Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Pioneer CDJ-1000MK2
Summary of Contents for Pioneer CDJ-1000MK2
- Page 1 COMPACT DISC PLAYER CDJ-1000MK2 Operating Instructions...
- Page 2 NOTE: THE NO USER-SERVICEABLE PARTS COMPARTMENT WARNING IS LOCATED ON THE APPLIANCE BOTTOM. <DRB1339>...
- Page 3 [For U.S. model] IMPORTANT NOTICE The serial number for this equipment is located in the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. WARNING: Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California...
-
Page 4: Table Of Contents
CD lens cleaner The player’s pickup lens should not become dirty in normal use. If for some rea- son, the lens becomes soiled and malfunctions, contact your nearest PIONEER authorized service center. Lens cleaners for CD players are commercially available, but special care should be exercised in their use as some may cause damage to the lens. -
Page 5: Storing Discs
When performing forced ejection, be sure to follow the precautions below. 1 Be sure to turn OFF the power of the CD player, and check that the disc has stopped rotating. It takes about 60 seconds for the disc to stop rotating after the power has been turned OFF. -
Page 6: Features
BEFORE OPERATIONS FEATURES The CDJ-1000MK2 compact disc player is designed for use by DJs providing all the functions and performance required in disco clubs while offering performance, sound quality and functionality superior to any analog player. JOG DIAL The large 206 mm diameter Jog dial enables better handling than an analog turntable. -
Page 7: Connections
Connect the supplied control cord to enable control of the unit from the mixer to allow fader start play and back cue. Connecting DJM-600 CDJ-1000MK2 ÷ Connections for the DJM-300 and DJM-500 are similar; use the supplied audio cables to connect the mixer’s CD1 jacks to Player A, and CD2 jacks to Player B. -
Page 8: Connecting To Other Devices
7 Setting the DIGITAL OUT Mode Switch (rear panel) When the unit is used normally as a DJ CD Player, this switch should be set to DJ. When set to DJ: ÷ The DIGITAL OUT connector outputs only audio data without sub-codes. The mode, however, is fixed at 44.1 kHz. -
Page 9: Panel Facilities
PANEL FACILITIES Top Panel 1 DISPLAY CD TEXT/WAVE (ZOOM) button (*) Each press of this button toggles the display between WAVE display and CD-TEXT disc/track title display. When the button is held down for 1 second or longer, the WAVE display cycles between the 1 track full-scale and 2x zoom scale. 2 TIME MODE/AUTO CUE button (*) TIME MODE: Each time this button is pressed, the time display changes between elapsed play-... -
Page 10: Display
BEFORE OPERATIONS: PANEL FACILITIES 28 Force Ejection Hole 29 Memory Card Loading Slot P.16 30 Memory Card indicator P.16 Lights when the MMC card is being accessed. ¶ Do not remove the card or turn off the power when this lamp is on. 31 Play/Pause indicator Lights during play and flashes during pause. -
Page 11: Disc Loading/Unloading
1 When playing CD singles (8 cm/3-inch discs), always use the adapter for 8 cm/3-inch discs. Before loading the disc into the CD player, be sure to check that it is secured properly by the catches of the adapter. If discs have been inserted without the adapter by mistake, remove the disc immediately by pressing the EJECT button. -
Page 12: Stopping Playback
CUE button (back cue) before pressing the EJECT button (0) to eject the disc. ¶ Playback will stop and the disc will be ejected. ¶ Note that the CDJ-1000MK2 does not come with a stop button. To Pause Play During playback, press the PLAY/PAUSE button (6). -
Page 13: Changing Playback Speed
[Amending the Cue point] 1. During playback, press the CUE button. ¶ This will take you back to the set track position. 2. In the VINYL mode, to set the Cue point, go through steps 2 and 3 as mentioned above. ÷... -
Page 14: Advanced Operations
ADVANCED OPERATIONS 7 Fader start play Using the cross fader start function of the DJM-600, DJM-500, DJM-300 or DJM-3000, step 10 above can be eliminated for even simpler mixing. In addi- ADVANCED OPERATIONS LOOP IN/REALTIME LOOP OUT CUE (IN ADJUST) (OUT ADJUST) HOT CUE A HOT CUE B... -
Page 15: Reversing Playback
(See page. 7 for instructions on how to connect the player.) Relay Play Using Two Players (*) If you connect the terminals of this player with another CDJ series CD player using the supplied control cord then you will be able to relay play. -
Page 16: Using Cue Points/Loop Points Memory
ADVANCED OPERATIONS USING CUE POINTS/LOOP POINTS MEMORY This unit can store Cue points and Loop points for each disc in internal or on a Multimedia Card (MMC). Using Internal Memory When a Multimedia Card (MMC) is not inserted in the card slot, the internal memory is used. -
Page 17: Copying Mmc Data
7 Storing CUE points Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. 7 Storing Loop points Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. -
Page 18: Troubleshooting
8cm disc and adaptor are used. This is NOT a malfunction. ¶ The BPM value measured by the CDJ-1000MK2 may differ from the BPM value recorded on a CD or from our DJ mixer, but this difference is a result of differences in the BPM value measurement method;... -
Page 19: Error Message Display
Error message display When the CDJ-1000MK2 CD player is unable to operate properly, an error code is displayed on the display panel. Check the error code displayed against the follow- ing table and take the recommended action to correct the error. If an error code... -
Page 20: Specifications
Distortion ... 0.006% (JEITA) PIONEER CORPORATION 4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. Multimedia and Mass Storage Division: PIONEER ELECTRONICS OF CANADA, INC. Industrial Products Department: 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada <DRB1339> <TSZZW/03D00000>...