Advertisement
Z3 Installation Guide [Internal]
This document describes how to install and set up the Z3 teleworker gateway. Additional reference documents are
available online at: www.meraki.com/library/products.
Z3 Overview
The Meraki Z3 is an enterprise teleworker gateway designed for telecommuting employees and IT staff. It is also a great
all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway provides the following
features:
• Support for four LAN connections
• Dual-concurrent 802.11ac radios for wireless connections
• Wall screws and anchors for mounting drywall surface, either vertically or horizontally
Package contents
In addition to the Z3, the following are provided.
1
Advertisement
Table of Contents
Related Manuals for Cisco Meraki Z3
Summary of Contents for Cisco Meraki Z3
-
Page 1: Package Contents
Z3 Overview The Meraki Z3 is an enterprise teleworker gateway designed for telecommuting employees and IT staff. It is also a great all-in-one device to test the capabilities of Meraki's cloud-managed networking. This gateway provides the following features: •... -
Page 2: The Z3 Front Panel
The Z3 front panel Ports and Status Indicators The Z3 uses a single LED to inform the user of the device's status. LED Status Meaning Flashing white Operation in progress Solid white Power is applied, Fully operational The Z3 back panel Additional functions on the back panel are described below, from left to right. - Page 3 Insert a paper clip if a reset is required. • A brief, momentary press: To delete a downloaded configuration and reboot. Reset button • Press and hold for more than 10 sec: To force the unit into a full factory reset. These 4 ports provide connectivity to computers, printers, access points, or Ethernet switches.
-
Page 4: The Z3 Bottom Panel
The Z3 bottom panel... -
Page 5: Mounting Hardware
Connecting to WAN All Meraki Z3 devices must have an IP address. This section describes how to configure your local area network before you deploy it. A local management web service, running on the gateway, is accessed through a browser running on a... -
Page 6: Setting Up A Static Ip Address
Setting up a static IP address To ensure that the client PC is redirected to the local web service in the following step, you must disable all other network services (ex: wi-fi) on your client machine. Do the following to configure basic connectivity and other networking parameters: 1. - Page 7 10- or 100-Mbps data rates. Power efficiency modes The Meraki Z3 Teleworker Appliance has an off mode and a networked standby or efficient idle mode, both with power consumption less than 12W.
- Page 8 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 9 préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Industry Canada Caution (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;...
- Page 10 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾 時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 電磁波曝露量MPE標準值1mW/cm ，本產品使用時建議應距離人體 20 cm。 1. 使用此產品時應避免影響附近雷達系統之操作。 2. 高增益指向性天線只得應用於固定式點對點系統。...