Table of Contents
Advertisement
Save ThisManual _X_
For Future Reference
SEARS
owner's
manuaa
MODEL NO,
113.235220
&
113=235240
COMPOUND
MITER SAW
MODEL NO.
113.235110
NON-COMPOUND
MITER
SAW
Serial
Number
Model
and serial number
may be found
on a plate
attached
to your saw, at
the side of the Miter Saw
arm.
You should record
both
model
and serial number
in
a safe place
for future use_
FOR YOUR
SAFETY:
10 iNCH MITER SAW
e assembly
• operating
o repair parts
READ ALL
INSTRUCTIONS
\
CAREFULLY J
Sears,Roebuck
and Co., Hoffman Estates, I L60179 U.S.A.
Part No. SP5990
Form NOr SP5990
J
Printed
in LISA 10/96
Advertisement
Table of Contents
Related Manuals for Craftsman 113.23522
Summary of Contents for Craftsman 113.23522
- Page 1 Save ThisManual _X_ For Future Reference SEARS owner's manuaa MODEL NO, 113.235220 & 113=235240 COMPOUND MITER SAW MODEL NO. 113.235110 NON-COMPOUND MITER Serial Number Model and serial number may be found on a plate attached to your saw, at the side of the Miter Saw arm.
-
Page 2: Warranty
FULL ONE YEAR WARRANTY within one year from the date of purchase, this Craftsman Miter Saw fails due to a defect in material or workmanship, Warranty service is available by simply contacting the nearest Sears service center/department throughout the United States. - Page 3 Z87 1 (shown on package) Everyday eyeglasses have blade for the only impact resistant lenses They are not safety glass- es Safety goggles are available at Sears retain stores Glasses or goggles not in compliance with ANSI Z87 1 push the could seriously hurt you when they break •...
- Page 4 • Do not use this saw to cut pieces too small to let you easily hold the work The thumb side of your index (pointer) finger should not be closer to the blade than...
-
Page 5: Glossary Of Woodworking Terms
Motor Specifications Power Supply and Motor Specifications The AC motor used in this saw is a universal, nonre- versible type having the following specifications: MODEL 113 235110... -
Page 6: Table Of Contents
Alignment ... Mounting the Miter Saw ... Safety Instructions for Basic Saw Operations ...14-!6 Basic Saw Operations ... Maintenance and Lubrication ... Sears Recommends the Following Accessories ... Trouble Shooting Guide ... Repair Parts ... (Continued) can occur if overload,... -
Page 7: Unpacking And Checking Contents
I WARNING: have to lift the saw more than 10 inches. during cord must 1 Remove the miter saw from the carton by lifting the saw by the carry handle. WARNING: do not plug damaged part is correctly... -
Page 8: Getting To Know Your Miter Saw
Getting to Know "YourMiter Saw Warning label 2,, Stop Shaft - The miter saw can be locked in the lowered position for compact storage. Miter Lock Knob - The miter lock knob securely locks the miter saw at a desired miter angle Index points have been provided at O, 22.5 R/L, and 45... -
Page 9: Assembly
4a. For Model 113 235220 & 113 235240 only, find the arbor lock between the upper guard and the miter saw handle press the arbor lock and hold it in firmly while turning the arbor screw The arbor lock will... -
Page 10: Alignment
Make sure the miter lock knob is loose but do not release the index spring. d. Use the miter saw knob to move the turn table and saw so that the blade contacts the full length of the square. Watch out for tooth seL Turn the... -
Page 11: Alignment
Bevel Pivot Adjustments 1, The miter saw should bevel easily by loosening the bevel lock knob and tilting the power head to the left If movement is tight or if there is looseness in the... - Page 12 The base of the saw has two sets of four holes to mount the miter saw, four smaller holes for "Drywall" screws and four larger holes for 5/16 bolts, (see illustration) If the saw is to be...
- Page 13 CATALOG NO 9-22244 LEG SET FRONT Mounting Board for Catalog No. 9-22244 Leg Set or NOTE: Attach the mounting board to the leg set first Then mount the saw to the mounting board using the °O I recommended hardware (not included) /"...
-
Page 14: Safety Instructions For Basic Saw Operations
Keep Guards in Place, in working order, and in proper adjustment. if any part of this miter saw is missing, bent, or broken in any way, or any electrical parts don't work, turn the saw off and unplug it. Replace damaged, missing, or failed parts before using the saw again. - Page 15 Z87.1 (shown on package). Everyday eyeglasses have only impact resistant lenses, They are not safety glass- es Safety goggles are available at Sears retail stores Glasses or goggles not in compliance with ANSI Z87l could seriously hurt you when they break •...
-
Page 16: Basic Saw Operations
A careless fraction enough to cause a severe injury. Before starting your cut, watch the miter saw while it runs. if it makes an unfamiliar noise or vibrates a lot, stop immediately. Turn the saw off, Unplug the saw, Do... - Page 17 Retighten miter lock knob Do not stand in front of the saw table Move with the handle to the miter angle to make the cut Bevel Cut Model 113.235220 &...
- Page 18 Basic Saw Operations Compound Model 113.235220 & 113,235240 Miter Saw Only: When a compound cut is required, select the correct bevel and miter Move your feet and body with pesitionr the handle to the desired miter angle to make the cut.
- Page 19 Correct any interference before proceed- ing. The auxiliary fence is used with the saw in the 0° bevel position If a bevel cut is desired, the auxiliary. fence will have to be removed...
- Page 20 A dimensional 4x4 may be cut with one cut by attaching an auxiliary fence of 7/8 thickness, with screws to the miter saw fence as shown on previous page,, Vertical Bevel Cutting To make a miter cut in a 2x4 workpiece (actual 1-5/8" x 3-1/2") in the vertical position (on edge) a spacer, such...
- Page 21 (Continued) Miters Tips For Cutting Model 113,235220 & 113.235240 Only: A compound miter saw is excellent for cutting crown molding. Crown molding is difficult to cut because in order to fit correctly it must be precisely mitered, All Standard (US) (fits next to ceiling) of 52 °...
-
Page 22: Maintenance And Lubrication
To inspect or reptace first unplug the saw Then remove the motor cap on the end of the motor by removing 2 screws. Remove the lead wires from the tabs on the brushes, then pull out the brushes To reassemble reverse the procedure. -
Page 23: Sears Recommends The Following Accessories
I WARNING: To avoid injury from unsafe acces- ommended accessories list in this manual. Prohibited Accessories The use of any cutting tool except 10" saw blades which meet the requirement under recommended accessories is prohibited, Do not use accessories such... -
Page 24: Trouble Shooting Guide
-15-Amp time delay fuse, or circuit breaker -See "Maintenance" section, -Authorized service -None SUGGESTED CORRECTIVE ACTION -Get authorized Sears Service, -See "Alignment" section., -Vacuum or blow out dust WEAR EYE PROTECTION -See "Alignment" section, -Get authorized Sears Service,,... - Page 25 WlDE BLADE ii [ lllllll[BW ' POWER CORD Trouble Shooting of brake by qualified ser- person only. vice I. Check commutation at no load. If there is a heavy sparking which follows the curvature of the commu- tator: replace the armature 2 To continue trouble shooting, now unplug the power cord 3.
-
Page 26: Repair Parts
Repair Parts ... PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO. 113.235220 & 113,235240 AND 113.235110 FIGURE MODEL113235220 & 1t 3 235240 ONLY... - Page 27 Repair Parts PARTS LIST FOR CRAFTSMAN MODEL NO. 113.235220 Always Part Description See Fig 4 Blade Guard Asm Motor Asm See Fig 2 823234 _Table 823230 I_1 Table (not shown) 823296 _Foot Locking 823313 Knob 823236 _kFence 823232 181 Fence (not shown) 823228 Base 823295...
- Page 28 _:CAUTION: See Mechanical Assembly Caution below. * WARNING: Any attempt to repair or replace electrical parts on this unit may create a Hazard unless repair is done by a qualified service technician° Repair service is available at your nearest Sears store. & 113.235240...
- Page 29 • WARNING: Uncontrolled spring release of mistnstallation of these parts may create a Hazard unless repair is done by a qualified service technician, Repair service is available at your nearest Sears store, WARNING: These items are important to the safety of this tool, Do not substitute common parts, 10"...
- Page 30 PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO. 113.235220 & 113.235240 AND 113.235110 FIGURE 4...
- Page 31 Screw Shoulder Bearing Cam ,& Model 113.235220 & 113.235240 Only I_ Model 1_3.235110 Only spring release or misinstallation Repair service is available at your nearest Sears store. AND 113.235110 of these parts may create a Hazard unless repair "O "13...
- Page 32 & 113235240 113,235110 10" NON-COMPOUND All parts listed may be ordered and most Sears stares, If the parts you need locally, your order wil! be electronically Repair Parts Distribution Center for handling, and Co., Hoffman Estates 60179 U.S.A. simply contact and Co.