Table of Contents
Advertisement
9. Before installation, remove all silicone gaskets (if present) from the joints of the pellet pipe, and dispose of
the gaskets appropriately. All joints must be secured with at least 3 self-tapping screws per joint.
!
10. CANADA: No chimney connector shall pass through an attic or roof space, closet, or similar concealed
space, or a floor, or ceiling. Where passage through a wall, or partition of combustible construction is
desired, the installation shall conform to CAN/CSA-B365, Installation Code for Solid-Fuel-Burning Appliances
and Equipment.
!
11. CAUTION: WHEN VENTING WITH THIS APPROVED CHIMNEY SYSTEM, FOLLOW ONLY THESE
INSTALLATION INSTRUCTIONS FOR CONNECTING THE KIMBERLY™ WOOD STOVE HEATER.
!
12. CAUTION: NEVER FOLLOW INSTALLATION INSTRUCTIONS OR CLEARANCE RECOMMENDATIONS
WHICH MAY BE PROVIDED BY ANY PELLET PIPE MANUFACTURER.
!
13. CAUTION: BEFORE INSTALLATION, REMOVE ALL SILICONE GASKETS FROM THE JOINTS OF ANY
PELLET PIPE (IF PRESENT) AND DISPOSE OF THE GASKETS APPROPRIATELY.
!
14. CAUTION: DO NOT USE A REDUCER TO JOIN THE 3-INCH PELLET PIPE WITH THE 6-INCH CLASS-A
PIPE. NOTE: THE 3-INCH PELLET PIPE WILL CARRY THE FLUE GASES FROM THE STOVE TO THE
TOP OF THE CHIMNEY. THE 6-INCH CLASS-A PIPE IS USED AS A CONDUIT FOR THE 3-INCH PELLET
PIPE. THE 3-INCH PELLET PIPE SHOULD TERMINATE FLUSH WITH THE 6-INCH CLASS-A PIPE OR
TERMINATE A FEW INCHES ABOVE THE 6-INCH CLASS-A PIPE. THE 3-INCH PELLET PIPE SHOULD
NEVER TERMINATE BELOW THE 6-INCH CLASS-A PIPE.
!
15. CAUTION: NEVER UTILIZE MAKE-SHIFT COMPROMISES DURING INSTALLATION. NEVER INSTALL
ANY WOOD STOVE OR CHIMNEY SYSTEMS OUTSIDE OF THE PROVISIONS OUTLINED IN THE
NFPA-211 SAFETY STANDARDS (OR CANADIAN EQUIVALENT).
!
ADDITIONAL REQUIREMENTS FOR MOBILE HOME INSTALLATIONS IN THE U.S.A.
!
1. The Kimberly™ wood stove heater must be bolted to the mobile home chassis, using the three pre-drilled
holes at the base of the Kimberly™ wood stove heater, and three 1/2-inch hex-head bolts of 1/4-inch
diameter and 2-1/2 inches long (or the metric equivalent) which may be purchased at a hardware store.
!
2. All U.S.A. mobile home installations require an outside air kit (OAKP or OAKL) to provide the Kimberly™
wood stove heater with a supply of outside combustion air. The Kimberly™ wood stove heater has a 2-inch
(5.1 cm) air inlet under the base of the stove to accommodate such a kit. The Kimberly™ wood stove heater
may include an additional air inlet at the back of the stove. Use one outside combustion air inlet or the other,
but not both.
!
3. Choose a location for the outside air inlet that will not interfere with bolting the Kimberly™ wood stove heater
to the mobile home chassis. To discourage entry by insects and rodents, the outside air inlet should be
protected by a fine mesh screen on the external end.
!
4. U.S.A.: All mobile home installations require that the Kimberly™ wood stove heater must be electrically
grounded to the chassis, and the chimney must include a spark arrester cap.
!
5. CANADA: The Kimberly™ wood stove heater is not approved for mobile home use in Canada.
!
6. CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF
MUST BE MAINTAINED.
!
7. CAUTION: USE ALL INSTALLATION COMPONENTS AS SPECIFIED IN THIS MANUAL. NEVER OMIT ANY
PARTS OR SUBSTITUTE WITH OTHER COMPONENTS.
!
8. CAUTION: THE INTEGRITY OF ANY VAPOR BARRIERS MUST BE MAINTAINED.
!
9. CAUTION: DO NOT INSTALL IN SLEEPING ROOM.
!
Kimberly™ Owner's Manual
6
www.UnforgettableFireLLC.com
- Quick Links:
- Clearance to Combustibles
Hide quick links:
Advertisement
Table of Contents
