. 4-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 127 Right-click the setting file in the offline window area and select the Edit Device Properties item. The window opens. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-11...
Page 128: Settings File Traceability
When a settings file is transferred to a F60 device, the date, time, and serial number of the F60 are sent back to EnerVista UR Setup and added to the settings file on the local computer. This information can be compared with the F60 actual values at any later date to determine if security has been compromised.
Page 129 With respect to the figure, the traceability feature is used as follows. The transfer date of a settings file written to a F60 is logged in the relay and can be viewed in the EnerVista software or the front panel display. Likewise, the transfer date of a settings file saved to a local computer is logged in the EnerVista software.
Page 130 4.1.9.2 Online device traceability information The F60 serial number and file transfer date are available for an online device through the actual values. Select the Actual Values > Product Info > Model Information menu item within the EnerVista online window as shown in the example.
Page 131: Front Panel Interface
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel. To view the front panel in EnerVista software: Click Actual Values > Front Panel. Figure 4-18: Front panel use in the software (C60 shown) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-15...
Page 132: Front Panel Keypad
MESSAGE arrow from a header display displays specific information for the category. Conversely, continually pressing the MESSAGE left arrow from a setting value or actual value display returns to the header display. 4-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 133: Changing Settings
Each numerical setting has its own minimum, maximum, and increment value associated with it. These parameters define what values are acceptable for a setting. FLASH MESSAGE For example, select the SETTINGS  PRODUCT SETUP  DISPLAY PROPERTIES  FLASH TIME: 10.0 s MESSAGE TIME setting.  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-17...
Page 134 Repeat step 2 for the remaining characters: r,e,a,k,e,r, ,#,1. Press to store the text. ENTER If you have any problem, press to view context sensitive help. Flash messages appear sequentially for several HELP 4-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 135: Faceplate
The faceplate is hinged to allow easy access to the removable modules. There is also a removable dust cover that fits over the faceplate that must be removed in order to access the keypad panel. The following figure shows the horizontal arrangement of the faceplate panel. Figure 4-21: Standard horizontal faceplate F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-19...
Page 136: Led Indicators
LED indicator or target message, once the condition has been cleared (these RESET latched conditions can also be reset via the menu). SETTINGS  INPUT/OUTPUTS  RESETTING keys are used by the breaker control feature. USER 4-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 137 Support for applying a customized label beside every LED is provided. Default labels are shipped in the label package of every F60, together with custom templates. The default labels can be replaced by user-printed labels. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 138 ORed to turn on or off the phase A, B, or C LEDs. • VOLTAGE — Indicates voltage was involved • CURRENT — Indicates current was involved • FREQUENCY — Indicates frequency was involved 4-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 139 LED settings must be entered as shown in the User-programmable LEDs section of chapter 5. The LEDs are fully user-programmable. The default labels can be replaced by user-printed labels for both panels as explained in the next section. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-23...
Page 140: Custom Led Labeling
Select the Front Panel Label Designer item from the Online Window or Offline Window area, for example under Settings > Front Panel Label Designer. If the option does not display, it means that the F60 does not have an enhanced front panel or that no customization is possible. The Online Window has the advantage of displaying the live fields as opposed to blank fields.
Page 141 Use the tool EXACTLY as outlined as follows, with the printed side containing the GE part number facing the user. The label package shipped with every F60 contains the three default labels, the custom label template sheet, and the label removal tool.
Page 142 Bend the tab at the center of the tool tail as shown. To remove the LED labels from the F60 enhanced front panel and insert the custom labels: Use the knife to lift the LED label and slide the label tool underneath. Ensure that the bent tabs are pointing away from the relay.
Page 143 Slide the new LED label inside the pocket until the text is properly aligned with the LEDs, as shown. To remove the user-programmable pushbutton labels from the F60 enhanced front panel and insert the custom labels: Use the knife to lift the pushbutton label and slide the tail of the label tool underneath, as shown. Ensure that the bent F60 FEEDER PROTECTION SYSTEM –...
Page 144 Remove the tool and attached user-programmable pushbutton label. Slide the new user-programmable pushbutton label inside the pocket until the text is properly aligned with the 4-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 145: Breaker Control
4.2.9 Breaker control The F60 can interface with associated circuit breakers. In many cases the application monitors the state of the breaker, that can be presented on faceplate LEDs, along with a breaker trouble indication. Breaker operations can be manually initiated from the faceplate keypad or automatically initiated from a FlexLogic operand.
Page 146: Change Passwords
When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 147: Invalid Password Entry
By default, when an incorrect Command or Setting password has been entered via the faceplate interface three times within five minutes, the FlexLogic operand is set to “On” and the F60 does not allow settings or LOCAL ACCESS DENIED command level access via the faceplate interface for five minutes.
Page 148: Logic Diagrams
Not. Negates/reverses the output, for example 0 becomes 1.  Connection  S, R Set, Reset Timer pickup. Triggered by the settings latch in the diagram. Timer reset. Triggered by the reset latch in the diagram. 4-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 149: Flexlogic Design And Monitoring Using Engineer
Works with all UR firmware versions The figure shows an example where several inputs are used to trigger an output. With the OR function, any one of the inputs can trigger the output. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-33...
Page 150 This section explains how to use Engineer. It outlines the following topics: • Design logic • Send file to and from device • Monitor logic • View front panel • Generate connectivity report • Preferences 4-34 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 151: Design Logic
Preparation — Under Settings > Inputs/Outputs > Virtual Outputs, virtual outputs 3 and 4 are named DLTrigger Top logic — Seven-minute timer trigger Bottom logic — Turn on LED 9 for 10 seconds when the trigger starts F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-35...
Page 152 This procedure uses input / output logic as an example. To create a logic diagram: In the Offline Window area, access Engineer for the device, then Logic Designer. If the device is not listed, right-click 4-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 153 Add the input blocks to the logic diagram. For example, click the I/O Tokens tab on the right, click the Input element, then click in the logic sheet to add it. Or drag-and-drop it. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-37...
Page 154 Line option. The cursor needs to be at the connection point to end the line, not elsewhere on the block. Note that the outline color is no longer red on the blocks. 4-38 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 155 The warning "input using disabled feature" means that input needs to be enabled. Double-click the block, click the View Associated Screen button, enable the setting, save, and recompile. The output and messages are explained in the next section. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-39...
Page 156 'Do not update IID file when updating SCL files') are updated. If the CID file is not already there, it is generated. The location of these files is C:\ProgramData\GE Power Management\urpc, for example, in the Offline and Online folders.
Page 157 The same timer is used in more than one place in the editor. This means (TIMER_ID, SheetReference) either the circuit that the Timer belongs to has been branched, or the Timer has been duplicated. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-41...
Page 158 Click the Ok button to save and exit from the window. In the logic diagram, select an element, then click in the drawing area to add it, click again to add a second box, and so on. 4-42 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 159 Optimization Summary. Changes also display when the FlexLogic Equation Editor is accessed. The logic diagram does not change. In the example shown, no lines were saved to free up space. Figure 4-45: Code optimization results F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-43...
Page 160 Type in the second text string box, or select any of the 32 previous searches from the drop-down list. Click the Search button. Any results display. The search applies to all tabs, not just the active tab. Double-click a search result to view the item. 4-44 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 161: Send File To And From Device
When a window opens, select the device to which you want to send the file, then click the Send button and confirm. The order codes must match. The file is sent to the live device. Any errors can be viewed in the log file at the prompt. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-45...
Page 162: Monitor Logic
(green box outline). In this case, the battery is weak and needs to be replaced. This can be viewed as the Replace Battery message on the front panel of the device and in the EnerVista software under Actual Values > Front Panel > Front Panel or Display/Keypad. 4-46 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 163: View Front Panel And Print Labels
To save the report and labels, click File > Save As, enter a file name, and select the FPR, JPG, or PDF format. Use the instructions in the second tab of the window to add the labels to the physical device. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-47...
Page 164: Generate Connectivity Report
View > Toolbar > Advanced Actions — Active when in Logic Designer. Toggles a toolbar to nudge, rotate, flip, or change the order of an element. View > Show Unused Pins — Enable to display unconnected pins. Disable to eliminate unconnected pins from the view, for example when printing. 4-48 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 165 File Information The text entered here displays at the bottom right of a diagram when printing, provided that the Show Title Block option is enabled. Note the option to change the logo from the GE logo to your company logo. Display The panel sets how the element boxes display.
Page 166 The software displays the color specified when an element is on. There is no color when the element is off. The software displays another color when the status cannot be determined and is unknown. 4-50 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 167 Options display for filtering, such as recording timing for Virtual Inputs and Outputs, but not Communications Status. 4.4.6.4 COMTRADE waveforms Waveform files are viewable in the EnerVista software. The preferences are unrelated to Engineer and are outlined in the UR Family Communications Guide. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-51...
Page 168: Toolbars
When you re-launch the EnerVista software, communication is on by default. 4.4.7.2 Token Toolbox Drawing Tools Draw a line. Click and drag to draw. Draw multiple joined lines. Click and drag for each line. Double-click to finish. 4-52 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 169 Remote inputs from other devices Input from another UR device. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. Teleprotection inputs/outputs and direct inputs/outputs are mutually exclusive and cannot be used simultaneously. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-53...
Page 170 Tag-In can is used to reference an existing Tag-Out. It joins another diagram to a previous diagram. Boolean Tokens These symbols are used to create FlexLogic Equations. Use them as intermediate logic for the Virtual Output equations. The display can vary from that shown here. 4-54 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 171 Place a positive one shot and a negative one shot symbol in the Logic Designer diagram Place a timer in the Logic Designer diagram Elements These blocks configure properties of the element or use element operands as input to FlexLogic equations. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-55...
Page 172 Set the width of the selected components to the same width as the reference component Same Height Set the height of the selected components to the same height as the reference component 4-56 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 173 Front, Back Moves current components to the absolute front or back of all viewable layers Forward, Backward Moves current components on layer higher or lower than its original layer hierarchy F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 4-57...
Page 174 FLEXLOGIC DESIGN AND MONITORING USING ENGINEER CHAPTER 4: INTERFACES 4-58 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 175: Settings
See page 5-99    OSCILLOGRAPHY See page 5-101    DATA LOGGER See page 5-103    DEMAND See page 5-105    USER-PROGRAMMABLE See page 5-106   LEDS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 176  SETTINGS  SETTING GROUP 1 See page 5-192   GROUPED ELEMENTS   SETTING GROUP 2     SETTING GROUP 3    SETTING GROUP 4   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 177 See page 5-322    DIRECT OUTPUTS See page 5-322    TELEPROTECTION See page 5-326     SETTINGS  DCMA INPUTS See page 5-328   TRANSDUCER I/O  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 178: Overview
VT ratio setting is set to the nominal ratio of the VTs and the secondary voltage setting is set to the phase-to-phase voltage seen by the relay when the voltage of the protected system in nominal. The UR uses the convention that nominal voltages in a three-phase system are phase-to-phase voltages. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 179 Not every operand of a given element in a UR relay generates events, only the major output operands. Elements, asserting output per phase, log operating phase output only, without asserting the common three-phase operand event. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 180: Introduction To Ac Sources
For example, in the scheme shown in the preceding figure, the user configures one source to be the sum of CT1 and CT2 and can name this source as “Wdg1 I.” F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 181: Product Setup
(as described earlier) as follows for a maximum configuration: F1, F5, M1, M5, U1, and U5. 5.3 Product setup 5.3.1 Security 5.3.1.1 Security overview The following security features are available: • Password security — Basic security present by default F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 182 To reset the unit after a lost password: Email GE customer service at multilin.tech@ge.com with the serial number and using a recognizable corporate email account. Customer service provides a code to reset the relay to the factory defaults.
Page 183 When entering a settings or command password via EnerVista or any serial interface, the user must enter the corresponding connection password. If the connection is to the back of the F60, the remote password must be used. If the connection is to the RS232 port of the faceplate, the local password must be used.
Page 184 When an original password has already been used, enter it in the Enter Password field and click the Send Password to Device button. Re-enter the password in the Confirm Password field. 5-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 185 INVALID ATTEMPTS BEFORE LOCKOUT The F60 provides a means to raise an alarm upon failed password entry. If password verification fails while accessing a password-protected level of the relay (either settings or commands), the FlexLogic operand is UNAUTHORIZED ACCESS asserted.
Page 186 ACCESS AUTH TIMEOUT immediately denied. If access is permitted and an off-to-on transition of the FlexLogic operand is detected, the timeout is restarted. The status of this timer updates every five seconds. 5-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 187 It is disabled by default to allow access to the device immediately after installation. When security is disabled, all users have administrator access. GE recommends enabling the EnerVista security before placing the device in service. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 188 If you force password entry by using this feature, ensure that you know the Administrator password. If you do not know the password and are locked out of the software, contact GE Grid Solutions for the default password of a UR device.
Page 189 The EnerVista security management system must be enabled (the Enable Security check box enabled) To modify user privileges: Select the Security > User Management item from the top menu to open the user management window. Locate the username in the User field. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-15...
Page 190 This feature requires a CyberSentry software option. See the Order Codes section in chapter 2 for details. The EnerVista software provides the means to configure and authenticate the F60 access using either a server or the device. Access to functions depends on user role.
Page 191 When the "Device" button is selected, the F60 uses its local authentication database and not the RADIUS server to authenticate the user. In this case, it uses built-in roles (Administrator, Engineer, Supervisor, Operator, Observer, or Administrator and Supervisor when Device Authentication is disabled), as login accounts and the associated passwords are stored on the F60 device.
Page 192 Figure 5-3: Security panel when CyberSentry installed For the Device > Settings > Product Setup > Supervisory option, the panel looks like the following. Figure 5-4: Supervisory panel For the Security panel, the following settings are available. 5-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 193 Administrator is to re-enable Device authentication when Device authentication is disabled. To re-enable Device authentication, the Supervisor unlocks the device for setting changes, and then the Administrator can re- enable Device authentication. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-19...
Page 194 LOGIN: Range: Administrator, Engineer, Supervisor,   None Operator, Factory (for factory use only), None  CHANGE LOCAL See page 5-21   PASSWORDS  SESSION See page 5-22   SETTINGS 5-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 195 • Observer — This role has read-only access to all F60 settings. This role allows unlimited concurrent access but it has no download access to any files on the device. Observer is the default role if no authentication has been done to the device.
Page 196 In Device authentication mode, the Observer role does not have a password associated with it. In Server authentication mode the Observer role requires a password. If you are locked out of the software, contact GE Grid Solutions for the default password. When using CyberSentry, the default password is "ChangeMe1#".
Page 197 SETTINGS  PRODUCT SETUP  SECURITY  SUPERVISORY  SELF TESTS  SELF TESTS  FAILED See below    AUTHENTICATE FIRMWARE LOCK: Range: Enabled, Disabled  Enabled SETTINGS LOCK: Range: Enabled, Disabled  Enabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-23...
Page 198 After making any required changes, log out. When changing settings offline, ensure that only settings permitted by the role that performs the settings download are changed because only those changes are applied. 5-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 199 Clear Energy command (not applicable to all UR products) Clear Unauthorized Access command Clear Teleprotection Counters command (not applicable to all UR products) Clear All Relay Records command Role Log in Role Log off F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-25...
Page 200: Display Properties
PRODUCT SETUP CHAPTER 5: SETTINGS In addition to supporting syslog, a F60 with CyberSentry also saves the security events in two local security files, these being SECURITY_EVENTS.CSV and SETTING_CHANGES.LOG. Details on these files and how to retrieve them are available in the EnerVista software under Maintenance >...
Page 201 Some customers prefer very low currents to display as zero, while others prefer the current to display even when the value reflects noise rather than the actual signal. The F60 applies a cut-off value to the magnitudes and angles of the measured currents.
Page 202: Clear Relay Records
Selected records can be cleared from user-programmable conditions with FlexLogic operands. Assigning user- programmable pushbuttons to clear specific records is a typical application for these commands. Since the F60 responds to rising edges of the configured FlexLogic operands, they must be asserted for at least 50 ms to take effect.
Page 203: Communications
Range: 0 to 1000 ms in steps of 10  MIN TIME: 0 ms , and — The F60 is equipped with two independent serial communication RS232 BAUD RATE RS485 COM2 BAUD RATE PARITY ports. The faceplate RS232 port is intended for local use and has two options for baud rate. The rear COM2 port is RS485 and has settings for baud rate and parity.
Page 204 5.3.4.3 Ethernet network topology The F60 has three Ethernet ports. Each Ethernet port must belong to a different network or subnetwork. Configure the IP address and subnet to ensure that each port meets this requirement. Two subnets are different when the bitwise AND operation performed between their respective IP address and mask produces a different result.
Page 205 SCADA is provided through LAN2. P2 and P3 are connected to LAN2, where P2 is the primary channel and P3 is the redundant channel. In this configuration, P3 uses the IP and MAC addresses of P2. Figure 5-6: Multiple LANs, with redundancy F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-31...
Page 206 IP addresses and mask. Configure the network IP and subnet settings before configuring the routing settings. To obtain a list of all port numbers used, for example for audit purposes, contact GE technical support with substantiating information, such as the serial number and order code of your device.
Page 207 2 is performed. The delay in switching back ensures that rebooted switching devices connected to the F60, which signal their ports as active prior to being completely functional, have time to completely initialize themselves and become active. Once port 2 is active again, port 3 returns to standby mode.
Page 208 UR 7 redundancy Failover is selected for redundancy. 5.3.4.6 Parallel Redundancy Protocol (PRP) The F60 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 209 Host routes are not supported at present. The routing table configuration is available on the serial port and front panel. This is a deliberate decision, to avoid loss of connectivity when remotely configuring the F60. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-35...
Page 210 Starting with UR 7.10, up to six static network routes can be configured in addition to a default route. The default route configuration was also moved from the network settings into the routing section. The figure shows an example of topology that benefits from the addition of static routes. 5-36 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 211 EnerVista. Show routes and ARP tables This feature is available on the Web interface, where the main menu contains an additional Communications menu and two submenus: • Routing Table • ARP Table F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-37...
Page 212 0 disables Modbus over TCP/IP, meaning closes the Modbus TCP port. When the port number is changed to 0, the change takes effect when the F60 is restarted. When it is set to 0, use the front panel or serial port to communicate with the relay.
Page 213 SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP PROTOCOL  DNP CHANNELS See below    DNP ADDRESS: Range: 0 to 65535 in steps of 1   DNP NETWORK See below   CLIENT ADDRESSES F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-39...
Page 214 Range: 1, 2, 5, 6  DEFAULT VARIATION: 1 DNP OBJECT 21 Range: 1, 2, 9, 10  DEFAULT VARIATION: 1 DNP OBJECT 22 Range: 1, 2, 5, 6  DEFAULT VARIATION: 1 5-40 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 215 DNP ADDRESS unique address to each DNP slave. The F60 can specify a maximum of five clients for its DNP connections. These are IP addresses for the controllers to which the F60 can connect. The settings follow. SETTINGS  PRODUCT SETUP  COMMUNICATIONS  DNP PROTOCOL  DNP NETWORK CLIENT ADDRESSES ...
Page 216 DNP TCP connection for greater than the time specified by this setting, the connection is aborted by the F60. This frees up the connection to be re-used by a client. Any change takes effect after cycling power to the relay.
Page 217 60870-5-104 point lists must be in one continuous block, any points assigned after the first “Off” point are ignored. 5.3.4.12 IEC 61850 protocol The F60 is provided with optional IEC 61850 communications. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 218 The maximum number of simultaneous clients supported by the UR family is five. EnerVista setup for IEC 61850 The EnerVista UR Setup software provides the interface to configure F60 settings for the IEC 61850 protocol. This section describes this interface. The software also supports import/export and merging of IEC 61850 Substation Configuration Language (SCL) files as documented in the UR Family Communications Guide.
Page 219 Figure 5-11: IEC 61850 panel Opening the IEC 61850 window while online causes the UR Setup software to retrieve and import an SCL file from the F60. This System Configuration Description (SCD) file contains all the settings in the UR at the time of the file request, both those that are mapped into the IEC 61850 information model (that is, the "public"...
Page 220 When the Save button is clicked in the online IEC 61850 window, UR Setup software prepares a configured IED description (CID) file containing all the settings of the UR and sends the CID file to the F60. Upon receipt, the F60 checks the CID file for correctness, going out of service, then back into service when the CID file is accepted.
Page 221 Default: TEMPLATE The value entered sets the IED name used by IEC 61850 for the F60. An IED name unique within the network must be entered for proper operation. Valid characters are upper and lowercase letters, digits, and the underscore (_) character.
Page 222 Range: status-only, direct-with-normal-security, sbo-with-normal-security Default: sbo-with-normal-security This setting specifies the control service that clients must use to control the TEST MODE FUNCTION of the F60. An "on" control to <LDName>/LLN0.Mod changes TEST MODE FUNCTION to Disabled, an "on-blocked" control changes it to Forcible, and a "test/blocked"...
Page 223 Protection logical device has been set to instance name "Prot", the function-related name "Feeder1Prot" and the configuration revision "2016-03-07 08:46." The text is clipped on the right if the line is longer than the available width. The next paragraphs explain how to do this setup. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-49...
Page 224 Figure 5-15: Menu for logical node If the insert option is selected, or the edit option is selected for other than the Master logical device, a logical device parameters edit dialog opens. 5-50 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 225 Each logical device inst name is required to be unique within the device, and it cannot be blank. Also, if the corresponding functional ldName setting is blank, the concatenation of the IED name and the logical device F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-51...
Page 226 The UR increments the value of paramRev by one whenever one or multiple setting changes occurs in one Modbus write request by any means (front panel, Modbus, or MMS) other than by SCL file 5-52 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 227 Routable GOOSE (R-GOOSE) is supported in firmware release 7.4 and later. Routable GOOSE allows UR and other devices to be located in separate networks. Encryption/decryption of messages is performed by a separate gateway device. Messages are routed using a separate router, using IP addresses. Note the following behavior: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-53...
Page 228 The UR does not implement the Fixed-Length encoded GOOSE messages option specified in IEC 61850-8-1:2011 clause A.3; the UR always uses the ASN.1 Basic encoding rules (as specified in ISO/IEC 8825-1) as specified in IEC 61850 edition 1.0 and as optional in IEC 61850 edition 2.0. 5-54 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 229 TxGOOSE1 messages from other GOOSE messages. <LDName> is a syntactic variable that is set to the value of setting Master functional ldName if one or more characters have been entered to that setting, otherwise the value of setting IED NAME suffixed with "Master". F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-55...
Page 230 Network devices can forward a message with a higher priority value before a message with a lower priority value, which speeds delivery of high-priority messages in heavily loaded networks. The standard recommends that higher-priority messages, such as GOOSE, have priority values in the range of 4 to 7. 5-56 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 231 Range: 1 to 60 s in steps of 1 s Default: 60 s This setting specifies the time interval between heartbeat messages, meaning messages that are sent periodically while no events are detected. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-57...
Page 232 61850-90-5 R GOOSE service can be subscribed to. The UR accepts both the variable length encoded GOOSE messages specified IEC 61850 8 1:2004 and the Fixed-Length encoded GOOSE messages as specified in IEC 61850 8 1:2011 clause A.3. 5-58 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 233 RxGOOSE1 message. If the entered value is the empty string, RxGOOSE1 does not check the value received in the goID field. If the publisher is a UR 7.3x series device, this setting needs match the value of the publisher's TxGOOSE GoID setting. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-59...
Page 234 <GoCBName> is the name of the publishing control block. The F60 translates the ACSI format required for this setting to the MMS format used in GOOSE messages: <LDName>/LLN0$GO$<GoCBName> If the publisher is a UR 7.3x or 7.40 series device, <LDName> is the value of the publisher's Master functional ldName setting if that setting is not empty, otherwise it is the value of the publisher's IED NAME suffixed with "Master".
Page 235 If the publisher is a UR 7.3x or 7.40 series device, set these settings to match the basic type of the members of the publisher's data set selected by the publisher's TxGOOSE datSet setting. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-61...
Page 236 SCD (supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. The figure shows a selection being made by importing a CID file using the Add IED function. 5-62 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 237 This setting selects the logic state for the RxGOOSE Boolean1 FlexLogic operand if the UR has just completed startup and the selected RxGOOSE has not yet received a message, or the selected RxGOOSE has lost its connectivity with the publisher. The following choices are available: F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-63...
Page 238 Range: None, RxGOOSE1, RxGOOSE2, and so on Default: None This setting selects the GOOSE message containing the value that drives the RxGOOSE DPS1 FlexLogic operand. If set to None, the RxGOOSE DPS1 FlexLogic operand assumes its default state. 5-64 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 239 (supported in version 7.40 and later). When the file format is SCD, the system lists all IEDs inside the SCD file and lets the user select the ones to add. Figure 5-23: RxGOOSE Analog Inputs panel There are 32 RxGOOSE analog inputs. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-65...
Page 240 Range: 0.000 to 1000000000.000 in steps of 0.001 Default: 1.000 This setting specifies the per-unit base value for other F60 features to use with the RxGOOSE Analog1 operand. A FlexElement for instance subtracts two quantities after converting their values to integers rescaled to a common base, the common base being the largest of the base values of the two quantities.
Page 241 RptEna attribute is false. Buffered and unbuffered reports Navigate to Settings > Product Setup > Communications > IEC 61850 > Reports > Buffered Reports or Unbuffered Reports. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-67...
Page 242 Also, the control block can be configured to send integrity reports containing the present value of all members either on demand from the client or periodically. A TCP handshaking mechanism causes messages that are not read and acknowledged by the client to be retransmitted. 5-68 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 243 Control blocks and data sets can be pre-configured by sending the F60 a CID file. See the UR Family Communications Guide for details. EnerVista UR Setup also can be used to select the data set members and to pre-configure the control blocks.
Page 244 This setting selects the data set whose members' status is reported in Unbuffered Report1 messages using the UR Setup software designator for the data set. The IEC 61850 name of the data sets are configured in the Datasets panel, as described later. 5-70 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 245 DataSets Navigate to Settings > Product Setup > Communications > IEC 61850 > DataSets. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-71...
Page 246 The DataSet name is not copied or pasted. In short, use this feature to copy a DataSet Member setting and paste it into another Member setting, a text file, or Word, as examples. 5-72 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 247 Select the member from the drop-down list. Or right-click an entry to copy, paste, delete, or insert. Product setup Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-73...
Page 248 Deadband parameters of measured values related to the Energy metering are configured here. Real Time Clock Navigate to Settings > Product Setup > Communications > IEC 61850 > Product Setup > Real Time Clock. 5-74 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 249 However, a tabulation of the analog values and their associated deadband setting can be found in the UR Family Communications Guide. Figure 5-30: Deadband settings with .db suffix F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-75...
Page 250 Navigate to Settings > Communications > IEC 61850 > System Setup > Breakers > Breaker 1 to access the settings that configure the IEC 61850 protocol interface with the first breaker control and status monitoring element. The settings and functionality for the others are similar. 5-76 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 251 SelectWithValue or Operate service with ctlVal true and with Check.Interlock-check true is requested of either BkrCSWI1.Pos or Bkr0XCBR1.Pos and the selected operand is not activated, a Negative Response (-Rsp) is issued with the REASON CODE of Blocked-by-interlocking. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-77...
Page 252 This setting specifies the maximum time between an operate command to breaker 1 via BkrCSWI1.Pos until BkrCSWI1.Pos.stVal enters the commanded state. The command terminates if the commanded state is not reached in the set time. 5-78 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 253 If a SelectWithValue or Operate service with ctlVal true and with Check.Interlock-check true is requested of DiscCSWI1.Pos or Disc0XSWI1.Pos and the selected operand is not activated, a Negative Response (-Rsp) is issued with the REASON CODE of Blocked-by-interlocking. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-79...
Page 254 > System Setup section later. These signals force a disconnect switch trip or close control while the operand selected by setting XSWI1 ST.LOC OPERAND is not active. "sbo" here is select-before-operate. Enhanced security means that the F60 reports to the client the disconnect switch 1 position the end of the command sequence.
Page 255 Navigate to Settings > Product Setup > Communications > IEC 61850 > Settings for Commands to access the settings that configure the IEC 61850 protocol interface for record clear commands. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-81...
Page 256 This setting selects the control model clients must use to successfully control the command CLEAR FAULT REPORTS. "sbo" here is select-before-operate. Enhanced security means that the F60 reports to the client the breaker 1 position at the end of the command sequence.
Page 257 Virtual Inputs are controllable FlexLogic operands that can be controlled via IEC 61850 commands to GGIO2, by DNP, by Modbus, and by the UR front panel. The settings related to these IEC 61850 commands are described here. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-83...
Page 258 Navigate to Settings > Product Setup > Communications > IEC 61850 > GGIO > GGIO4 > GGIO4.AnIn1 to access the settings for the first GGIO4 value. The settings and functionality for the others are similar. 5-84 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 259 <LDName>/GGIO4.AnIn01.instMag.f. This setting is stored as an IEEE 754 / IEC 60559 floating point number. Because of the large range of this setting, not all possible values can be stored. Some values are rounded to the closest possible floating point number. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-85...
Page 260 CHAPTER 5: SETTINGS File transfer by IEC 61850 The F60 supports file transfer by IEC 61850. The approach is as follows, using the SISCO AX-S4 61850 client software as an example. In the AX-S4 61850 Explorer window, click the Tools menu and access the SISCO File Transfer Utility.
Page 261 NUMBER: 0 The Trivial File Transfer Protocol (TFTP) can be used to transfer files from the F60 over a network. The F60 operates as a TFTP server. TFTP client software is available from various sources, including Microsoft Windows NT. The dir.txt file obtained from the F60 contains a list and description of all available files, for example event records and oscillography.
Page 262 0.0.0.0 The F60 can specify a maximum of five clients for its IEC 104 connections. These are IP addresses for the controllers to which the F60 can connect. A maximum of two simultaneous connections are supported at any given time.
Page 263 Modbus register address. The default setting value of “0” is considered invalid. Fast exchanges (50 to 1000 ms) are generally used in control schemes. The F60 has one fast exchange (exchange 1) and two slow exchanges (exchange 2 and 3).
Page 264 EXCH 1 DATA ITEM 1 to 20/50 from the F60 memory map can be configured to be included in an EGD exchange. The settings are the starting Modbus register address for the data item in decimal format. See the Modbus memory map in the UR Series Communications Guide for details.
Page 265 PTP, or SNTP, its time is overwritten by these three sources, if any of them is active. If the synchronization timeout occurs and none of IRIG-B, PTP, or SNTP is active, the F60 sets the invalid bit in the time stamp of a time-tagged message.
Page 266 Range: -32768 to 32767 in steps of 1  OFFSET: 0  ASDU 4 ANALOG 9 Range: FlexAnalog parameter  ASDU 4 ANALOG 9 Range: 0.000 to 65.535 in steps of 0.001  FACTOR: 1.000 5-92 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 267 FlexAnalog operands. The measurands sent are voltage, current, power, power factor, and frequency. If any other FlexAnalog is chosen, the F60 sends 0 instead of its value. Note that the power is transmitted in KW, not W. Measurands are transmitted as ASDU 3 or ASDU 9 (type identification value set to measurands I, respectively measurands II).
Page 268 Commands are received as General Command (Type Identification 20). The user can configure the action to perform when an ASDU command comes. A list of available mappings is provided on the F60. This includes 64 virtual inputs (see the following table). The ON and OFF for the same ASDU command can be mapped to different virtual inputs.
Page 269: Modbus User Map
ADDRESS The UR Family Communications Guide outlines the Modbus memory map. The map is also viewable in a web browser; enter the IP address of the F60 in a web browser and click the option. 5.3.6 Real-time clock 5.3.6.1 Menu SETTINGS ...
Page 270 Setup for IRIG-B is illustrated in the Installation chapter. For the Other protocols, whenever a time synchronization message is received through any of the active protocols, the F60 clock updates. However, given that IEC 60870-5-103, IEC 60870-5-104, Modbus, and DNP are low-accuracy time synchronization methods, avoid their use for synchronization when better accuracy time protocols, such as IRIG-B and PTP, are active in the system.
Page 271 CHAPTER 5: SETTINGS PRODUCT SETUP The F60 supports the Precision Time Protocol (PTP) specified in IEEE Std 1588 2008 using the Power Profile (PP) specified in IEEE Std C37.238 2011. This enables the relay to synchronize to the international time standard over an Ethernet network that implements PP.
Page 272 F60 clock is closely synchronized with the SNTP/ NTP server. It takes up to two minutes for the F60 to signal an SNTP self-test error if the server is offline.
Page 273: Fault Reports
 2:00 The F60 maintains two times: local time and Universal Coordinated Time (UTC). Local time can be provided by IRIG-B signals. UTC time is provided by SNTP servers. The real-time clock (RTC) and time stamps reported in historical records and communication protocols can be incorrect if the Local Time settings are not configured properly.
Page 274 MAG: 0.00 Ω The F60 relay supports one fault report and an associated fault locator per CT bank to a maximum of three. The signal source and trigger condition, as well as the characteristics of the line or feeder, are entered in this menu.
Page 275: Oscillography
(grounded loads, reactors, zig-zag transformers, shunt capacitor banks, and so on). 5.3.8 Oscillography 5.3.8.1 Menu SETTINGS  PRODUCT SETUP  OSCILLOGRAPHY  OSCILLOGRAPHY NUMBER OF RECORDS: Range: 1 to 64 in steps of 1   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-101...
Page 276 64 samples per cycle. That is, it has no effect on the fundamental calculations of the device. When changes are made to the oscillography settings, all existing oscillography records are cleared. 5-102 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 277: Data Logger
Analog channel 23 ↔ 25th harmonic 5.3.9 Data logger SETTINGS  PRODUCT SETUP  DATA LOGGER  DATA LOGGER DATA LOGGER MODE: Range: Continuous, Trigger  Continuous  DATA LOGGER TRIGGER: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-103...
Page 278 This setting only applies when the mode is set to “Trigger.” — This setting selects the time interval at which the actual value data is recorded. DATA LOGGER RATE 5-104 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 279: Demand
The figure shows the 90% thermal response time characteristic of 15 minutes. A setpoint establishes the time to reach 90% of a steady-state value, just as the response time of an analog instrument. A steady state value applied for twice the response time indicates 99% of the value. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-105...
Page 280: User-Programmable Leds
1 state. The trip and alarm LEDs on panel 1 can also be customized in a similar manner. To ensure correct functionality of all LEDs, an LED test feature is also provided. 5-106 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 281 The test responds to the position and rising edges of the control input defined by the LED TEST CONTROL setting. The control pulses must last at least 250 ms to take effect. The following diagram explains how the test is executed. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-107...
Page 282 2. When stage 2 is completed, stage 3 starts automatically. The test can be cancelled at any time by pressing the pushbutton. 5-108 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 283 AR ENABLED LED 10 operand BREAKER 1 CLOSED LED 22 operand AR DISABLED LED 11 operand BREAKER 1 TROUBLE LED 23 operand AR RIP LED 12 operand LED 24 operand AR LO F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-109...
Page 284: User-Programmable Self-Tests
There are three standard control pushbuttons, labeled USER 1, USER 2, and USER 3, on the standard and enhanced front panels. These are user-programmable and can be used for various applications such as performing an LED test, switching setting groups, and invoking and scrolling though user-programmable displays. 5-110 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 285 The location of the control pushbuttons are shown in the following figures. Figure 5-43: Control pushbuttons (enhanced faceplate) An additional four control pushbuttons are included on the standard faceplate when the F60 is ordered with the 12 user- programmable pushbutton option.
Page 286: User-Programmable Pushbuttons
Range: 0 to 60.00 s in steps of 0.05  TIME: 0.00 s PUSHBTN 1 LED CTL: Range: FlexLogic operand  PUSHBTN 1 MESSAGE: Range: Disabled, Normal, High Priority  Disabled PUSHBUTTON 1 Range: Disabled, Enabled  EVENTS: Disabled 5-112 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 287 CHAPTER 5: SETTINGS PRODUCT SETUP The F60 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. User-programmable pushbuttons provide an easy and error-free method of entering digital state (on, off) information. The number of available pushbuttons is dependent on the faceplate module ordered with the relay.
Page 288 “Self-reset” as the pushbutton operand status is PUSHBUTTON 1 FUNCTION implied to be “Off” upon its release. The length of the “Off” message is configured with the PRODUCT SETUP  DISPLAY setting. PROPERTIES  FLASH MESSAGE TIME 5-114 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 289 “High Priority” or “Normal.” MESSAGE — If this setting is enabled, each pushbutton state change is logged as an event into the event PUSHBUTTON 1 EVENTS recorder. The figures show the user-programmable pushbutton logic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-115...
Page 290 PRODUCT SETUP CHAPTER 5: SETTINGS Figure 5-48: User-programmable pushbutton logic (Sheet 1 of 2) 5-116 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 291: Flex State Parameters
16 states are readable in a single Modbus register. The state bits can be configured so that all states of interest are available in a minimum number of Modbus registers. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-117...
Page 292: User-Definable Displays
Range: up to 20 alphanumeric characters  DISP 1 ITEM 1: Range: 0 to 65535 in steps of 1   DISP 1 ITEM 5: Range: 0 to 65535 in steps of 1  5-118 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 293 If the parameters for the top line and the bottom line items have the same units, then the unit is displayed on the bottom line only. The units are only displayed on both lines if the units specified both the top and bottom line items are different. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-119...
Page 294: Direct Inputs And Outputs
DIRECT OUTPUT DEVICE ID messages. All UR-series IEDs in a ring need to have unique numbers assigned. The IED ID is used to identify the sender of the direct input and output message. 5-120 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 295 DIRECT I/O DATA RATE setting applies to a F60 with dual-channel communication cards and allows crossing DIRECT I/O CHANNEL CROSSOVER over messages from channel 1 to channel 2. This places all UR-series IEDs into one direct input and output network regardless of the physical media of the two communication channels.
Page 296 DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: DIRECT OUTPUT DEVICE ID: “2” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 3: 5-122 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 297 Figure 5-53: Three-terminal line application A permissive pilot-aided scheme can be implemented in a two-ring configuration, shown as follows (IEDs 1 and 2 constitute a first ring, while IEDs 2 and 3 constitute a second ring). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-123...
Page 298 In this application, apply the following settings. For UR-series IED 1: DIRECT OUTPUT DEVICE ID: “1” DIRECT I/O CH1 RING CONFIGURATION: “Yes” DIRECT I/O CH2 RING CONFIGURATION: “Yes” For UR-series IED 2: 5-124 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 299 EVENTS: Disabled The F60 checks integrity of the incoming direct input and output messages using a 32-bit CRC. The CRC alarm function is available for monitoring the communication medium noise by tracking the rate of messages failing the CRC check. The monitoring function counts all incoming messages, including messages that failed the CRC check.
Page 300: Teleprotection
 EVENTS: Disabled The F60 checks integrity of the direct input and output communication ring by counting unreturned messages. In the ring configuration, all messages originating at a given device should return within a pre-defined period of time. The unreturned messages alarm function is available for monitoring the integrity of the communication ring by tracking the rate of unreturned messages.
Page 301: Installation
5.4 Remote resources 5.4.1 Remote resources configuration When the F60 is ordered with a process card module as a part of HardFiber system, an additional Remote Resources menu tree is available in the EnerVista software to allow configuration of the HardFiber system.
Page 302 Bricks. Remote resources settings configure the point-to-point connection between specific fiber optic ports on the F60 process card and specific Brick. The relay is then configured to measure specific currents, voltages and contact inputs from those Bricks, and to control specific outputs.
Page 303: System Setup
The same rule applies for current sums from CTs with different secondary taps (5 A and 1 A). 5.5.1.2 Voltage banks SETTINGS  SYSTEM SETUP  AC INPUTS  VOLTAGE BANK F5(M5)  VOLTAGE BANK F5 PHASE VT F5 Range: Wye, Delta   CONNECTION: Wye F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-129...
Page 304: Power System
5-130 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 305: Signal Sources
“Disabled” only in unusual circumstances; consult GE Grid Solutions for special variable- FREQUENCY TRACKING frequency applications. The frequency tracking feature functions only when the F60 is in the “Programmed” mode. If the F60 is “Not Programmed,” then metering values are available but can exhibit significant errors. 5.5.3 Signal sources SETTINGS ...
Page 306 CHAPTER 5: SETTINGS When the F60 is equipped with a type 8Z CT/VT module for high impedance fault detection, do not assign the CT bank of this module to a source that is used by any conventional protection element. The type 8Z module CT bank is used solely by the high impedance fault detection algorithm.
Page 307 Figure 5-58: Example of use of sources Y LV D HV SRC 1 SRC 2 SRC 3 Phase CT F1+F5 None Ground CT None None Phase VT None None Aux VT None None F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-133...
Page 308: Breakers
1. The number of breaker control elements depends on the number of CT/VT modules specified with the F60. The following settings are available for each breaker control element.
Page 309 — This setting specifies the interval required to maintain setting changes in effect after an MANUAL CLOSE RECAL1 TIME operator has initiated a manual close command to operate a circuit breaker. — Selects an operand indicating that breaker 1 is out-of-service. BREAKER 1 OUT OF SV F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-135...
Page 310 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-59: Dual breaker control logic (Sheet 1 of 2) IEC 61850 functionality is permitted when the F60 is in “Programmed” mode and not in local control mode. 5-136 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 311 IEC 61850 trip and close commands shown is one protection pass only. To maintain the close/ open command for a certain time, do so on the contact outputs using the "Seal-in" setting, in the Trip Output element, or in FlexLogic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-137...
Page 312: Disconnect Switches
— This setting selects an operand that prevents opening of the disconnect switch. This setting can be SWITCH 1 BLK OPEN used for select-before-operate functionality or to block operation from a panel switch or from SCADA. 5-138 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 313 This allows for non-simultaneous operation of the poles. IEC 61850 functionality is permitted when the F60 is in “Programmed” mode and not in local control mode. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 314 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-61: Disconnect switch logic 5-140 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 315: Flexcurves
15.0 0.48 0.88 15.5 0.50 0.90 16.0 0.52 0.91 16.5 0.54 0.92 17.0 0.56 0.93 17.5 0.58 0.94 18.0 0.60 0.95 18.5 0.62 0.96 19.0 0.64 0.97 19.5 0.66 0.98 10.0 20.0 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-141...
Page 316 30 ms. At approximately four times pickup, the curve operating time is equal to the MRT and from then onwards the operating time remains at 200 ms. 5-142 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 317 Configuring a composite curve with an increase in operating time at increased pickup multiples is not allowed. If this is attempted, the EnerVista software generates an error message and discards the proposed changes. 5.5.6.5 Standard recloser curves The following graphs display standard recloser curves available for the F60. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-143...
Page 318 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-65: Recloser curves GE101 to GE106 Figure 5-66: Recloser curves GE113, GE120, GE138, and GE142 5-144 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 319 CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-67: Recloser curves GE134, GE137, GE140, GE151, and GE201 Figure 5-68: Recloser curves GE131, GE141, GE152, and GE200 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-145...
Page 320 SYSTEM SETUP CHAPTER 5: SETTINGS Figure 5-69: Recloser curves GE133, GE161, GE162, GE163, GE164, and GE165 Figure 5-70: Recloser curves GE116, GE117, GE118, GE132, GE136, and GE139 5-146 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 321 CHAPTER 5: SETTINGS SYSTEM SETUP Figure 5-71: Recloser curves GE107, GE111, GE112, GE114, GE115, GE121, and GE122 Figure 5-72: Recloser curves GE119, GE135, and GE202 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-147...
Page 322: Phasor Measurement Unit
  CONFIGURATION The F60 is provided with an optional Phasor Measurement Unit (PMU) feature. This feature is specified as a software option at the time of ordering. The number of PMUs available also depends on this option. Using the order code for your device, see the order codes in chapter 2 for details.
Page 323 NONE, which within the standard is classified as PRES OR UNKNOWN under the Calculation Method - ClcMth. Each Logical Device PMU supports one MxxMMXU, MxxMSQI, PxxxMMXU , PxxxMSQI, NxxMMXU, and one NxxMSQI logical node. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-149...
Page 324 All bitstrings less than or equal to 32 bits in length map into a 32 bit bitstring in an IEC 61850-90-5 dataset. The Value of the Nominal Frequency of the chassis is instantiated as a DO in LPHD of LD1. The value is named HzNom and is an Integer Status (INS). 5-150 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 325 5.5.7.5 Example: Creation of different data sets The aggregators allow the aggregation of phasors from multiple PMUs (with the same reporting rate) into a single custom data set to optimize bandwidth when streaming. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-151...
Page 326 5.5.7.6 Configuration example: CFG-2 based configuration (using IEC 61850-90-5) The F60 is expected to send the CFG-2 file (IEEE C37.118 config. file) upon request from the upstream synchrophasor devices (for example, P30) without stopping R-SV multicasting, as shown in the following figure. The primary domain controller (PDC) does not need to use a stop/start data stream command if the UR protocol is set to IEC 61850-90-5 prior to requesting the configuration via CFG-2 (IEEE C37.118 config.
Page 327 PMU 1 PHS-14: Range: available synchrophasor values  PMU 1 PHS- 1: Range: 16-character ASCII string  NM: GE-UR-PMU-PHS 1  PMU 1 PHS-14: Range: 16-character ASCII string  NM: GE-UR-PMU-PHS 14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-153...
Page 328 IEEE C37.118 protocol. This value is a 16-character ASCII string as per the IEEE C37.118 standard. — This setting specifies one of the available F60 signal sources for processing in the PMU. Any PMU 1 SIGNAL SOURCE combination of voltages and currents can be configured as a source.
Page 329 10 Hz, 12 Hz, 15 Hz, 20 Hz, 30 Hz, 60 Hz, or 120 Hz (or 10 Hz, 25 Hz, 50 Hz, or 100 Hz when the system frequency is 50 Hz) when entered via the keypad or software; and the F60 stops the transmission of reports.
Page 330 ANGLE: 0.00° PMU 1 VB CALIBRATION Range: 95.0 to 105.0 in steps of 0.1%  MAG: 100.0% PMU 1 VC CALIBRATION Range: –5.00 to 5.00° in steps of 0.05  ANGLE: 0.00° 5-156 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 331 When receiving synchrophasor data at multiple locations, with possibly different reference nodes, it can be more beneficial to allow the central locations to perform the compensation of sequence voltages. • This setting applies to PMU data only. The F60 calculates symmetrical voltages independently for protection and control purposes without applying this correction. •...
Page 332 This asserts individual trigger operand and overall TRIGGER DPO TIME PMU x TRIGGERED operand with stat bits 3 and 11 for a fixed interval defined by this setting. If it is required that operand with PMU x TRIGGERED 5-158 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 333 F60 standards. This element requires that the frequency be above the minimum measurable value. If the frequency is below this value, such as when the circuit is de-energized, the trigger drops out.
Page 334 — Use to extend the trigger after the situation returns to normal. This setting is of importance PMU 1 VOLT TRIGGER DPO TIME when using the recorder in the forced mode (recording as long as the triggering condition is asserted). 5-160 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 335 — Use to extend the trigger after the situation returns to normal. This setting is of PMU 1 CURR TRIGGER DPO TIME importance when using the recorder in the forced mode (recording as long as the triggering condition is asserted). Figure 5-82: Current trigger logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-161...
Page 336 — Use to extend the trigger after the situation returns to normal. This setting is of PMU 1 POWER TRIGGER DPO TIME particular importance when using the recorder in the forced mode (recording as long as the triggering condition is asserted). 5-162 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 337 — Use to extend the trigger after the situation returns to normal. This setting is of importance PMU 1 df/dt TRIGGER DPO TIME when using the recorder in the forced mode (recording as long as the triggering condition is asserted). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-163...
Page 338 Range: NONE, 37.118, 90-5   PROTOCOL: NONE PMU AGGREGATOR 1 Range: 1 to 65534 in steps of 1  IDCODE: 1 PMU AGGREGATOR 1 Range: No, Yes  INCLUDE PMU1: No 5-164 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 339 AGTR1 PDC CNTRL 3 Phasor data concentrator asserts control bit 3 as received via the network  as above AGTR1 PDC CNTRL 16 Phasor data concentrator asserts control bit 16, as received via the network F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-165...
Page 340 R-SV CB1 SVENA: Range: FlexLogic operand   CONFIGURATION R-SV CB1 CLIENT CTRL: Range: FlexLogic operand  R-SV CB1 SVENA DFLT: Range: FlexLogic operand  R-SV CB1 CONFREV: Range: 1 to 4294967295  5-166 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 341 — A range of values limited from 0 to 4095. R-SV CB1 VLAN ID — This setting allows the selection of a specific application ID for each sending device. R-SV CB1 APPID F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-167...
Page 342: Flexlogic
FlexLogic. In general, the system receives analog and digital inputs that it uses to produce analog and digital outputs. The figure shows major subsystems of a generic UR-series relay involved in this process. 5-168 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 343 Figure 5-86: UR architecture overview The states of all digital signals used in the F60 are represented by flags (or FlexLogic operands, which are described later in this section). A digital “1” is represented by a set flag. Any external contact change-of-state can be used to block an element from operating, as an input to a control feature in a FlexLogic equation, or to operate a contact output.
Page 344 The following table lists the operands available for the relay. The operands can be viewed online by entering the IP address of the relay in a web browser and accessing the Device Information Menu. 5-170 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 345 Breaker 1 flashover element phase B has dropped out BKR 1 FLSHOVR DPO C Breaker 1 flashover element phase C has dropped out BKR 1 FLSHOVR DPO Breaker 1 flashover element has dropped out F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-171...
Page 346 CT FAIL 1 PKP CT fail has picked up CT fail CT FAIL 1 OP CT fail has dropped out CT FAIL 2 to 4 Same set of operands as per CT FAIL 1 5-172 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 347 GROUND TOC1 OP Ground time overcurrent 1 has operated overcurrent GROUND TOC1 DPO Ground time overcurrent 1 has dropped out GROUND TOC2 to 4 Same set of operands as shown for GROUND TOC1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-173...
Page 348 NEUTRAL IOC1 OP Neutral instantaneous overcurrent 1 has operated instantaneous NEUTRAL IOC1 DPO Neutral instantaneous overcurrent 1 has dropped out overcurrent NEUTRAL IOC2 to 6 Same set of operands as shown for NEUTRAL IOC1 5-174 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 349 Phase B of overvoltage 1 has dropped out PHASE OV1 DPO C Phase C of overvoltage 1 has dropped out PHASE OV2 to 3 Same set of operands as shown for PHASE OV1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-175...
Page 350 Position of selector switch 1 is undetermined or restored from memory when the relay powers up and synchronizes to the three-bit input SELECTOR 2 Same set of operands as shown for SELECTOR 1 5-176 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 351 SYNC1 S-CLOSE OP DPO Synchrocheck 1 S-CLOSE has dropped out SYNC1 S-CLOSE ARMD Synchrocheck 1 S-CLOSE has been armed SYNC 2 to 4 Same set of operands as shown for SYNC 1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-177...
Page 352 Asserted while the RxGOOSE double-point status input is in the intermediate state RxG DPS 1 OFF Asserted while the RxGOOSE double-point status input is off RxG DPS 1 ON Asserted while the RxGOOSE double-point status input is on 5-178 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 353 Communications source of the reset command RESET OP (OPERAND) Operand (assigned in the INPUTS/OUTPUTS  RESETTING menu) source of the reset command RESET OP (PUSHBUTTON) Reset key (pushbutton) source of the reset command F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-179...
Page 354 2 to 16 any input is ‘1’ 2 to 16 all inputs are ‘1’ 2 to 16 all inputs are ‘0’ NAND 2 to 16 any input is ‘0’ only one input is ‘1’ 5-180 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 355: Flexlogic Rules
A timer operator (for example, "TIMER 1") or virtual output assignment (for example, " = Virt Op 1") can be used once only. If this rule is broken, a syntax error is declared. 5.6.3 FlexLogic evaluation Each equation is evaluated in the ascending order in which the parameters have been entered. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-181...
Page 356: Flexlogic Example
4, which is programmed in the contact output section to operate relay H1 (that is, contact output H1). Therefore, the required logic can be implemented with two FlexLogic equations with outputs of virtual output 3 and virtual output 4, shown as follows. 5-182 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 357 It is generally easier to start at the output end of the equation and work back towards the input, as shown in the following steps. It is also recommended F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-183...
Page 358 It is now possible to check that this selection of parameters produces the required logic by converting the set of parameters into a logic diagram. The result of this process is shown in the figure, which is compared to the logic for virtual output 3 diagram as a check. 5-184 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 359 Now check that the selection of parameters produce the required logic by converting the set of parameters into a logic diagram. The result is shown in the figure, which is compared to the logic for virtual output 4 diagram as a check. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-185...
Page 360 Always test the logic after it is loaded into the relay, in the same way as has been used in the past. Testing can be simplified by placing an "END" operator within the overall set of FlexLogic equations. The equations are evaluated up 5-186 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 361: Flexlogic Equation Editor
Range: Off, any analog actual value parameter  FLEXELEMENT 1 INPUT Range: SIGNED, ABSOLUTE  MODE: SIGNED FLEXELEMENT 1 COMP Range: LEVEL, DELTA  MODE: LEVEL FLEXELEMENT 1 Range: OVER, UNDER  DIRECTION: OVER F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-187...
Page 362 — This setting specifies the first (non-inverted) input to the FlexElement. Zero is assumed as the input if FLEXELEMENT 1 +IN this setting is set to “Off.” For proper operation of the element, at least one input must be selected. Otherwise, the element does not assert its output operands. 5-188 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 363 Figure 5-95: FlexElement direction, pickup, and hysteresis In conjunction with the setting, the element can be programmed to provide two extra FLEXELEMENT 1 INPUT MODE characteristics, as shown in the following figure. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-189...
Page 364 (Brk X Arc Amp A, B, and C) DCmA BASE = maximum value of the DCMA INPUT MAX setting for the two transducers configured under the +IN and –IN inputs DELTA TIME BASE = 1 µs 5-190 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 365: Non-Volatile Latches
Typical applications include sustaining operator commands or permanently blocking relay functions, such as Autorecloser, until a deliberate interface action resets the latch. — This setting characterizes Latch 1 to be Set- or Reset-dominant. LATCH 1 TYPE F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-191...
Page 366: Grouped Elements
SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  SETTING GROUP 1  LOAD ENCROACHMENT See below     PHASE CURRENT See page 5-195    NEUTRAL CURRENT See page 5-207   5-192 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 367: Load Encroachment
Range: Self-reset, Latched, Disabled  TARGET: Self-reset LOAD ENCROACHMENT Range: Disabled, Enabled  EVENTS: Disabled The load encroachment element responds to the positive-sequence voltage and current and applies a characteristic as shown in the figure. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-193...
Page 368 When the voltage is below this threshold, a blocking signal is not asserted by the element. When selecting this setting, remember that the F60 measures the phase-to-ground sequence voltages regardless of the VT connection. The nominal VT secondary voltage as specified with the SYSTEM SETUP ...
Page 369: Phase Current
 DIRECTIONAL 2 5.7.4.2 Inverse TOC curve characteristics The inverse time overcurrent curves used by the time overcurrent elements are the IEEE, IEC, GE Type IAC, and I t standard curve shapes. This allows for simplified coordination with downstream devices.
Page 370 IEEE Very Inverse 8.090 3.514 1.471 0.899 0.654 0.526 0.450 0.401 0.368 0.345 16.179 7.028 2.942 1.798 1.308 1.051 0.900 0.802 0.736 0.689 32.358 14.055 5.885 3.597 2.616 2.103 1.799 1.605 1.472 1.378 5-196 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 371 6.878 4.012 2.521 1.992 1.712 1.535 1.411 1.319 1.247 1.188 0.60 10.317 6.017 3.781 2.988 2.568 2.302 2.117 1.978 1.870 1.782 0.80 13.755 8.023 5.042 3.984 3.424 3.070 2.822 2.637 2.493 2.376 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-197...
Page 372 A to E = constants defined in the table = characteristic constant defined in the table = reset time in seconds (assuming energy capacity is 100% and RESET is “Timed”) RESET Table 5-33: GE type IAC inverse time curve constants IAC curve shape IAC Extreme Inverse 0.0040 0.6379...
Page 373 CHAPTER 5: SETTINGS GROUPED ELEMENTS IAC curve shape IAC Short Inverse 0.0428 0.0609 0.6200 –0.0010 0.0221 0.222 Table 5-34: GE type IAC curve trip times Multiplier Current ( I / I pickup (TDM) 10.0 IAC Extremely Inverse 1.699 0.749 0.303 0.178...
Page 374 T = Operate Time (in seconds) TDM = Multiplier setting I = Input Current = Pickup Current setting pickup = Reset Time in seconds (assuming energy capacity is 100% and RESET: Timed) RESET 5-200 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 375 CHAPTER 5: SETTINGS GROUPED ELEMENTS Recloser curves The F60 uses the FlexCurve feature to facilitate programming of 41 recloser curves. See the FlexCurves settings section earlier in this chapter for details. 5.7.4.3 Phase time overcurrent (ANSI 51P, IEC PTOC) SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  PHASE CURRENT  PHASE TOC1(4) ...
Page 376 — Selects the signal source for the phase time overcurrent protection element. SIGNAL SOURCE — Selects how phase current input quantities are interpreted by the F60. Inputs can be selected as fundamental INPUT phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 377 PHASE IOC1 BLOCK A: Range: FlexLogic operand   PHASE IOC1 BLOCK C: Range: FlexLogic operand  PHASE IOC1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset PHASE IOC1 Range: Disabled, Enabled  EVENTS: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-203...
Page 378 Range: 0.004 to 3.000 pu in steps of 0.001  THRESHOLD: 0.700 pu PHASE DIR 1 BLOCK Range: No, Yes  WHEN V MEM EXP: No PHASE DIR 1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset 5-204 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 379 (phase current) and the polarizing signal (the line voltage, shifted in the leading direction by the characteristic angle, ECA). The table shows the operating and polarizing signals used for phase directional control. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-205...
Page 380 When set to "No," the directional element allows tripping of phase overcurrent elements under directional control. — This setting enables and disables the logging of phase directional overcurrent events in the PHASE DIR 1 EVENTS sequence of events recorder. 5-206 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 381: Neutral Current
 NEUTRAL TOC 1 See below      NEUTRAL TOC 4    NEUTRAL IOC 1 See page 5-209     NEUTRAL IOC 6   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-207...
Page 382 — This setting selects the signal source for the neutral time overcurrent protection element. NEUTRAL TOC1 SIGNAL SOURCE — This setting selects how neutral current input quantities are interpreted by the F60. Inputs can be NEUTRAL TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 383 The positive-sequence restraint allows for more sensitive settings by counterbalancing spurious zero-sequence currents resulting from: • System unbalances under heavy load conditions • Transformation errors of current transformers (CTs) during double-line and three-phase faults • Switch-off transients during double-line and three-phase faults F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-209...
Page 384 VOLT: Calculated V0 NEUTRAL DIR OC1 OP Range: Calculated 3I0, Measured IG  CURR: Calculated 3I0 NEUTRAL DIR OC1 POS- Range: 0.000 to 0.500 in steps of 0.001  SEQ RESTRAINT: 0.063 5-210 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 385 The following tables define the neutral directional overcurrent element. V_0 is the zero-sequence voltage, I_0 is the zero-sequence current, ECA is the element characteristic angle, and IG is the ground current. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-211...
Page 386 This allows for better protection coordination. Take the bias into account when using the neutral directional overcurrent element to directionalize other protection elements. 5-212 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 387 A similar situation arises for a wye/delta/wye transformer, where current in one transformer winding neutral can reverse when faults on both sides of the transformer are considered. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-213...
Page 388 — This setting defines the pickup level for the overcurrent unit of the element in the reverse NEUTRAL DIR OC1 REV PICKUP direction. When selecting this setting, keep in mind that the design uses a positive-sequence restraint technique for the “Calculated 3I0” mode of operation. 5-214 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 389: Wattmetric Ground Fault
OV PKP: 0.20 pu WATTMETRIC GND FLT 1 Range: Calculated IN, Measured IG  CURR: Calculated IN WATTMETRIC GND FLT 1 Range: 0.002 to 30.000 pu in steps of 0.001  OC PKP: 0.060 pu F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-215...
Page 390 WATTMETRIC GND FLT 1 PWR PKP the 1 pu voltage as specified for the overvoltage condition of this element, and 1 pu current as specified for the overcurrent condition of this element. 5-216 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 391 The four FlexCurves allow for custom user-programmable time characteristics. When working with FlexCurves, the element uses the operate to pickup ratio, and the multiplier setting is not applied: Eq. 5-21 Again, the FlexCurve timer starts after the definite time timer expires. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-217...
Page 392 Figure 5-110: Wattmetric characteristic angle response — This setting is applicable if the is set to Inverse and WATTMETRIC GND FLT 1 MULTIPLIER WATTMETRIC GND FLT 1 CURVE defines the multiplier factor for the inverse time delay. 5-218 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 393: Ground Current
Figure 5-111: Wattmetric zero-sequence directional logic 5.7.7 Ground current 5.7.7.1 Menu SETTINGS  GROUPED ELEMENTS  SETTING GROUP 1(6)  GROUND CURRENT  GROUND CURRENT  GROUND TOC1 See below     F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-219...
Page 394 — This setting selects the signal source for the ground time overcurrent protection element. GROUND TOC1 SIGNAL SOURCE — This setting selects how ground current input quantities are interpreted by the F60. Inputs can be GROUND TOC1 INPUT selected as fundamental phasor magnitudes or total waveform RMS magnitudes as required by the application.
Page 395 GROUND IOC1 RESET Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 0.00 s GROUND IOC1 BLOCK: Range: FlexLogic operand  GROUND IOC1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-221...
Page 396 The resultant primary current is negligible for faults on the lower 30% of the winding 5-222 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 397 This is similar to a single infeed situation and can be mistaken for an internal fault. Similar difficulties occur in a breaker-and-a-half application of the restricted ground fault, where any through fault with a weak infeed from the winding itself can cause problems. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-223...
Page 398 (Igr(k)) does not reduce instantly but keeps decaying decreasing its value by 50% each 15.5 power system cycles. Having the differential and restraining signals developed, the element applies a single slope differential characteristic with a minimum pickup as shown in the following logic diagram. 5-224 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 399 Given the following inputs: IA = 1.10 pu ∠0°, IB = 1.0 pu ∠–120°, IC = 1.0 pu ∠120°, and IG = 0.05 pu ∠0° The relay calculates the following values: I_0 = 0.033 pu ∠0°, I_2 = 0.033 pu ∠0°, and I_1 = 1.033 pu ∠0° F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-225...
Page 400: Negative Sequence Current
 NEG SEQ DIR OC2   The F60 provides two negative-sequence time overcurrent elements, two negative-sequence instantaneous overcurrent elements, and two negative-sequence directional overcurrent elements. For information on the negative sequence time overcurrent curves, see the Inverse TOC Curve Characteristics section earlier.
Page 401 NEG SEQ IOC1 Range: 0.020 to 30.000 pu in steps of 0.001  PICKUP: 1.000 pu NEG SEQ IOC1 PICKUP Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 0.00 s F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-227...
Page 402 SOURCE: SRC 1 NEG SEQ DIR OC1 Range: 0.00 to 250.00 ohms in steps of 0.01  OFFSET: 0.00 Ω NEG SEQ DIR OC1 Range: Neg Sequence, Zero Sequence  TYPE: Neg Sequence 5-228 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 403 CT errors, since the current is low. The operating quantity depends on the way the test currents are injected into the F60. For single phase injection •...
Page 404 The reverse-looking function is faster compared to the forward-looking function, so use the reverse-looking function for the blocking direction. This allows for better protection coordination. Take this bias 5-230 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 405 NEG SEQ DIR OC1 REV PICKUP threshold applies to zero-sequence or negative-sequence current based on the setting. When NEG SEQ DIR OC1 TYPE selecting this setting, keep in mind that the design uses a positive-sequence restraint technique. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-231...
Page 406: Breaker Failure (Ansi 50Bf)
Range: 0.020 to 30.000 pu in steps of 0.001  PICKUP: 1.050 pu BF1 USE TIMER 1: Range: Yes, No  BF1 TIMER 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001  DELAY: 0.000 s 5-232 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 407 Because breaker failure can result in tripping a large number of breakers and this affects system safety and stability, a very high level of security is required. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-233...
Page 408 Output The outputs from the schemes are: • FlexLogic operands that report on the operation of portions of the scheme • FlexLogic operand used to re-trip the protected breaker 5-234 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 409 — If set to "Yes," the element is sealed-in if current flowing through the breaker is above the supervision BF1 USE SEAL-IN pickup level. — This setting selects the FlexLogic operand that initiates three-pole tripping of the breaker. BF1 3-POLE INITIATE F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-235...
Page 410 In microprocessor relays this time is not significant. In F60 relays, which use a Fourier transform, the calculated current magnitude ramps-down to zero one power frequency cycle after the current is interrupted, and this lag needs to be included in the overall margin duration, as it occurs after current interruption.
Page 411 Upon operation of the breaker failure element for a single pole trip command, a three-pole trip command needs to be given via output operand BKR FAIL 1 TRIP Figure 5-123: Single-pole breaker failure initiate logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-237...
Page 412 GROUPED ELEMENTS CHAPTER 5: SETTINGS Figure 5-124: Single-pole breaker failure, timers logic 5-238 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 413 CHAPTER 5: SETTINGS GROUPED ELEMENTS Figure 5-125: Three-pole breaker failure, initiate logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-239...
Page 414 GROUPED ELEMENTS CHAPTER 5: SETTINGS Figure 5-126: Three-pole breaker failure, timers logic 5-240 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 415: Voltage Elements
The time delay is adjustable from 0 to 600.00 seconds in steps of 0.01. The undervoltage elements can also be programmed to have an inverse time delay characteristic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-241...
Page 416 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s PHASE UV1 MINIMUM Range: 0.000 to 3.000 pu in steps of 0.001  VOLTAGE: 0.100 pu PHASE UV1 BLOCK: Range: FlexLogic operand  5-242 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 417 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s PHASE OV1 BLOCK: Range: FlexLogic Operand  PHASE OV1 Range: Self-reset, Latched, Disabled  TARGET: Self-reset PHASE OV1 Range: Disabled, Enabled  EVENTS: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-243...
Page 418 Range: 0.00 to 600.00 s in steps of 0.01  DELAY: 1.00 s NEUTRAL OV1 BLOCK: Range: FlexLogic operand  NEUTRAL OV1 TARGET: Range: Self-reset, Latched, Disabled  Self-reset NEUTRAL OV1 EVENTS: Range: Disabled, Enabled  Disabled 5-244 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 419 There are three negative-sequence overvoltage elements available. Use the negative-sequence overvoltage element to detect loss of one or two phases of the source, a reversed phase sequence of voltage, or a non-symmetrical system voltage condition. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-245...
Page 420 Range: Disabled, Enabled  Disabled The F60 contains one auxiliary undervoltage element for each VT bank. This element monitors undervoltage conditions of the auxiliary voltage. selects the voltage level at which the time undervoltage element starts timing. The nominal secondary...
Page 421 Range: Disabled, Enabled  Disabled The F60 contains one auxiliary overvoltage element for each VT bank. This element is intended for monitoring overvoltage conditions of the auxiliary voltage. The nominal secondary voltage of the auxiliary voltage channel entered under SYSTEM is the per-unit (pu) base used when setting the SETUP ...
Page 422: Sensitive Directional Power (Ansi 32)
The element has an adjustable characteristic angle and minimum operating power as shown in the Directional Power Characteristic diagram that follows. The element responds to the following condition: P cos θ + Q sin θ > SMIN Eq. 5-30 where 5-248 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 423 For example, section (a) in the figure shows settings for reverse power, while section (b) shows settings for low forward power applications. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-249...
Page 424 DIR POWER 1 RCA setting to “90°,” active underpower by setting to “180°,” and reactive underpower by DIR POWER 1 RCA DIR POWER 1 RCA setting to “270°.” DIR POWER 1 RCA 5-250 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 425: Control Elements
5.8.2 Trip bus SETTINGS  CONTROL ELEMENTS  TRIP BUS  TRIP BUS 1(6)  TRIP BUS 1 TRIP BUS 1 Range: Enabled, Disabled   FUNCTION: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-251...
Page 426 — The trip bus output is blocked when the operand assigned to this setting is asserted. TRIP BUS 1 BLOCK — This setting specifies a time delay to produce an output depending on how output is used. TRIP BUS 1 PICKUP DELAY 5-252 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 427: Setting Groups
Range: FlexLogic operand  GROUP 1 NAME: Range: up to 16 alphanumeric characters   GROUP 6 NAME: Range: up to 16 alphanumeric characters  SETTING GROUP Range: Disabled, Enabled  EVENTS: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-253...
Page 428: Selector Switch
Disabled. This resets the SelectActiveSG selection to 1. SETTING GROUPS FUNCTION 5.8.4 Selector switch SETTINGS  CONTROL ELEMENTS  SELECTOR SWITCH  SELECTOR SWITCH 1(2)  SELECTOR SWITCH 1 SELECTOR 1 FUNCTION: Range: Disabled, Enabled   Disabled 5-254 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 429 “Acknowledge,” the setting specifies the period of time for the acknowledging input to appear. The timer is re-started by any activity of the control input. The acknowledging input must come before the timer expires; SELECTOR 1 TIME-OUT otherwise, the change does not take place and an alarm is set. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-255...
Page 430 ( , accordingly). SELECTOR 1 ACK SELECTOR 1 3BIT ACK — This setting specifies the element behavior on power up of the relay. SELECTOR 1 POWER-UP MODE 5-256 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 431 The selector position pre-selected via the three-bit control input has not been confirmed before the time The following figures illustrate the operation of the selector switch. In these diagrams, “T” represents a time-out setting. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-257...
Page 432 CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-140: Time-out mode 5-258 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 433 1 through 3. The pre-selected setting group is to be applied automatically after five seconds of inactivity of the control inputs. When the relay powers up, it is to synchronize the setting group to the three-bit control input. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-259...
Page 434 SETTINGS  PRODUCT menu: SETUP  USER-PROGRAMMABLE PUSHBUTTONS  USER PUSHBUTTON 1 : “Self-reset” PUSHBUTTON 1 FUNCTION : “0.10 s” PUSHBUTTON 1 DROP-OUT TIME The figure shows the logic for the selector switch. 5-260 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 435: Underfrequency (Ansi 81U)
 DELAY : 2.000 s UNDERFREQ 1 TARGET: Range: Self-reset, Latched, Disabled  Self-reset UNDERFREQ 1 EVENTS: Range: Disabled, Enabled  Disabled There are six identical underfrequency elements, numbered 1 through 6. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-261...
Page 436: Overfrequency (Ansi 81O)
The channels are searched for the signal input in the following order: voltage channel A, auxiliary voltage channel, current channel A, and ground current channel. The first available signal is used for frequency calculation. 5-262 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 437: Frequency Rate Of Change (Ansi 81R)
Range: 0 to 65.535 s in steps of 0.001  DELAY: 0.000 s FREQ RATE 1 RESET Range: 0 to 65.535 s in steps of 0.001  DELAY: 0.000 s FREQ RATE 1 BLOCK: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-263...
Page 438 If the signal source assigned to the frequency rate of change element is only set to auxiliary VT, then the minimum voltage supervision is 3 V. Figure 5-145: Frequency rate of change logic 5-264 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 439: Synchrocheck (Ansi 25)
The synchronism check function supervises the paralleling of two parts of a system that are to be joined by the closure of a circuit breaker. The synchrocheck elements are typically used at locations where the two parts of the system are interconnected through at least one other point in the system. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-265...
Page 440 Figure 5-146: Synchrocheck plot for slip > 0 (slip = F2-F1) 5-266 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 441 The selected sources for synchrocheck inputs V1 and V2 (which must not be the same source) can include both a three-phase and an auxiliary voltage. The relay automatically selects the specific voltages to be used by the synchrocheck element in accordance with the following table. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-267...
Page 442 The relay uses the phase channel of a three-phase set of voltages if programmed as part of that source. The relay uses the auxiliary voltage channel only if that channel is programmed as part of the Source and a three-phase set is not. 5-268 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 443 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-148: Synchrocheck logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-269...
Page 444: Autoreclose (Ansi 79)
Range: FlexLogic operand  AR1 DELAY 2: Range: 0.00 to 655.35 s in steps of 0.01  0.000 s AR1 RESET LOCKOUT Range: 0.00 to 655.35 s in steps of 0.01  DELAY: 60.000 5-270 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 445  Disabled The F60 is provided with this optional feature, specified as an option at the time of ordering. Using the order code for your device, see the order codes in chapter 2 for details. The maximum number of autoreclosure elements available is equal to the number of installed CT banks.
Page 446 "reclose-in-progress" state. If all conditions allowing a breaker closure are not satisfied when this time expires, the scheme goes to Lockout. This timer must be set to a delay less than the reset timer. 5-272 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 447 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-149: Autoreclosure logic (Sheet 1 of 2) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-273...
Page 448 CONTROL ELEMENTS CHAPTER 5: SETTINGS Figure 5-150: Autorecloser logic (Sheet 2 of 2) 5-274 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 449 CHAPTER 5: SETTINGS CONTROL ELEMENTS Figure 5-151: Single shot autoreclosing sequence - permanent fault F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-275...
Page 450: Digital Elements
DIGITAL ELEMENT 1 RESET DELAY — This setting enables or disabled the digital element pickup LED. When set to “Disabled,” the DIGITAL ELEMENT 1 PICKUP LED operation of the pickup LED is blocked. 5-276 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 451 In most breaker control circuits, the trip coil is connected in series with a breaker auxiliary contact that is open when the breaker is open (see figure). To prevent unwanted alarms in this situation, the trip circuit monitoring logic must include the breaker position. Figure 5-153: Trip circuit example 1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-277...
Page 452 In this case, it is not required to supervise the monitoring circuit with the breaker position – the setting is BLOCK selected to “Off.” In this case, the settings are as follows (EnerVista example shown). 5-278 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 453: Digital Counters
COUNTER 1 BLOCK: Range: FlexLogic operand  CNT1 SET TO PRESET: Range: FlexLogic operand  COUNTER 1 RESET: Range: FlexLogic operand  COUNT1 FREEZE/RESET: Range: FlexLogic operand  COUNT1 FREEZE/COUNT: Range: FlexLogic operand  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-279...
Page 454 If control power is interrupted, the accumulated and frozen values are saved into non-volatile memory during the power-down operation. 5-280 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 455: Monitoring Elements
 BREAKER   FLASHOVER 2  BREAKER RESTRIKE 1 See page 5-296     BREAKER RESTRIKE 4    CT FAILURE See page 5-298   DETECTOR 1  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-281...
Page 456 THRESHOLD: 15% HI-Z 3-PHASE EVENT Range: 1 to 1000 A in steps of 1  THRESHOLD: 25 A HI-Z VOLTAGE SUPV Range: 0 (off) to 100% in steps of 1  THRESHOLD: 5% 5-282 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 457 Flag indicating an instantaneous 2-cycle overcurrent was detected LossOfLoad Flag indicating a loss of load was detected EadZeroed Flag indicating that this phase’s EAD table was cleared HighZArmed Flag indicating that this phase is armed for a high-Z detection F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-283...
Page 458 “Normal”. Also, if two minutes pass without high levels from the Expert Arc Detector Algorithm while the algorithm is in its Armed state, then it moves from the “Armed” state directly back to the “Normal” state. 5-284 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 459 It is recommended that this setting is above the maximum 3Io (residual) current due to unbalanced loading. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-285...
Page 460 For the first three to five days after installation (or after being out-of-service for a significant period), the F60 can identify some of this noise as arcing. Take this into account when responding to alarms during these operating periods.
Page 461 5.9.0.3 Breaker arcing current SETTINGS  CONTROL ELEMENTS  MONITORING ELEMENTS  BREAKER 1(4) ARCING CURRENT  BREAKER 1 BKR 1 ARC AMP Range: Disabled, Enabled   ARCING CURRENT FUNCTION: Disabled F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-287...
Page 462 (breaker operating time), clear ARCING AMPS (kA -cycle) and AMP MAX (kA) values of the last event. — This setting specifies the maximum symmetrical interruption rating of the circuit breaker. BKR 1 INTERUPTION RATING 5-288 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 463 CHAPTER 5: SETTINGS MONITORING ELEMENTS Figure 5-157: Arcing current measurement F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-289...
Page 464 MONITORING ELEMENTS CHAPTER 5: SETTINGS Figure 5-158: Breaker arcing current logic 5-290 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 465 (contact input indicating the breaker status is off), and no flashover current is flowing. A contact showing the breaker status must be provided to the relay. The voltage difference is not considered as a condition for open breaker in this part of the logic. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-291...
Page 466 This application does not require detection of breaker status via a 52a contact, as it uses a voltage difference larger than setting. However, monitoring the breaker contact ensures scheme stability. BRK 1 FLSHOVR DIFF V PKP 5-292 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 467 (all line breakers open), to well above the maximum line (feeder) load (line/feeder connected to load). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-293...
Page 468 A six-cycle time delay applies after the selected FlexLogic operand resets. — This setting specifies the time delay to operate after a pickup condition is detected. BRK FLSHOVR PKP DELAY 5-294 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 469 CHAPTER 5: SETTINGS MONITORING ELEMENTS Figure 5-159: Breaker flashover logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-295...
Page 470 The user can add counters and other logic to facilitate the decision making process as to the appropriate actions upon detecting a single restrike or a series of consecutive restrikes. 5-296 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 471 1/8th of the power cycle. — Enables/disables high-frequency (HF) pattern detection when breaker restrike occurs. BREAKER RESTRIKE 1 HF DETECT High-frequency pattern is typical for capacitor bank, cables, and long transmission lines applications. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-297...
Page 472 Range: 0.04 to 2.00 pu in steps of 0.01  PKP: 0.20 pu CT FAIL 1 PICKUP Range: 0.000 to 65.535 s in steps of 0.001  DELAY: 1.000 s CT FAIL 1 TARGET: Range: Self-reset, Latched, Disabled  Self-reset 5-298 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 473 — Specifies the pickup value for the 3V_0 source. CT FAIL 1 3V0 INPUT PICKUP — Specifies the pickup delay of the CT failure element. CT FAIL 1 PICKUP DELAY Figure 5-163: CT failure detector logic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-299...
Page 474 B current (red). The superimposed current shows two fault current blips as the data slides through the two-cycle memory window. During the actual fault, the neutral current and the superimposed phase B currents closely correspond, confirming the incipient fault hypothesis and identifying the affected phase. 5-300 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 475 — Specifies a time window for “Counts per window” mode of operation. INCIPNT FLT 1 DETECT WINDOW — Specifies a reset time for the output after the trip is initiated. INCIPIENT FAULT 1 RESET DELAY F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-301...
Page 476 An additional condition is introduced to inhibit a fuse failure declaration when the monitored circuit is de-energized; positive-sequence voltage and current are both below threshold levels. — Enables and disables the fuse failure feature for Source 1 VT Fuse Fail. VT FUSE FAILURE 1 FUNCTION 5-302 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 477 THERMAL PROTECTION 1 Range: 0.20 to 3.00 pu in steps of 0.01  BASE CURR: 0.80 pu THERMAL PROTECTION 1 Range: 1.00 to 1.20 in steps of 0.05  k FACTOR: 1.10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-303...
Page 478 The reset time of the thermal overload protection element is also time delayed using following formula: Eq. 5-34 where τ = thermal protection trip time constant = a minimum reset time setting 5-304 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 479 IEC255-8 cold curve or hot curve equations op(In) is the reset time calculated at index n as per the reset time equation rst(In) F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-305...
Page 480 BROKEN CONDUCTOR 1 Range: 20.0% to 100.0% in steps of 0.1%  I2/I1 RATIO: 20% BROKEN CONDUCTOR 1 Range: 0.05 to 1.00 pu in steps of 0.01  I1 MIN: 0.10 pu 5-306 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 481 — This setting specifies the pickup time delay for this function to operate after assertion BROKEN CONDUCTOR 1 PKP DELAY of the broken conductor pickup FlexLogic operand. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-307...
Page 482 MONITORING ELEMENTS CHAPTER 5: SETTINGS Figure 5-169: Broken conductor detection logic 5-308 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 483: Cold Load Pickup
The reset delay interval is intended to be set to a ON-LOAD TIME BEFORE RESET period until the feeder load has decayed to normal levels, after which other features can be used to switch setting groups. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-309...
Page 484: Pilot Schemes
 DELAY: 0.090 s ECHO DURATION: Range: 0.000 to 65.535 s in steps of 0.001  0.100 s ECHO LOCKOUT: Range: 0.000 to 65.535 s in steps of 0.001  0.250 s 5-310 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 485 — This setting allows the user to select the FlexLogic operand to represent the Line End Open POTT3 LINE END OPEN condition, such as breaker open status, or under voltage and under current conditions. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-311...
Page 486 Figure 5-172: POTT3 scheme logic 5.9.2.2 Directional comparison blocking 3 (DCB3) SETTINGS  CONTROL ELEMENTS  PILOT SCHEMES  DCB3 SCHEME  BLOCKING3 SCHEME DCB3 SCHEME Range: Disabled, Enabled  FUNCTION: Disabled  5-312 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 487 If the reverse fault condition prevails for , the blocking operation is extended by the TRANS BLOCK PICKUP DELAY transient blocking timer for . This allows riding through current reversal conditions. However, if TRANS BLOCK RESET DELAY F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-313...
Page 488 FORCE TX STOP. — This setting selects the FlexLogic operands to represent the receive signals for the scheme. Contact inputs DCB3 RX interfacing with a signaling system(s) are used typically. 5-314 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 489: Inputs/Outputs
Range: 0.0 to 16.0 ms in steps of 0.5  DEBNCE TIME: 6.0 ms CONTACT INPUT H5a Range: Disabled, Enabled  EVENTS: Disabled ↓  CONTACT INPUT xxx    CONTACT INPUT   THRESHOLDS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-315...
Page 490 The DC input voltage is compared to a user-settable threshold. A new contact input state must be maintained for a user-settable debounce time in order for the F60 to validate the new contact state. In the following figure, the debounce time is set at 2.5 ms;...
Page 491: Virtual Inputs
The virtual inputs and outputs are digital signals associated with UR-series internal logic signals. Virtual inputs include signals generated by the local user interface. The virtual outputs are outputs of FlexLogic equations used to customize the device. Virtual outputs can also serve as virtual inputs to FlexLogic equations. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-317...
Page 492: Contact Outputs
(virtual output, element state, contact input, or virtual input). An additional FlexLogic operand can be used to SEAL-IN the relay. Any change of state of a contact output can be logged as an Event if programmed to do so. 5-318 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 493 If any latching outputs exhibits a discrepancy, the LATCHING OUTPUT ERROR self-test error is declared. The error is signaled by the FlexLogic operand, event, and target message. LATCHING OUT ERROR F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-319...
Page 494 (assuming an H4L module): OUTPUTS  CONTACT OUTPUT H1a CONTACT OUTPUT H1c : “VO1” OUTPUT H1a OPERATE : “VO2” OUTPUT H1a RESET : “VO2” OUTPUT H1c OPERATE : “VO1” OUTPUT H1c RESET 5-320 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 495 Program the Latching Outputs by making the following changes in the SETTINGS  INPUTS/OUTPUTS  CONTACT menu (assuming an H4L module): OUTPUTS  CONTACT OUTPUT H1a : “VO1” OUTPUT H1a OPERATE : “VO2” OUTPUT H1a RESET F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-321...
Page 496: Virtual Outputs
BIT NUMBER: DIRECT INPUT 1 Range: On, Off, Latest/On, Latest/Off  DEFAULT: Off DIRECT INPUT 1 Range: Enabled, Disabled  EVENTS: Disabled These settings specify how the direct input information is processed. 5-322 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 497 Assume that contact input 1 from UR IED 2 is to be used by UR IED 1. The following settings are applied (Direct Input 5 and bit number 12 are used, as an example). F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-323...
Page 498 (if any default state is set to “On”), or to trip the bus on any overcurrent condition (all default states set to “Off”). 5-324 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 499 DIRECT OUT 2 OPERAND TX1" "DIRECT INPUT 5" (forward a message from 1 to 3) DIRECT OUT 3 OPERAND "DIRECT INPUT 6" (forward a message from 3 to 1) DIRECT OUT 4 OPERAND F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-325...
Page 500: Teleprotection
The “Latest/On” and “Latest/Off” values freeze the input in case of lost communications. If the latest state is not known, such as after relay power-up but before the first communication exchange, then the input defaults to logic 1 for “Latest/ On” and logic 0 for “Latest/Off.” 5-326 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 501 (teleprotection outputs at the sending end or corresponding teleprotection inputs at the receiving end). On three-terminal two-channel systems, redundancy is achieved by programming signal re-transmittal in the case of channel failure between any pair of relays. Figure 5-183: Teleprotection input/output processing F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-327...
Page 502: Transducer Inputs/Outputs
VALUE: 0.000 The F60 is provided with optional DCmA capability. This feature is specified as an option at the time of ordering. See the Order Codes section in chapter 2 for details. Hardware and software are provided to receive signals from external transducers and to convert these signals into a digital format for use as required.
Page 503: Rtd Inputs
1.5 pu. FlexElement operands are available to FlexLogic for further interlocking or to operate an output contact directly. See the following table for reference temperature values for each RTD type. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-329...
Page 504: Dcma Outputs
DCMA OUTPUT H1 Range: –90.000 to 90.000 pu in steps of 0.001  MIN VAL: 0.000 pu DCMA OUTPUT H1 Range: –90.000 to 90.000 pu in steps of 0.001  MAX VAL: 1.000 pu 5-330 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 505 — This setting allows selection of the output range. Each DCmA channel can be set independently DCMA OUTPUT H1 RANGE to work with different ranges. The three most commonly used output ranges are available. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-331...
Page 506 The CT ratio is 5000:5 and the maximum load current is 4200 A. The current is to be monitored from 0 A upwards, allowing for 50% overload. The phase current with the 50% overload margin is: Eq. 5-43 5-332 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 507 ±0.5% of the full scale for the analog output module, or ± 0.005 x (1-0) x 254.03 kV = ±1.27 kV • ±0.5% of reading For example, under nominal conditions, the positive-sequence reads 230.94 kV and the worst-case error is 0.005 × 230.94 kV + 1.27 kV = 2.42 kV. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-333...
Page 508: Testing
 FUNCTION: Disabled The F60 provides a test facility to verify the functionality of contact inputs and outputs, some communication functions and the phasor measurement unit (where applicable), using simulated conditions. The test mode can be in any of three states: Disabled, Isolated, or Forcible.
Page 509: Phasor Measurement Unit Test Values
PMU 1 IC TEST Range: –180.00 to 180.00° in steps of 0.05  ANGLE: 110.00° PMU 1 IG TEST Range: 0.000 to 9.999 kA in steps of 0.001  MAGNITUDE: 0.000 kA F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-335...
Page 510: Force Contact Inputs
TEST MODE FORCING their default states. 5.12.5 Force contact outputs SETTINGS  TESTING  FORCE CONTACT OUTPUTS  FORCE CONTACT FORCE Cont Op 1 Range: Normal, Energized, De-energized, Freeze   OUTPUTS : Normal 5-336 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 511 While the selected operand is Off, the output behaves as it does when in service. On restart, the setting and the force contact input and force contact output settings revert to TEST MODE FORCING their default states. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 5-337...
Page 512 TESTING CHAPTER 5: SETTINGS 5-338 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 513: Actual Values
   AUTORECLOSE See page 6-7    RxGOOSE STATUS See page 6-6    RxGOOSE See page 6-6   STATISTICS  DIGITAL COUNTERS See page 6-7   F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 514  OF CHANGE  FLEXELEMENTS See page 6-24    RxGOOSE Analogs See page 6-25    WATTMETRIC See page 6-25   GROUND FAULT 1  WATTMETRIC   GROUND FAULT 2 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 515: Front Panel
The front panel can be viewed and used in the EnerVista software, for example to view an error message displayed on the front panel. To view the front panel in EnerVista software: Click Actual Values > Front Panel. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 516: Status
The present status of the 64 virtual inputs is shown here. The first line of a message display indicates the ID of the virtual input. For example, ‘Virt Ip 1’ refers to the virtual input in terms of the default name. The second line of the display indicates the logic state of the virtual input. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 517: Rxgoose Boolean Inputs
Range: On, Off  STATUS: Off The F60 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. 6.3.4 RxGOOSE DPS inputs ACTUAL VALUES ...
Page 518: Virtual Outputs
 Offline The F60 is provided with optional IEC 61850 capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. actual value does not consider RxGOOSE that are not configured or are not used by any RxGOOSE All RxGOOSE Online Input.
Page 519: Autoreclose
PARAM 1: Off Range: On, Off    PARAM 256: Off Range: On, Off  There are 256 FlexState bits available. The second line value indicates the state of the given FlexState bit. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 520: Ethernet
PTP - IRIG-B DELTA being received via PTP and that being received via IRIG-B. A positive value indicates that PTP time is fast compared to IRIG- B time. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 521: Hi-Z Status
6.3.18 Direct devices status ACTUAL VALUES  STATUS  DIRECT DEVICES STATUS  DIRECT DEVICES DIRECT DEVICE 1 Range: Offline, Online   STATUS STATUS: Offline  DIRECT DEVICE 16 Range: Offline, Online  STATUS: Offline F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 522: Egd Protocol Status
If a remote relay ID does not match the programmed ID at the local relay, the “FAIL” message displays. The “N/A” value appears if the local relay ID is set to a default value of “0,” the channel is failed, or if the teleprotection inputs/outputs are not enabled. 6-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 523: Incipient Fault Detector
ACTUAL VALUES  STATUS  PRP STATUS  PRP STATUS Total Rx Port A: Range: 0 to 4G, blank if PRP disabled   Total Rx Port B: Range: 0 to 4G, blank if PRP disabled  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-11...
Page 524: Txgoose Status
Range: 0 to 4G, blank if PRP disabled  The F60 is provided with optional PRP capability. This feature is specified as a software option at the time of ordering. See the Order Codes section in chapter 2 for details.
Page 525: Metering
CHAPTER 6: ACTUAL VALUES METERING 6.4 Metering 6.4.1 Metering conventions 6.4.1.1 UR convention for measuring power and energy The figure illustrates the conventions established for use in UR devices. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-13...
Page 526 6.4.1.2 UR convention for measuring phase angles All phasors calculated by URs and used for protection, control and metering functions are rotating phasors that maintain the correct phase angle relationships with each other at all times. 6-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 527 For display and oscillography purposes the phase angles of symmetrical components are referenced to a common reference as described in the previous sub-section. WYE-connected instrument transformers • ABC phase rotation: • ACB phase rotation: The above equations apply to currents as well. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-15...
Page 528 * The power system voltages are phase-referenced – for simplicity – to V and V , respectively. This, however, is a relative matter. It is important to remember that the F60 displays are always referenced as specified under SETTINGS  SYSTEM SETUP  POWER SYSTEM  FREQUENCY AND PHASE REFERENCE The example above is illustrated in the following figure.
Page 529: Sources
0.000 A SRC 1 RMS In:  0.000 A SRC 1 PHASOR Ia:  0.000 A 0.0° SRC 1 PHASOR Ib:  0.000 A 0.0° SRC 1 PHASOR Ic:  0.000 A 0.0° F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-17...
Page 530 0.00 V SRC 1 RMS Vbc:  0.00 V SRC 1 RMS Vca:  0.00 V SRC 1 PHASOR Vab:  0.000 V 0.0° SRC 1 PHASOR Vbc:  0.000 V 0.0° 6-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 531 SRC 1 APPARENT PWR  3φ: 0.000 VA SRC 1 APPARENT PWR  φa: 0.000 VA SRC 1 APPARENT PWR  φb: 0.000 VA SRC 1 APPARENT PWR  φc: 0.000 VA F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-19...
Page 532 S = V x Î x Î x Î Eq. 6-1 When VTs are configured in delta, the F60 does not calculate power in each phase and three-phase power is measured as S = V x Î x Î Eq. 6-2...
Page 533 The signal used for frequency estimation is low-pass filtered. The final SYSTEM SETUP  POWER SYSTEM frequency measurement is passed through a validation filter that eliminates false readings due to signal distortions and transients. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-21...
Page 534 The harmonics are a percentage of the fundamental signal obtained as a ratio of harmonic amplitude to fundamental amplitude multiplied by 100%. The total harmonic distortion (THD) is the ratio of the total harmonic content to the fundamental: Eq. 6-4 6-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 535: Sensitive Directional Power
V2 ANG: 0.0° SYNCHROCHECK 1 PROJ  DELTA_PHASE: 0.0° SYNCHROCHECK 1 PROJ  SYNSCP D_PH: 0.0° If synchrocheck or a setting is "Disabled," the corresponding actual values menu item does not display. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-23...
Page 536: Tracking Frequency
= maximum nominal primary RMS value of the +IN and –IN inputs BASE SYNCHROCHECK = maximum primary RMS value of all the sources related to the +IN and –IN inputs BASE (Max Delta Volts) 6-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 537: Rxgoose Analogs
 0.000 The F60 is provided with optional GOOSE communications capability. This feature is specified as a software option at the time of ordering. See the Order Codes section of chapter 2 for details. The RxGOOSE Analog values display in this menu. The RxGOOSE Analog values are received via IEC 61850 GOOSE messages sent from other devices.
Page 538: Pmu Aggregator
 -50 °C  Actual values for each RTD input channel that is enabled are displayed with the top line as the programmed channel ID and the bottom line as the value. 6-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 539: Records
IG is the ground current from the parallel line scaled to the source phase CT in secondary amps. Z0/Z1 is the zero sequence impedance to positive sequence impedance ratio, and Z0M/Z1 is mutual zero sequence impedance to positive sequence impedance ratio. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-27...
Page 540: Event Records
The event records are also viewable in the software and in a web browser. The figure shows the event records in the software. To view them in a web browser, enter the IP address of the device. Figure 6-5: Event records viewed in EnerVista software 6-28 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 541: Oscillography
ACTUAL VALUES  RECORDS  PMU RECORDS  PMU 1 RECORDING  PMU 1 PMU 1 FORCE TRIGGER: Range: No, Yes   RECORDING PUM 1 AVAILABLE Range: 0 to 65535 in steps of 1  RECORDS: 0 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-29...
Page 542: Breaker Maintenance
All of the values are stored in non-volatile memory and retained with power cycling. 6.5.7 Hi-Z records ACTUAL VALUES  RECORDS  HIZ RECORDS  HIZ RECORDS FORCE TRIGGER:   HIZ 1:NONE  1970/01/01 00:00:00 6-30 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 543: Product Information
Range: operating time in HH:MM:SS  0:00:00 PMU FEATURE ACTIVE: Range: Yes, No  CT/ VT ADVANCED DIAG Range: Yes, No  ACTIVE: No LAST SETTING CHANGE: Range: YYYY/MM/DD HH:MM:SS  1970/01/01 23:11:19 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 6-31...
Page 544: Firmware Revisions
Range: YYYY/MM/DD HH:MM:SS  2016/09/15 16:41:32 Date and time when the FPGA was built. The shown data is illustrative only. A modification file number of 0 indicates that, currently, no modifications have been installed. 6-32 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 545: Commands And Targets
The commands menu contains relay directives intended for operations personnel. All commands can be protected from unauthorized access via the command password; see the Security section of chapter 5 for details. The following flash message appears after successfully command entry. COMMAND EXECUTED F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 546: Virtual Inputs
Range: No, Yes  CHANGE COUNTER? No CLEAR TELEPROTECT Range: No, Yes  COUNTERS? No CLEAR INCIPIENT Range: No, Yes  FAULT COUNTERS? No  CLEAR IEC61850 See below   XWSI OPCNT F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 547: Set Date And Time
COMMANDS  RELAY MAINTENANCE  COMMANDS PERFORM LAMP TEST? Range: No, Yes   RELAY MAINTENANCE UPDATE ORDER CODE? Range: No, Yes  REBOOT RELAY? Range: No, Yes  SERVICE COMMAND Range: 0, 101  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 548: Phasor Measurement Unit One-Shot
Although the diagnostic information is cleared before the F60 is shipped from the factory, the user can want to clear the diagnostic information for themselves under certain circumstances. For example, you clear diagnostic information after replacement of hardware. Once the diagnostic information is cleared, all self-checking variables are reset to their initial state and diagnostics restart from scratch.
Page 549 30 seconds afterwards PMU ONE-SHOT OP When the function is disabled, all three operands are de-asserted. The one-shot function applies to all logical PMUs of a given F60 relay. Figure 7-1: PMU one-shot FlexLogic operands 7.1.5.1 Testing accuracy of the PMU The one-shot feature is used to test accuracy of the synchrophasor measurement.
Page 550: Security
— Selecting ‘Yes’ allows the Supervisor to forcefully logoff an operator session. OPERATOR LOGOFF — Selecting ‘Yes’ allows the Supervisor to forcefully clear all the security logs and clears all the CLEAR SECURITY DATA operands associated with the self-tests. 7.2 Targets menu TARGETS  F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 551: Target Messages
A target enables the EnerVista UR Setup software to monitor automatically and display the status of any active target messages of all the devices inserted into that site. Each F60 element with a TARGET setting has a target message that when activated by its element is displayed in sequence with any other currently active target messages in the menu.
Page 552 Contact Factory (xxx) • Latched target message: Yes. • Description of problem: One or more installed hardware modules is not compatible with the F60 order code. • How often the test is performed: Module dependent. • What to do: Contact the factory and supply the failure code noted in the display. The “xxx” text identifies the failed module (for example, F8L).
Page 553 Description of problem: A bad IRIG-B input signal has been detected. • How often the test is performed: Monitored whenever an IRIG-B signal is received. • What to do: Ensure the following: – The IRIG-B cable is properly connected. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 554 How often the test is performed: On any setting changes, when new settings were written to device. • What to do: Verify that the setting change was legitimate and essential for proper functioning of the protection and control system. 7-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 555 Description of problem: The ambient temperature is greater than the maximum operating temperature (+80°C). • How often the test is performed: Every hour. • What to do: Remove the F60 from service and install in a location that meets operating temperature standards. UNEXPECTED RESTART: Press “RESET” key •...
Page 556 Description of problem: A setting write was attempted while the lock relay setting was enabled. • What to do: Ask the Supervisor to unlock the settings and try again. SERVER UNAVAILABLE • Message: "An attempt to contact the Radius server has failed" 7-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 557 Brick. Where multiple UR-series devices have self-test errors, look for common causes. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 7-13...
Page 558 Brick output failing to respond to an output command can only be detected while the command is active, and so in this case the target is latched. A latched target can be unlatched by pressing the faceplate reset key if the command has ended, however the output can still be non-functional. 7-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 559: Commissioning
Injection to a particular F60 frequency element must be to its configured source and to the channels that the source uses for frequency measurement. For frequency measurement, a source uses the first quantity configured in the following...
Page 560 0.20 Hz before the threshold and subtract 1 second from the test set time reading of ramp start to relay operation. Note that the F60 event records only show the “pickup delay” component, a definite time timer. This is exclusive of the time taken by the frequency responding component to pickup.
Page 561: Theory Of Operation
LEDs are activated on the relay faceplate. The detection of a downed conductor or arcing condition is accomplished through the following algorithms: • Energy algorithm • Randomness algorithm • Expert Arc Detector algorithm F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 562: Energy Algorithm
These increases in confidence levels occur because multiple, consecutive indications from a given algorithm and indications from multiple independent algorithms are more indicative of the presence of arcing than a single algorithm giving a single indication. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 563: Spectral Analysis Algorithm
This information is then provided as input to the Arc Burst Pattern Analysis algorithm. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 564: Arc Burst Pattern Analysis Algorithm
The single-ended fault location method assumes that the fault components of the currents supplied from the local (A) and remote (B) systems are in phase. The figure shows an equivalent system for fault location. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 565 Depending on the fault type, appropriate voltage and current signals are selected from the phase quantities before applying the preceding equation (the superscripts denote phases, the subscripts denote stations). For AG faults: Eq. 9-5 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 566 If the VTs are connected in a delta configuration, fault location is performed based on the delta voltages and zero-sequence voltage approximated based on the zero-sequence current: Eq. 9-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 567 CHAPTER 9: THEORY OF OPERATION FAULT LOCATOR where Z is the equivalent zero-sequence impedance behind the relay as entered under the fault report setting menu. SYS0 Figure 9-2: Fault locator scheme F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 568 FAULT LOCATOR CHAPTER 9: THEORY OF OPERATION F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 569: Maintenance
UR Family Communications Guide for the entries. The upper part of the window displays values. The lower part of the window is for factory service use. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-1...
Page 570 Float — A numbering system with no fixed number of digits before or after the decimal point. An example is 0.000000. Binary — A numbering system using 0 and 1. An example is 0000-0000-0000-0000. Entries are not saved when closing the window. 10-2 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 571: General Maintenance
GENERAL MAINTENANCE 10.2 General maintenance The F60 requires minimal maintenance. As a microprocessor-based relay, its characteristics do not change over time. Expected service life is 20 years for UR devices manufactured June 2014 or later when applied in a controlled indoors environment and electrical conditions within specification.
Page 572: Cybersentry Security Event Files
15 = Role Log in 10.3.1.2 Setting changes file The SETTING_CHANGES.LOG file stores all the setting changes. A total of 1024 events are stored in a circular buffer in non- volatile memory. 10-4 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 573: Compare Settings
Comparison Report: Sequential File 1, File 2 Layout — When disabled (default), the report shows only what differs, as shown in the previous figure. When enabled, the report indicates differences by device. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-5...
Page 574: Back Up And Restore Settings
LED operands are not modeled. If the block setting of the Phase IOC is configured with LED operands, its displays as TBD in IID and CID files, the web interface, or in an MMS client. 10-6 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 575 Hqve this option enabled when you want to keep the IID file from the UR device instead of from another tool. The location of the file is C:\ProgramData\GE Power Management\urpc\Offline, for example.
Page 576: Restore Settings
IID type backup was created either using the EnerVista UR Setup software in online mode or by using any of the supported file transfer protocols. Note that TFTP cannot be used here, as TFTP "put" mode is disabled for security reasons. 10-8 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 577 Manually copy the remaining settings, outlined as follows. To restore settings from an IID file using EnerVista software: In Windows, make a copy the IID file with a cid extension. Connect to the device in the Online Window area. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-9...
Page 578: Upgrade Software
UR 7.4 can be used to access multiple UR devices that have version 7.4x, 7.2x, and 6.0x firmware installed. Existing installations do not need to be uninstalled before upgrade. You can also downgrade the software; use the same procedure. 10-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 579: Upgrade Firmware
If upgrading both EnerVista software and F60 firmware, upgrade the software first. The firmware of the F60 device can be upgraded, locally or remotely, using the EnerVista software. Upgrades are possible for the same release (such as 7.01 to 7.02) and from one firmware version to another (such as 7.2 to 7.3).
Page 580: Replace Module
To avoid damage to the equipment, use proper electrostatic discharge protection (for example, a static strap) when coming in contact with modules while the relay is energized. 10-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 581 Open the enhanced faceplate to the left once the thumb screw has been removed. This allows for easy access of the modules for withdrawal. The new wide-angle hinge assembly in the enhanced front panel opens completely and allows easy access to all modules in the F60. Figure 10-10: Modules inside relay with front cover open (enhanced faceplate) The standard faceplate can be opened to the left once the black plastic sliding latch on the right side has been pushed up, as shown below.
Page 582: Battery
Replace the battery with the identical make and model. For example, do not use a rechargeable battery. Observe the + and - polarity of the battery and replace it with the same polarity as marked on the battery holder. 10-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 583: Dispose Of Battery
Batteriet er forsynet med indgraveret symboler for hvad batteriet indeholder: kadmium (Cd), bly (Pb) og kviksølv (Hg). Europæiske brugere af elektrisk udstyr skal aflevere kasserede produkter til genbrug eller til leverandøren. Yderligere oplysninger findes på webstedet www.recyclethis.info. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-15...
Page 584 (Cd), ólom (Pb) vagy higany (Hg) tartalomra utaló betűjelzés. A hulladék akkumulátor leadható a termék forgalmazójánál új akkumulátor vásárlásakor, vagy a kijelölt elektronikai hulladékudvarokban. További információ a www.recyclethis.info oldalon. 10-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 585 (Cd), chumbo (Pb), ou o mercúrio (hg). Para uma reciclagem apropriada envie a bateria para o seu fornecedor ou para um ponto de recolha designado. Para mais informação veja: www.recyclethis.info. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL 10-17...
Page 586: Clear Files And Data After Uninstall
+86-21-2401-3208 India +91 80 41314617 From GE Part Number 1604-0021-A1, GE Publication Number GEK-113574. 10.10 Clear files and data after uninstall The unit can be decommissioned by turning off power to the unit and disconnecting the wires to it. Files can be cleared after uninstalling the EnerVista software or UR device, for example to comply with data security regulations.
Page 587: Repairs
Customers are responsible for shipping costs to the factory, regardless of whether the unit is under warranty. • Fax a copy of the shipping information to the GE Grid Solutions service department in Canada at +1 905 927 5098. Use the detailed return procedure outlined at https://www.gegridsolutions.com/multilin/support/ret_proc.htm...
Page 588: Disposal
Other than the battery, there are no special requirements for disposal of the unit at the end its service life. For customers located in the European Union, dispose of the battery as outlined earlier. To prevent non-intended use of the unit, remove the modules, dismantle the unit, and recycle the metal when possible. 10-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 589: A.1 Flexanalog Items
Field RTD 8 Value Field RTD 8 value 5832 Field TDR 1 Value Field TDR 1 value 5834 Field TDR 2 Value Field TDR 2 value 5836 Field TDR 3 Value Field TDR 3 value F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 590 6228 SRC 2 Ig RMS Amps Source 2 ground current RMS 6230 SRC 2 Ig Mag Amps Source 2 ground current magnitude 6232 SRC 2 Ig Angle Degrees Source 2 ground current angle F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 591 6358 SRC 4 Ig Mag Amps Source 4 ground current magnitude 6360 SRC 4 Ig Angle Degrees Source 4 ground current angle 6361 SRC 4 I_0 Mag Amps Source 4 zero-sequence current magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 592 SRC 2 Vbc RMS Volts Source 2 phase BC voltage RMS 6739 SRC 2 Vca RMS Volts Source 2 phase CA voltage RMS 6741 SRC 2 Vab Mag Volts Source 2 phase AB voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 593 SRC 4 Vag Mag Volts Source 4 phase AG voltage magnitude 6856 SRC 4 Vag Angle Degrees Source 4 phase AG voltage angle 6857 SRC 4 Vbg Mag Volts Source 4 phase BG voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 594 Source 2 phase B reactive power 7214 SRC 2 Qc Vars Source 2 phase C reactive power 7216 SRC 2 S Source 2 three-phase apparent power 7218 SRC 2 Sa Source 2 phase A apparent power F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 595 SRC 2 Demand Ib Amps Source 2 phase B current demand 7700 SRC 2 Demand Ic Amps Source 2 phase C current demand 7702 SRC 2 Demand Watt Watts Source 2 real power demand F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 596 SRC 1 Vb Harm[12] Source 1 phase B voltage twelfth harmonic 8101 SRC 1 Vb Harm[13] Source 1 phase B voltage thirteenth harmonic 8102 SRC 1 Vb Harm[14] Source 1 phase B voltage fourteenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 597 SRC 2 Va Harm[9] Source 2 phase A voltage ninth harmonic 8148 SRC 2 Va Harm[10] Source 2 phase A voltage tenth harmonic 8149 SRC 2 Va Harm[11] Source 2 phase A voltage eleventh harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 598 SRC 2 Vc Harm[6] Source 2 phase C voltage sixth harmonic 8195 SRC 2 Vc Harm[7] Source 2 phase C voltage seventh harmonic 8196 SRC 2 Vc Harm[8] Source 2 phase C voltage eighth harmonic A-10 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 599 Fault 1 pre-fault phase B voltage magnitude 9038 Prefault Vb Ang [1] Degrees Fault 1 pre-fault phase B voltage angle 9039 Prefault Vc Mag [1] Volts Fault 1 pre-fault phase C voltage magnitude F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-11...
Page 600 Phasor measurement unit 1 phase B voltage angle 9587 PMU 1 Vc Mag Volts Phasor measurement unit 1 phase C voltage magnitude 9589 PMU 1 Vc Angle Degrees Phasor measurement unit 1 phase C voltage angle A-12 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 601 SRC 1 Ia Harm[20] Source 1 phase A current twentieth harmonic 10260 SRC 1 Ia Harm[21] Source 1 phase A current twenty-first harmonic 10261 SRC 1 Ia Harm[22] Source 1 phase A current twenty-second harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-13...
Page 602 SRC 1 Ic Harm[17] Source 1 phase C current seventeenth harmonic 10323 SRC 1 Ic Harm[18] Source 1 phase C current eighteenth harmonic 10324 SRC 1 Ic Harm[19] Source 1 phase C current nineteenth harmonic A-14 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 603 SRC 2 Ib Harm[14] Source 2 phase B current fourteenth harmonic 10386 SRC 2 Ib Harm[15] Source 2 phase B current fifteenth harmonic 10387 SRC 2 Ib Harm[16] Source 2 phase B current sixteenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-15...
Page 604 SRC 3 Ia Harm[11] Source 3 phase A current eleventh harmonic 10449 SRC 3 Ia Harm[12] Source 3 phase A current twelfth harmonic 10450 SRC 3 Ia Harm[13] Source 3 phase A current thirteenth harmonic A-16 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 605 SRC 3 Ic Harm[8] Source 3 phase C current eighth harmonic 10512 SRC 3 Ic Harm[9] Source 3 phase C current ninth harmonic 10513 SRC 3 Ic Harm[10] Source 3 phase C current tenth harmonic F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-17...
Page 606 SRC 4 Ib Harm[5] Source 4 phase B current fifth harmonic 10575 SRC 4 Ib Harm[6] Source 4 phase B current sixth harmonic 10576 SRC 4 Ib Harm[7] Source 4 phase B current seventh harmonic A-18 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 607 Volts Synchrocheck 1 delta voltage 10850 Synchchk 1 Delta Phs Degrees Synchrocheck 1 delta phase 10851 Synchchk 1 Synchscp Degrees Synchrocheck 1 synchscope 10852 Synchchk 1 Delta F Synchrocheck 1 delta frequency F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-19...
Page 608 Breaker 1 Acc arcing amp phase A 12034 Brk 1 Acc Arc Amp B kA2-cyc Breaker 1 Acc arcing amp phase B 12036 Brk 1 Acc Arc Amp C kA2-cyc Breaker 1 Acc arcing amp phase C A-20 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 609 DCmA input 7 actual value 13518 DCmA Ip 8 DCmA input 8 actual value 13520 DCmA Ip 9 DCmA input 9 actual value 13522 DCmA Ip 10 DCmA input 10 actual value F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-21...
Page 610 RTD input 30 actual value 13582 RTD Ip 31 RTD input 31 actual value 13583 RTD Ip 32 RTD input 32 actual value 13584 RTD Ip 33 RTD input 33 actual value A-22 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 611 45606 RxGOOSE Analog 12 RxGOOSE analog input 12 45608 RxGOOSE Analog 13 RxGOOSE analog input 13 45610 RxGOOSE Analog 14 RxGOOSE analog input 14 45612 RxGOOSE Analog 15 RxGOOSE analog input 15 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-23...
Page 612 Volts HIZ Ig harmonics 10 63278 HZ Ig Harmonics[11] Volts HIZ Ig harmonics 11 63279 HZ Ig Harmonics[12] Volts HIZ Ig harmonics 12 63280 HZ Ig Harmonics[13] Volts HIZ Ig harmonics 13 A-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 613 Volts HIZ Ig harmonics 57 63325 HZ Ig Harmonics[58] Volts HIZ Ig harmonics 58 63326 HZ Ig Harmonics[59] Volts HIZ Ig harmonics 59 63327 HZ Ig Harmonics[60] Volts HIZ Ig harmonics 60 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL A-25...
Page 614 Volts HIZ Ig harmonics 61 63329 HZ Ig Harmonics[62] Volts HIZ Ig harmonics 62 63330 HZ Ig Harmonics[63] Volts HIZ Ig harmonics 63 63331 HZ Ig Harmonics[64] Volts HIZ Ig harmonics 64 A-26 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 615: B.1 Radius Server Configuration
UR device for successful authentication, and the shortname is a short, optional alias that can be used in place of the IP address. client 10.0.0.2/24 { secret = testing123 shortname = private-network-1 In the <Path_to_Radius>\etc\raddb folder, create a file called dictionary.ge and add the following content. # ########################################################## GE VSAs ############################################################ VENDOR...
Page 616 8.2. Access Settings > Product Setup > Security. Configure the IP address and ports for the RADIUS server. Leave the GE vendor ID field at the default of 2910. Update the RADIUS shared secret as specified in the clients.conf file.
Page 617: C.1 Command Line Interface
This setting cannot be changed using the command line interface. • Use quotes ("") to enclose any parameter containing a space • Commands, options, and parameters are case sensitive F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 618 For non-CyberSentry devices — Set <authentication type> to "traditional". Note that <authentication type> defaults to "traditional" if not specified. Set <account> to "COMMANDS" or "SETTINGS". If not specified, the SETTINGS account is used. Example: SetupCLI URPC login -d "C30 Melbourne" -A traditional -a SETTINGS -w 1password1 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 619 SetupCLI <Application> getsettings -d <device> -f <File> [-s] Read settings from device <device> and save them to the .urs file <File>. The <File> must not already exist. The default path to the output file is C:\Users\Public\Documents\GE Power Management\URPC\Data Example: SetupCLI URPC getsettings -d C30 -f "C30 Markham.urs"...
Page 620 SetupCLI URPC getsettings -d demoDevice -f devicefile.urs SetupCLI URPC compare -f existingfile.urs -r devicefile.urs -o output.txt The output is similar to the following: Comparing settings file aaa.urs : C:\Users\Public\Documents\GE Power Management\URPC\Data\ with bbb.urs : C:\Users\Public\Documents\GE Power Management\URPC\Data\ Setting Name (Group,Module,Item) Value...
Page 621 SetupCLI URPC getsettings -d DEV@SETUP_CLI -f "example file.urs" SetupCLI URPC logout -d DEV@SETUP_CLI SetupCLI URPC exit DEV@SETUP_CLI has to be used as the device name in the commands followed by the 'adddevice' command. F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 622 COMMAND LINE INTERFACE APPENDIX C: COMMAND LINE INTERFACE F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 623: D.1 Warranty
D.1 Warranty For products shipped as of 1 October 2013, GE Grid Solutions warrants most of its GE manufactured products for 10 years. For warranty details including any limitations and disclaimers, see the GE Grid Solutions Terms and Conditions at https://www.gegridsolutions.com/multilin/warranty.htm...
Page 624 30 March 2013 13-0126 1601-0093-AA1 7.2x 1 August 2013 13-0401 1601-0093-AB1 7.3x 7 November 2014 14-1408 1601-0093-AB2 7.3x 1 September 2015 15-2215 1601-0093-AC1 7.40x 8 December 2016 16-3319 1601-0093-AE1 7.41x 31 January 2017 17-3427 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 625 Modbus memory map, IMD tables. Did not add Single-Pole Tripping section to Theory of Operation chapter because single-pole tripping does not apply to F60. Did not add new Application of Settings chapter to add Protection Signaling Schemes section because section is POTT and not Pilot POTT.
Page 626 REVISION HISTORY APPENDIX D: MISCELLANEOUS Table D-4: Major changes for F60 manual version AB2 (English) Page Description Updated document throughout, including numbers of elements and FlexLogic operands table Added EAC compliance information throughout, including logo on title page, rear panel, added specifications, added life...
Page 627 Contact Output FREQ Frequency Communication Frequency-Shift Keying COMM Communications File Transfer Protocol COMP Compensated, Comparison FlexElement™ CONN Connection Forward CONT Continuous, Contact CO-ORD Coordination Generator Central Processing Unit GDOI Group Domain of Interpretation F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 628 Permissive Under-reaching Transfer Trip Manual / Manually Pulse Width Modulated Maximum Power Model Implementation Conformance Minimum, Minutes QUAD Quadrilateral Man Machine Interface Manufacturing Message Specification Rate, Reverse Minimum Response Time Registration Authority Message Reach Characteristic Angle F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 629 Transport Selector Time Undercurrent Time Undervoltage TX (Tx) Transmit, Transmitter Under Undercurrent Utility Communications Architecture User Datagram Protocol Underwriters Laboratories UNBAL Unbalance Universal Relay Universal Recloser Control .URS Filename extension for settings files Undervoltage F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 630 ABBREVIATIONS F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 632 RS485 ..................3-27, 5-29 Certification .................... 2-38 settings ..................5-32, 5-39 Changes ......................D-1 specifications ................. 2-34, 2-35 Channel timeout ....................5-39 banks ....................5-129 web server ................... 5-86 tests ......................6-10 Compare settings ................10-5 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 633 IEEE .......................5-196 Device setup ..................3-59 inverse time undervoltage ............5-241 Dielectric strength ................3-10 types ....................5-195 Digital counters Cutout, panel ...................3-2, 3-3 actual values ..................6-7 FlexLogic operands ...............5-173 logic diagram ...................5-281 settings ....................5-279 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 635 FlexLogic operands ...............5-173 FlexAnalog parameters ..............A-1 logic diagram ...................5-264 FlexCurves settings ....................5-263 equation .....................5-200 specifications ..................2-24 settings ....................5-141 Frequency testing ..................8-1 specifications ..................2-26 Frequency tracking ................6-24 table .....................5-141 Frequency, nominal .................5-130 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 636 URs ..........2-7 IEC 61850-90-5 self-test errors ................... 7-13 actual values ..................6-26 Harmonic content ................6-22 IEC 61850-90-5 protocol Harmonics explained ................... 5-148 actual values ..................6-22 settings ....................5-153 FlexAnalogs ..................A-24 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 642 System logs .................... 5-25 metering ....................6-17 System requirements ................ 3-48 settings ....................5-131 System setup ..................5-129 Simulation bit ..................5-334 Single-line diagram ................2-2 Site Targets ..................... 10-1 Smart defaults ..................5-102 Target messages ..................7-7 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 645 INDEX Zero-sequence core balance ............3-13 F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...
Page 646 INDEX F60 FEEDER PROTECTION SYSTEM – INSTRUCTION MANUAL...

GE F60 Instruction Manual

1 Introduction

Safety Symbols and Definitions

2 Product Description

3 Installation

Unpack and Inspect

4 Interfaces

Enervista Software Interface

5 Settings

Settings Menu

6 Actual Values

Actual Values Menu

7 Commands and Targets

8 Commissioning

Testing

9 Theory of Operation

10 Maintenance

Back up and Restore Settings

Upgrade Software

Quick Links

Related Manuals for GE F60

Summary of Contents for GE F60