Page 1
XT-P50V SERVICE MANUAL AEP Model UK Model Ver 1.0 2002.09 E Model Australian Model Chinese Model The XT-P50V is composed of the following models. TV tuner unit XT-P50V TV Antenna VCA-116 Wireless Remote Commander RM-X124 SPECIFICATIONS Wireless remote commander RM-X124...
To the power remote cord (blue) of the monitor* Blue (when connected to the monitor) Blau * If the Sony BUS connection is used, this connection is not necessary. an Stromversorgungskabel (blau) eines Monitors* (bei Anschluss an einen Monitor)
Page 3
XT-P50V RCA interconnects 3 (5.3 m) Bus cable 2 (5.3 m) Cinch-Verbindungen 3 (5,3 m) Buskabel 2 (5,3 m) Leave clearance of at least 50 mm. Mindestens 50 mm Abstand lassen. Short CONTROL Kurz OUTPUT CONTROL Do not bend sharply.
Page 4
The XAV-7W is shown for the Sony BUS connection and the • Do not wipe the aerial body, rods, or cables with alcohol, installation. Wet conditions will reduce the adhesive strength XVM-R75 is shown for the other connection in this operating and may cause the aerials to fall off.
TEST MODE ELECTRICAL ADJUSTMENTS MICROPROCESSOR VERSION CHECK DIVERSITY VCO FREQUENCY ADJUSTMENT Connection: Checking Method: 1. Set TV SYSTEM switch of XT-P50V to 2. frequency 2. Connect XAV-7W and turn on the power for OFF screen sta- counter TP130 tus. TV Tuner Unit 3.
Page 6
XT-P50V Adjusting and Connecting Location: – HIDEAWAY BOARD (Component Side) – J104 INPUT VIDEO jack RV100 OSD Adjustment CT100 Diversity VCO Frequency Adjustment – HIDEAWAY BOARD (Conductor Side) – TP139 TP130 TP131...
XT-P50V SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM – AUDIO Section – L101 L103 L102 VIDEO +31V (Page 8) ANT IN NOISE CANCELLER IC104 +B 9V, +B 9V, +B 5V, VIDEO • R-ch is omitted due to same as L-ch. 35mA...
XT-P50V 4-2. BLOCK DIAGRAM – VIDEO Section – VIDEO SELECT SWITCH, ON SCREEN DISPLAY VIDEO AMP VIDEO AMP CONTROLLER IC106 IC109 IC110 VIDEO J103 (2/2) V OUT OUTPUT1 (Page 7) 10 CVIN VOUT VIDEO J103 (2/2) DATA INPUT CONTROL VIN2...
XT-P50V 4-3. BLOCK DIAGRAM – BUS CONTROL/POWER SUPPLY Section – BUS ON/OFF SWITCH Q109 CN101 CONTROL CN103 (FOR CHECK) SONY BUS (SONY BUS) INTERFACE LINKOFF IC101 SIRCS CLK OUT SCLK SCLK CLOCK UNI CLK DATA DATA OUT DATA UNI SI...
XT-P50V 4-4. NOTE FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAMS • Waveforms Note on Printed Wiring Board: Note on Schematic Diagram: 1 IC100 1 (CT) 6 Q200-1 (Drain) qa IC113 3 • X : parts extracted from the component side.
XT-P50V 4-5. SCHEMATIC DIAGRAM – HIDEAWAY Board (1/3) – • • See page 10 for Waveforms. See page 16 for IC Block Diagrams. TU100 (1/3) TV TUNER UNIT (V5-E60CT) ANT IN Q100 Q103 ANTENNA 1 SWITCH ANTENNA 3 SWITCH Q101...
Battery detection signal input “H”: battery on BUCKUP VPP signal input terminal System reset signal input from the SONY bus interface and reset signal generator “L”: reset RESET For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”...
Page 19
XT-P50V Pin No. Pin Name Description Destination setting terminal of TV tuner unit NICAM Normally: fixed at “L”, “H”: hong kong and south africa area models N.C.O Not used OSD data clear control signal output to the on screen display controller “L”: all clear 55, 56 N.C.O...
XT-P50V SECTION 5 EXPLODED VIEW NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they may have some difference from the original are seldom required for routine service. Some one. delay should be anticipated when ordering •...
XT-P50V SECTION 6 ELECTRICAL PARTS LIST HIDEAWAY NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they When indicating parts by reference parts list may be different from the parts speci- are seldom required for routine service.