Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson 201
Summary of Contents for Epson 201
- Page 1 Customer Display DM-D500 Installation Manual 401156101...
- Page 2 This document shall apply only to the product(s) identified herein. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
-
Page 3: Safety Precautions
This document presents important information intended to ensure safe and effective use of this product. Please read this document carefully, and store it in an accessible location near your installation. This document uses the two headings shown below to call attention to potential hazards. Failure to observe the information provided under or alongside these headings may lead to injury or property damage. -
Page 4: Emc And Safety Standards Applied
CAUTION: Do not plug the cable differently from the instruction in this manual. Wrong connection may cause equipment damage and fire. Be sure to set this equipment on a firm, stable, horizontal surface. Product may be damaged or cause injury if it falls. Do not use in locations subject to high humidity or dust levels. -
Page 5: About This Manual
You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment. FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 6: Table Of Contents
Precautions when connecting to a TM printer ....... . . -
Page 7: Unpacking
When connecting or disconnecting cables, make sure that the power switch of the DM-D500 and printers connected to the DM-500 are turned off. Do not drop the DM-D500, because you may damage the built-in vacuum fluorescent display. installation manual warranty card (201 model only) -
Page 8: Usage
Usage The DM-D500 can be used with the following equiment. IR Series. You can attach the DM-D500 to the IR Series using the “DM-D pole unit for IR” (DP-504). (See page 8.) TM-H5000II/TM-J8000 printers. You can attach the DM-D500 to TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)”... -
Page 9: Precautions When Connecting To A Tm Printer
B5X0 000001 and higher TM-T285 B5X0 510001 and higher TM-J8000 *1: If your printer is a TM-H5000, always purchase the latest model of the UB-S01 before using it with the DM-D500. If an old model of the UB-S01 (Part code: C8233610000)is connected to the TM printer, please purchase and install the latest model of the UB-S01 board (Part code: C8233610200). -
Page 10: Assembling
Assembling Attaching to the IR Series The DM-D500 can be attached directly to the IR Series using the “DM-D pole unit for IR” (DP-504). Required items The following items are used to attach the DM-D500 to the IR Series. These items are packed with the “DM-D pole unit for IR” (DP-504). fixing screws base Assembling steps... - Page 11 2. Attach the base to the setting position on the IR Series, and secure it with the screws. Note: When attaching the base, note that the corners of the base are set as shown below. 3. Pass the cable for the DM-D500 through the base. 4.
-
Page 12: Attaching To The Tm-H5000Ii/Tm-J8000
5. Connect the cable for the DM-D500 to the DM connector on the IR Series. Attaching to the TM-H5000II/TM-J8000 The DM-D500 can be attached directly to the TM-H5000II/TM-J8000 printers using the “DM-D pole unit for TM printers (Type B)” (DP-503). Required items The following items are used to attach the DM-D500 to the TM-H5000II/TM-J8000 printers. - Page 13 When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the base to the setting position on the TM printer and secure it with the screws.
- Page 14 3. Pass the cable for the DM-D500 through the base. 4. Insert the tab on the base into the hole on the support until you feel it click. 5. Connect the cable for the DM-D500 to the DM connector on the TM printer.
-
Page 15: Attaching To The Tm-U375/Tm-U950
Attaching to the TM-U375/TM-U950 The DM-D500 can be attached directly to the TM-U375/TM-U950 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). Required items The following items are used to attach the DM-D500 to the TM-U375/ TM-U950 printers. These items are packed with the “DM-D pole unit for TM printers (Type A)”... - Page 16 C to the DM-D500. When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the rubber feet to the printer. [TM-U375] When using support B...
- Page 17 4. Connect the cable for the DM-D500 to the DM connector on the TM printer. 5. Adjust the length of the cable and secure fixing plate A to the printer with screws. [TM-U375] [TM-U950]...
-
Page 18: Attaching To The Tm-H6000/Tm-U675
6. Store any excess cable in the support, and attach the DM-D500 to fixing plate A. Attaching to the TM-H6000/TM-U675 The DM-D500 can be attached directly to the TM-H6000/TM-U675 printers using the “DM-D pole unit for TM printers (Type A)” (DP-502). - Page 19 When using support B for extension, insert the tab on support B into the hole on support C until you feel it click. 2. Attach the rubber feet to the printer. 3. Attach fixing plate B to the printer. When using support B...
- Page 20 5. Connect the cable for the DM-D500 to the DM connector on the TM printer. 6. Attach fixing plate A to the TM printer using the stopper. When you attach the stopper, insert the projections on the stopper into the holes of fixing plate B.
- Page 21 7. The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw.
- Page 22 8. Store any excess cable in the support and attach the DM-D500 to fixing plate A. 9. Connect the power cable of the printer. To avoid disconnection, hook the cable to the tabs on fixing plate B, as shown below.
-
Page 23: Attaching To Other Tm Printers
Attaching to Other TM Printers When using with other TM printers, the DM-D500 can be attached to a desk or other surface, using the “DM-D pole unit for TM printers (Type A)” (DP-502), and Velcro tapes or screws. Required items The following items are used when the DM-D500 is used with other TM printers. - Page 24 3. Pass the cable for the DM-D500 through the hole on fixing plate A, and fix the cable at the bottom as shown below. 4. Connect the cable for the DM-D500 to the DC connector on the TM printer. When using support B for extension...
- Page 25 5. Store any excess cable in the support, and attach the DM-D500 to fixing plate A. 6. Peel off the Velcro tapes, and attach the display to the setting position. Assembling steps using screws 1. Follow steps 2 and 3 in “Assembling steps using Velcro tapes.” 2.
-
Page 26: Attaching To The Dm-D Stand
The DM-D500 can be attached directly to the DM-D stand using the “DM-D stand unit for DM-D 500” (DP-501). The DM-D500 with the DM-D stand can be connected to a TM printer, or be used as a stand alone product. - Page 27 (5mm). To distinguish the two types of screws, see the illustration below. notch (one or more lines) inch-type display connector millimeter-type printer connector extension cable connector RS-232C connector installation screw...
- Page 28 Set the jumpers on the DM-D stand as follows: Set the jumpers as in the left columns when connecting both the TM printer and the DM-D stand. (Default setting) Set the jumpers as in the left column when using the DM-D stand as stand alone.
- Page 29 Assembling steps 1. Pass the cable for the DM-D500 through the DM-D stand. When extending the length of the DM-D stand, attach the extension support (DP-105) to the DM-D stand. Insert the tab on the DM-D500 (or the extension support) into the hole on the DM-D stand until you feel it click.
- Page 30 5. When using as a stand alone, go to step 6. When using with the printer, connect one end of the printer interface cable for the printer to the printer connector on the DM-D stand; then connect the other end to the connector on the printer.
- Page 31 When using the extension cable, connect it (with the arrow mark up) to the extension cable connector indicated with “POWER OUT” on the DM-D stand; then connect the other end to the power connector on the printer. extension cable connector 7.
- Page 32 9. Arrange the cables as shown below. Put the cables for the DM-D500 inside the DM-D stand. 10. Attach the base plate to the DM-D stand following the number of the arrow shown below. At this time, push the base plate until it is locked by the hook on the DM-D stand.
-
Page 33: Part Names And Functions
Part Names and Functions Exterior display Display: Characters are displayed. Power switch: The power is turned on/off. DIP switch: The functions of the DM-D500 are changed. (See “DIP switch” for details.) Note: When turning on the DM-D500 again after turning it off, wait for at least 3 seconds. -
Page 34: Dip Switch
DIP Switch DIP Switch Functions The DM-D500 has two groups of DIP switches. The functions of the DIP switches are as follows: DIP switch 1 DSW1 No. Function Data receive error Hand shaking Data length Parity on or off Parity type Change transmis- sion speed (*1)XON/XOFF is effective only when the DM-D500 is connected with a stand alone. - Page 35 DM-D500 cannot be used, but when selecting “256 can be used. (*4)When setting to “Printer is selected,” data is sent to the TM printer, but is not displayed on the display. When setting to “Display is selected,” data is displayed on the display but is not output from the TM printer.
- Page 36 Setting the DIP switches CAUTION: Turn off the DM-D500 while removing the DIP switch cover to prevent electrical damage to the DM-D500. 1. Turn off the power for the DM-D500. 2. Remove the DIP switch cover. 3. Change each setting of the switches with a pointed object, such as a pen tip or small screwdriver.
-
Page 37: Turning And Tilting The Dm-D500
Turning and Tilting the DM-D5 0 0 You can turn or tilt the display while holding the support. The display can be moved easily, so do not move any further if it stops. If you move it by force, you may damage it. With the “DM-D pole unit for IR”... -
Page 38: Self Test
Self Test The DM-D500 has a self test function. If you want to perform a self test, you must change the setting of the DIP switch. Check Items of Self test The following items are checked during the self test: Control ROM version DIP switch settings Example of display characters... -
Page 39: Specification
Specification General Specifications Height, Width, Depth and Weight DM-D500 DM-D stand (DP-501) 200 mm • DM-D500: Height: Width: Depth: Weight: • DM-D stand (DP-501): Height: Width: Depth: Weight: <DM-D500 and DM-D stand> 213 mm 118 mm 83 mm 213 mm 51 mm 460 g 65 mm... - Page 40 (Type A)” (DP-502): Height: Width: Depth: Weight: <DM-D pole units> DM-D pole unit for DM-D pole unit for TM printers (Type A) TM printer (Type B) (DP-502) (DP-503) 248 mm 78 mm base 129 mm 50 mm 53 mm...
-
Page 41: Electrical Specifications
Tilt angle Horizontal rotation Vacuum fluorescent display • Total number of dots: • Dot pitch: • Number of characters: • Number of characters: • Display color: • Brightness: Electrical Specifications Type Rated voltage DC 11.4 to 48 V Rated current 0.53 A (at 11.4V) (max.) Environmental Specifications Operation environment Storage environment... -
Page 42: Character Specifications
Character Specifications Type of character • Alphanumeric characters: 95 • International characters: • Extended graphics: • Kanji characters (The Kanji character model supports printing with one of the following character sets.): Character grid • Font A: • Font B: • Kanji: Character style •...