YASKAWA E7 Installation Manual

Ig.e7.03

Hide thumbs Also See for E7:

Instruction manual and parameter description (290 pages)

Operating manual (216 pages)

User manual (204 pages)

Table Of Contents

See also: Technical Manual , User Manual

Purpose:

This document describes wiring terminals, main circuit terminal connections and main circuit terminal wiring specifications

for the standard E7 drive.

The contents of this document are included in the E7 User Manual TM.E7.01:

• Chapter 2, pages 2-1 through 2-7

• Section: Wiring Main Circuit Terminals

• Table 2.1 208-240Vac Wire Sizes and Connector Specifications

• Table 2.2 480Vac Wire Sizes and Connector Specifications

Information in this document supercedes that contained in TM.E7.01 with dates 5/1/06, Rev: 06-05, and earlier. The data in

this document reflects the most recent information provided by Yaskawa regarding these specific wire size tables.

This document is subject to change without notice. The latest version of this document can be obtained from the Yaskawa

website www.yaskawa.com by entering IG.E7.03 into the Yaskawa site search.

Applicability:

This document applies to the following models of E7 drives:

CIMR-E7U20P4

CIMR-E7U20P7

CIMR-E7U21P5

CIMR-E7U22P2

CIMR-E7U23P7

CIMR-E7U25P5

CIMR-E7U27P5

CIMR-E7U2011

CIMR-E7U2015

CIMR-E7U2018

CIMR-E7U2022

CIMR-E7U2030

CIMR-E7U2037

CIMR-E7U2045

CIMR-E7U2055

CIMR-E7U2075

CIMR-E7U2090

CIMR-E7U2110

Document Number: IG.E7.03 07/11/06

Data subject to change without notice. Yaskawa Electric America, Inc.

CIMR-E7U40P4

CIMR-E7U40P7

CIMR-E7U41P5

CIMR-E7U42P2

CIMR-E7U43P7

CIMR-E7U45P5

CIMR-E7U47P5

CIMR-E7U49P0

CIMR-E7U4011

CIMR-E7U4015

CIMR-E7U4018

CIMR-E7U4024

CIMR-E7U4030

CIMR-E7U4037

CIMR-E7U4045

CIMR-E7U4055

CIMR-E7U4075

CIMR-E7U4090

CIMR-E7U4110

CIMR-E7U4160

CIMR-E7U4185

CIMR-E7U4220

CIMR-E7U4300

Rev. 06-07

Installation Guide for E7 Drives

IG.E7.03

Table of Contents

Summary of Contents for YASKAWA E7

Page 1 • Table 2.2 480Vac Wire Sizes and Connector Specifications Information in this document supercedes that contained in TM.E7.01 with dates 5/1/06, Rev: 06-05, and earlier. The data in this document reflects the most recent information provided by Yaskawa regarding these specific wire size tables.
Page 2 Chapter 2 Electrical Installation This chapter describes wiring terminals, main circuit terminal connections, main circuit terminal wiring specifications, control circuit terminals, and control circuit wiring specifications. Terminal Block Configuration ............. 2-2 Wiring Main Circuit Terminals ........... 2-3 Control Wiring................2-12 Electrical Installation 2 - 1...
Page 3: Terminal Block Configuration
Terminal Block Configuration The wiring terminals are shown in Fig 2.1. E(G) E(G) Control circuit terminals Main circuit terminals Charge indicator Ground terminal Ground terminal Models CIMR-_ _ _2018 (25 HP, 208V)/ 4018 (30 HP, 480V) and smaller E(G) E(G) Control circuit terminals Charge indicator Main circuit terminals...
Page 4: Wiring Main Circuit Terminals
Wiring Main Circuit Terminals Applicable Wire Sizes and Closed-loop Connectors Select the appropriate wires and crimp terminals from Table 2.1 to Table 2.2. Table 2.1 208-240Vac Wire Sizes and Connector Specifications Recommended Clamping Wire Size Drive Model Nominal Terminal Torque Wire Terminal Symbol CIMR-E7U...
Page 5 Table 2.1 208-240Vac Wire Sizes and Connector Specifications Recommended Clamping Wire Size Drive Model Nominal Terminal Torque Wire Terminal Symbol CIMR-E7U Screws lb. in. Type (N•m) R/L1, S/L2, T/L3, 1 U/T1, (22.5) (100) V/T2, W/T3, R1/L11, S1/L21, T1/L31 88.5 (10.0) (22) 2037 203.6...
Page 6 Table 2.2 480Vac Wire Sizes and Connector Specifications Clamping Recommended Drive Model Nominal Terminal Torque Wire Size AWG Terminal Symbol Wire Type CIMR-E7U Screws lb. in. (N•m) R/L1, S/L2, T/L3, 13.3 B1, B2, U/T1, V/T2, W/T3 40P4 0.5/0.75 (1.5) (2.1) R/L1, S/L2, T/L3, 13.3 B1, B2, U/T1, V/T2, W/T3...
Page 7 Table 2.2 480Vac Wire Sizes and Connector Specifications Clamping Recommended Drive Model Nominal Terminal Torque Wire Size AWG Terminal Symbol Wire Type CIMR-E7U Screws lb. in. (N•m) 88.5 R/L1, S/L2, T/L3, 1, U/T1, V/T2, (10.0) (33.6) W/T3, R1/L11, S1/L21, T1/L31 44.3 4055 (5.0)
Page 8 Table 2.2 480Vac Wire Sizes and Connector Specifications Clamping Recommended Drive Model Nominal Terminal Torque Wire Size AWG Terminal Symbol Wire Type CIMR-E7U Screws lb. in. (N•m) 88.5 300 X 2P R/L1, S/L2, T/L3, (10.0) (152 X 2P) 88.5 300 X 2P U/T1, V/T2, W/T3, R1/L11, S1/L21, T1/L33 (10.0) (152 X 2P)
Page 9: Main Circuit Terminal Functions
Main Circuit Terminal Functions Main circuit terminal functions are summarized according to terminal symbols in Table 2.3. Wire the terminals correctly for the desired purpose. Table 2.3 Main Circuit Terminal Functions (208-240Vac and 480Vac) Model: CIMR-E7U _ _ _ _ Purpose Terminal Designation 208-240Vac...
Page 10 (See Appendix E) may result in damage to the wiring, Drive and/or personal injury. 2. Control power is supplied internally from the main circuit DC power supply for all Drives. 3. Consult your Yaskawa representative before using 12-pulse rectification. Electrical Installation 2 - 9...
Page 11 (See Appendix E) may result in damage to the wiring, Drive and/or personal injury. 2. Control power is supplied internally from the main circuit DC power supply for all Drives. 3. Consult your Yaskawa representative before using 12-pulse rectification. Electrical Installation 2 - 10...
Page 12: Ground Wiring
Cable Length between Drive and Motor The E7 should be installed as close as possible to the motor to minimize the length of load side power cable needed between the Drive and the motor. If the cable between the Drive and the motor is long, the high-frequency leakage current will increase, causing the Drive output current to increase as well.
Page 13: Control Wiring
A2 signal employed is 4 to 20 mA with parameter H3-08 set for “2: 4 - 20 mA”. For 0 to 10 VDC, parameter H3-08 is set for “0: 0 - 10 VDC” and the E7 control board DIP switch S1-2 must be in the OFF position. (See Fig 2.4).
Page 14: Wiring Checks
Wiring Checks After all wiring is completed, perform the following checks: Is all wiring correct? Have all wire clippings, screws or other foreign material been removed from the Drive enclosure? Are all terminal screws tight? Electrical Installation 2 - 13...
Page 15: Control Circuit Terminal Functions
Control Circuit Terminal Functions The factory default functions of the control circuit terminals for 2-wire control are shown in Table 2.8. Table 2.8 Control Circuit Terminals Type Signal Name Description Signal Level Forward run/stop command Forward run when CLOSED; stopped when OPEN. Reverse run/stop command Reverse run when CLOSED;...
Page 16: Dip Switch S1
DIP Switch S1 DIP Switch S1 is described in this section. The functions of DIP switch S1 are shown in Table 2.9. Terminating resistance DIP Switch S1 located on terminal board. Fig 2.4 DIP Switch S1 Location Table 2.9 DIP Switch S1 Name Function Setting...
Page 17 Shunt Connector CN15 The shunt connector CN15 is described in this section. Shunt connector along with parameters H4-07 and H4-08 select the sig- nal range of the analog output terminals FM and AM. Shunt connector CN15 is only available when the optional Terminal Card with the 4-20mA Analog Output Monitor is installed (Model No.
Page 18 Sinking/Sourcing Mode The input terminal logic can be switched between sinking mode (0V common) and sourcing mode (+24V common) by using the terminals SN, SC, and SP. An external power supply can also be connected, providing more freedom in signal input methods.
Page 19: Terminal Connections
Terminal Connections Connections to Drive terminals are shown in Fig 2.6. Fig 2.6 Terminal Connections Electrical Installation 2 - 18...
Page 20: Control Circuit Wiring Precautions
Control Circuit Wiring Precautions Observe the following precautions when wiring control circuits: Separate control wiring from power/motor wiring (terminals R/L1, S/L2, T/L3, U/T1, V/T2, W/T3, 2, and 3) and other high-power lines. Separate wiring for control circuit terminals MA, MB, MC, M1, M2, M3, and M4 (digital outputs) from wiring to other control circuit terminals.
Page 21: Field Wiring Diagram
Field Wiring Diagram Use this diagram to document field wiring. It may be helpful to copy this page. Fig 2.8 Field Wiring Diagram Electrical Installation 2 - 20...

YASKAWA E7 Installation Manual

Table of Contents

Related Manuals for YASKAWA E7

Summary of Contents for YASKAWA E7

This manual is also suitable for:

Table of Contents