Page 1
Use this service manual together with the KCH-14/15 service manual (B51-8728-00) or KCH-16 service manual (B51-8834-00). As for the hardware of this transceiver, version 3 is used. The programming software must use KPG-95DG. TK-5810(BG) with KCH-14 Metallic cabinet (Top) KCH-14 (A01-2161-32)
Neither is any liability assumed for dam- the fi rmware under the license of Digital Voice Systems, Inc. ages resulting from the use of the information contained herein. Kenwood reserves the right to make changes to any products herein at any time for improvement purposes. GENERAL...
3-1. Introduction Your KENWOOD dealer can help you select an antenna sys- Each radio is adjusted and tested before shipment. How- tem that will best serve your particular needs.
1. Install the front panel kit (controller) directly on a radio to Before Reading About System Set-up operate it. (Form: Radio + KCH-14/15) The TK-5810(BG)/5810H(BG) is a transceiver main unit 2. Remotely control one radio with one controller. (Form: (without a panel or speaker) that you complete by adding Radio + KRK-5 + KCH-14/15 + KCT-22M/M2/M3) options.
TK-5810 /5810H REALIGNMENT 1. Modes 2. How to Enter Each Mode Mode Operation User mode User mode Power ON Panel test mode [PF1] + Power ON Panel test mode Panel tuning mode PC mode Received commands from PC Data programming mode...
Page 6
TK-5810 /5810H REALIGNMENT 5-2. Connection procedure 6. PC Tuning Mode 1. Connect the transceiver to the computer using the inter- When making adjustment while in PC tuning mode, face cable and USB adapter (When the interface cable is modify the KPG-43/43A programming interface cable as de- KPG-43A, the KCT-53U can be used.).
Page 7
TK-5810 /5810H REALIGNMENT • KPG-43A • These transceivers use firmware versions G5.10 or Install the D-SUB socket into the cover after aligning the later. When using fi rmware versions earlier than version lead wire as shown in the fi gure.
Page 8
TK-5810 /5810H REALIGNMENT 7. The other target can be continuously cloned. When 11. Clone Mode the [PF2] key on the source is pressed while the source Programming data can be transferred from one trans- displays “END”, the source displays “CLONE MODE”.
Page 9
TK-5810 /5810H REALIGNMENT 12-1. Enter to the self programming mode 12. Self Programming Mode Press and hold the [GRP ] key while turning the trans- Write mode for frequency data and signaling etc. To be ceiver power ON. Ignoring whether the Read authorization used ONLY by the authorized service person maintaining the password is set or not, “PASSWORD”...
Page 10
TK-5810 /5810H REALIGNMENT 12-4. Key operation • Normal mode Zone- Channel Channel TX Mode RX NAC TX NAC Channel Frequency Frequency Type Spacing Signaling Signaling List No. [PF1] Unused [PF2] Go to the next item ANALOG/ Delete the least digit...
Page 11
TK-5810 /5810H REALIGNMENT 12-5. Self programming mode fl ow chart [GRP ] + Power ON Input Password Read authorization password entry (6 digits) [PF2] Self programming mode [PF2] [PF3] KEEP THIS CHANGE Zone/Channel Zone selection Channel selection [PF2] [PF2]: “YES” or [PF1]: “NO”...
TK-5810 /5810H INSTALLATION 1. Front Panel Kit (KCH-14/15: Option) 1-1. Installing the KCH-14/15 front panel kit to the transceiver 1. Remove the upper case and lower case of the transceiv- 2. Insert the lead wire with connector (W700) of the control unit (X53-440) into the connector (CN1) of the KCH-14 or KCH-15.
Page 13
TK-5810 /5810H INSTALLATION KCH-14 2. Remote kit (KRK-5: Option) The KRK-5 remote kit is used to remotely operate the POWER transceiver. The KRK-5 is connected to the KCH-14 or KCH- 15 with an optional KCT-22M (8 feet), KCT-22M2 (17 feet), or KCT-22M3 (25 feet) control cable.
Page 14
TK-5810 /5810H INSTALLATION 2-3. Control cable (KCT-22) connection (Fig. 2-3) 1. Insert one connector of the control cable to the trans- ceiver (with KRK-5) and the other to the display. Connect KRK-5 main panel the cable to the GND terminal with the screw q sup- plied with the control cable.
Page 15
TK-5810 /5810H INSTALLATION 3. Dual Control Head Remote Kit Transceiver (KRK-6DH: Option) The KRK-6DH remote kit connects two displays (two KCH-14s or KCH-15s) to the transceiver. The KRK-6DH is connected to the KCH-14s or KCH-15s with two optional CN503 control cables. There are three version of the control cable:...
Page 16
TK-5810 /5810H INSTALLATION Transceiver KRK-6DH main panel Cable fitting Display 2 Display 1 Cable fitting KCT-22 KCT-22 Control cable Control cable Fig. 3-2 4. Ignition Sense Cable (KCT-18: Option) 4-2. Connecting the KCT-18 cable to the KRK-5/6DH remote kit The KCT-18 is an optional cable to use the following func- 1.
Page 17
TK-5810 /5810H INSTALLATION 6-1. Connecting the KES-5 external speaker to the 5. Voice Guide & Storage Unit transceiver (VGS-1: Option) • When taking the AF output from the accessory con- nector (9-pin) on the rear of the transceiver 5-1. Installing the VGS-1 unit in the transceiver The following tools are required for changing the connec- 1.
Page 18
TK-5810 /5810H INSTALLATION 6-2. Connecting the KES-5 external speaker to the Note: KRK-5/6DH remote kit Even if the KRK-6DH is modifi ed in this way, the audio output of head 2 cannot be increased. • When taking the AF output from the 12-pin acces- sory connector on the rear of the control head •...
Page 19
TK-5810 /5810H INSTALLATION 7. Horn Alert Function 8. Handheld control head The HR1 and HR2 pins of the accessory connector (9- (KCH-16: Option) pin) on the rear of the transceiver are connected to the relay The KCH-16 Handheld control head is used to remotely (K500) and the maximum current is 1A.
/5810H DISASSEMBLY FOR REPAIR Note: Disassembly Procedure (TK-5810(BG)) When re-installing the fl at cable to the connector on the ■ Removing the upper/lower case and shielding cover CN600 side, do not align the cable as shown in the fi gure 1.
Page 21
TK-5810 /5810H DISASSEMBLY FOR REPAIR Note: Disassembly Procedure (TK-5810H(BG)) When re-installing the fl at cable to the connector on the ■ Removing the upper/lower case and shielding cover CN600 side, do not align the cable as shown in the fi gure 1.
Page 22
TK-5810 /5810H DISASSEMBLY FOR REPAIR Disassembly Procedure (TK-5810(BG)/5810H(BG)) Precautions for Reassembly ■ Removing the Control unit (X53-440) ■ Painting the lubricant (Part No.: 410-0019-05) on 1. Remove the 7 screws q. the groove of the case packing 2. Remove the shielding plate w.
Page 23
TK-5810 /5810H DISASSEMBLY FOR REPAIR ■ Align the cable connecting the W2 terminal: • Case packing (Lower) TK-5810H(BG) only TK-5810H When you assemble the fi nal unit, align the cable con- necting the W1 terminal as shown in fi gure, then insert it into the connector (CN1) of the control unit.
TK-5810 /5810H CIRCUIT DESCRIPTION 1. Overview 2. Frequency Confi guration This transceiver is a UHF/FM/P25 transceiver designed The receiver is a double-conversion superheterodyne to operate in the frequency range of 450 to 520MHz (K) or using fi rst intermediate frequency (IF) of 49.95MHz and sec- 400 to 470MHz (K2).
Page 25
TK-5810 /5810H CIRCUIT DESCRIPTION 3-3. 1st IF The 1st IF signal passing through these MCFs is ampli- fied by the IF amplifier (Q205) and goes into the FM IC The 1st IF signal passes through the MCF (Monolithic (IC209). Crystal Filter) to remove unwanted signal.
Page 26
TK-5810 /5810H CIRCUIT DESCRIPTION 3-6. Audio Amplifi er Circuit 3-7. Squelch Circuit Audio processing (high-pass filter, low-pass filter, de- It amplifies the demodulated noise signal from FM IC emphasized and so on) at FM mode and decoding at P25 (IC209) after fi ltering through BPF circuit. Then, the ampli- mode are processed by DSP.
Page 27
REFL (CN1) MODULE Fig. 9 Final amplifi er circuit: TK-5810(BG) Forward wave is detected by D2, and is converted into 4-5. Final Amplifi er Circuit (From Power module to DC voltage. The converted DC voltage is fed to the APC...
Page 28
(X400). Similarly, the VCO output signal is divided into comparative frequency by the programmable N divider 4-7. Temperature Protection Circuit: TK-5810(BG) in the PLL IC (IC400), and is compared with the divided ref- To prevent thermal destruction of the power module (IC2), erence signal in its phase detector.
Page 29
TK-5810 /5810H CIRCUIT DESCRIPTION The VCO oscillation frequency is determined by two sys- 5-4. Lockup Accelerator tems of operation switching terminals “STR” and “VCO1/2” The lockup accelerator is a circuit composed of a potenti- and two systems of voltage control terminals “C/V” and ometer IC (IC401) and a DC amplifi...
Page 30
TK-5810 /5810H CIRCUIT DESCRIPTION 6-4. Temperature Detection Circuit 6. Control Circuit The temperature detection circuit detects the tempera- The control circuit consists of the ASIC (IC708) and its ture using a temperature IC (IC702) and corrects the thermal peripheral circuits. IC708 performs the following;...
TK-5810 /5810H COMPONENTS DESCRIPTION Final unit (X45-3790-XX): TK-5810(BG) Ref. No. Part Name Description Ref. No. Part Name Description IC103 Buffer AMP (FTEMP1/FTEMP2) APC comparator IC200 Data multiplexer Power module IC201 Data multiplexer Diode ANT switch IC202~206 3.3V to 5V level converter...
Page 33
TK-5810 /5810H COMPONENTS DESCRIPTION Ref. No. Part Name Description Ref. No. Part Name Description IC700 Flash memory Diode DC/DC converter catch diode IC701 Digital signal processor Diode Logic control switch (SBC) IC702 Temperature sensor Diode DC/DC converter boost diode Reverse current prevention...
Page 34
TK-5810 /5810H COMPONENTS DESCRIPTION Ref. No. Part Name Description Ref. No. Part Name Description Q417 Transistor PLL f-in AMP Q200 Transistor RF AMP Q201,202 Transistor DC switch Q418 Transistor Buffer AMP Q203 Transistor Local AMP Q600,601 Transistor 8T switch Q204,205...
TK-5810 /5810H PARTS LIST CAPACITORS 2 2 0 • Capacitor value CC45 Color* 010 = 1pF 0 = 22pF 1 = Type ... ceramic, electrolytic, etc. 4 = Voltage rating 100 = 10pF 2 = Shape ... round, square, etc.
Page 36
Les articles non mentionnes dans le Parts No. ne sont pas fournis. C : China X : Australia M : Oth er Areas Teile ohne Parts No. werden nicht geliefert. TK-5810(BG)/5810H(BG) FINAL UNIT (X45-3790-XX): TK-5810(BG) Desti- Desti- Ref. No. Ad dress Parts No.
Page 37
TK-5810 /5810H PARTS LIST FINAL UNIT (X45-3790-XX): TK-5810(BG) FINAL UNIT (X45-3800-XX): TK-5810H(BG) Desti- Desti- Ref. No. Ad dress Parts No. Description Ref. No. Ad dress Parts No. Description parts nation parts nation CN1,2 E04-0154-05 PIN SOCKET S1R103J440H THERMISTOR E40-6429-05 FLAT CABLE CONNECTOR...
Page 38
AIR-CORE COIL R12-6431-05 TRIMMING POT .(220K/12) L34-4523-05 AIR-CORE COIL K : TK-5810(BG) K K2 : TK-5810(BG) K2 If a part reference number is listed in a shaded HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 box, that part does not come with the PCB.
Page 39
2.2UF C548 CC73HCH1H220J CHIP C 22PF K : TK-5810(BG) K K2 : TK-5810(BG) K2 If a part reference number is listed in a shaded HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 box, that part does not come with the PCB.
Page 40
CHIP C 0.10UF L703-707 L92-0162-05 BEADS CORE K : TK-5810(BG) K K2 : TK-5810(BG) K2 If a part reference number is listed in a shaded HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 box, that part does not come with the PCB.
Page 41
RK73HB1J101J CHIP R 1/16W R486,487 RK73HB1J101J CHIP R 1/16W R500 RK73HB1J393J CHIP R 1/16W R201 RK73HB1J103J CHIP R 1/16W R501 RK73HB1J153J CHIP R 1/16W K : TK-5810(BG) K K2 : TK-5810(BG) K2 HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2...
Page 42
1/16W R581 RK73HB1J472J CHIP R 4.7K 1/16W R716,717 RK73HB1J473J CHIP R 1/16W R583 RK73HB1J472J CHIP R 4.7K 1/16W R718 RK73HB1J474J CHIP R 470K 1/16W K : TK-5810(BG) K K2 : TK-5810(BG) K2 HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2...
Page 43
RV5C386A MOS-IC IC705 XC6109C29ANN ANALOGUE IC K : TK-5810(BG) K K2 : TK-5810(BG) K2 Note 1: This part cannot be replaced. Therefore, this part is not supplied as a service part. HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 If a part reference number is listed in a shaded box, that part does not come with the PCB.
Page 44
3.0PF K,HK C256 CC73GCH1H090B CHIP C 9.0PF K : TK-5810(BG) K K2 : TK-5810(BG) K2 Note 1: This part cannot be replaced. Therefore, HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 this part is not supplied as a service part.
Page 45
CC73GCH1H220J CHIP C 22PF C341 CK73GB1C104K CHIP C 0.10UF C466-468 CK73GB1E105K CHIP C 1.0UF C342 CK73GB1A224K CHIP C 0.22UF C470-472 CK73GB1H471K CHIP C 470PF K : TK-5810(BG) K K2 : TK-5810(BG) K2 HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2...
Page 46
470PF L220,221 L41-2278-08 SMALL FIXED INDUCTOR (22NH) K2,HK2 K : TK-5810(BG) K K2 : TK-5810(BG) K2 If a part reference number is listed in a shaded HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 box, that part does not come with the PCB.
Page 47
R276 RK73GB2A182J CHIP R 1.8K 1/10W K : TK-5810(BG) K K2 : TK-5810(BG) K2 If a part reference number is listed in a shaded HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2 box, that part does not come with the PCB.
Page 48
RK73GB2A392J CHIP R 3.9K 1/10W K2,HK2 R486 RN73GH1J151D CHIP R 1/16W K,HK R423 RK73GB2A103J CHIP R 1/10W K2,HK2 R486 RN73GH1J181D CHIP R 1/16W K2,HK2 K : TK-5810(BG) K K2 : TK-5810(BG) K2 HK : TK-5810H(BG) K HK2 : TK-5810H(BG) K2...
TK-5810 /5810H EXPLODED VIEW (TK-5810(BG)) 60x2 60x2 CN151 CN150 40x2 CN200 TX-RX unit XF201 XF200 CF203 CN10 Final unit Tighten the screw using a regulated torque. Please be careful not to tighten the screw so much that the terminal is warped.
Page 51
TK-5810 /5810H EXPLODED VIEW (TK-5810H(BG)) 60x3 60x3 34x2 40x2 C141 C139 C140 Final unit C143 CN150 C142 CN151 CN200 TX-RX unit XF201 XF200 CF203 KCH-14 CN502 KCH-15 K500 IC522 Control unit W700 : N09-2292-05 M3 x 8 (F) : N32-3008-43...
TK-5810 /5810H TROUBLE SHOOTING Fault diagnosis of the BGA (Ball Grid Array) IC ■ Overview A fl owchart for determining whether or not the transceiver can be powered on (the LCD does not function even if the power switch is turned on) due to broken BGA parts.
Page 55
An error occurs when the SRAM internal RAM The LCD displays “INIT ERROR3”. reads or writes. The SRAM may be broken. Replacing Control Unit ■ Control unit Information Original Control For Service Control Model Name unit Number unit Number TK-5810(BG) K,K2 X53-4400-10 X53-4400-11 TK-5810H(BG) K,K2...
TK-5810 /5810H ADJUSTMENT ■ Key operation Controls “FNC” not appears • KCH-14 (Basic control panel) Function Display Power switch Wide: “W” appears [Selector] Wide/Narrow/P25 Narrow: “N” appears POWER P25: “A” appears Shifts to the Panel tuning [GRP − mode TX BUSY High: “SP”...
Page 57
TK-5810 /5810H ADJUSTMENT • LED indicator • Test Signaling Red LED Lights during transmission. Signaling P25/ Green LED Lights when there is carrier. Analog None None Analog • LCD display in the panel test mode None 100Hz Square Wave Analog W : Wide QT 67.0Hz...
Page 58
TK-5810 /5810H ADJUSTMENT ■ 3, 5 or 7 reference level adjustments frequency Panel Tuning Mode • Assist voltage adjustments The transceiver is adjusted in this mode. TX assist voltage ■ Preparations for tuning the transceiver Tuning point Display Before attempting to tune the transceiver, connect the TX (MHz) unit to a suitable power supply.
Page 59
TK-5810 /5810H ADJUSTMENT ■ Adjustment item and Display (∗∗∗: 1~256) Adjustment item Display Wide/Narrow/P25 Tuning Point Note Transmit Assist Voltage VATX ∗∗ ∗ Receive Assist Voltage (Lower) VARXl ∗ ∗∗ Receive Assist Voltage (Upper) VARXu ∗∗ ∗ Frequency T XF ∗∗...
Page 60
TK-5810 /5810H ADJUSTMENT ■ Flow chart [PF1]: Not stored [PF5]: Stored Transmit Assist Voltage 7 reference level VATX adjustments [PF1]: Not stored [PF2]: Not stored [PF5]: Not stored Recive Assist Voltage 7 reference level VARXI adjustments [PF5]: Not stored Recive Assist Voltage...
Page 61
TK-5810 /5810H ADJUSTMENT BER (Bit Error Rate) Measurement [PF1]: Not stored 1. The Panel Test Mode is used to measure the BER (Refer 3 reference [GRP level to “Test mode operation features” described on page adjustments 56.). [PF1]: Not stored...
Page 62
Output Voltage 100mV or more 4Ω Dummy Load Approx. 4Ω, 30W 13.6V (TK-5810(BG)), 13.4V (TK-5810H(BG)) approx. 30A Regulated Power Supply (adjusted from 9 to 20V) Useful if ammeter equipped Caution Since the RX AF output is a BTL output, there is a DC Component.
Page 63
Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 1. Setting 1) DC voltage: 13.6V (TK-5810(BG)) 13.4V (TK-5810H(BG)) 2) SSG standard modulation [Wide] MOD: 1kHz, DEV: 3kHz [Narrow] MOD: 1kHz, DEV: 1.5kHz 2. Transmit 1) Adj item: [VATX]...
Page 64
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 4. MCF [Panel test mode] [PC test mode] Spectrum TX-RX CN202 TX-RX L218 Adjust the coils to obtain the waveform...
Page 65
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 8. Frequency 1) CH-Sig: 3-1 1) Channel: 3 f. counter Rear [Panel Change the adjust- adjust *1...
Page 66
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 5. Balance 1) Adj item: [BAL] 1) Adj item: [Balance] Deviation Rear [Panel Make the demodu- adjust *2 Adjust: [✳✳✳]...
Page 67
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 8. MIC sensi- 1) Adj item: [MIC] 1) Adj item: [Mic sen- Deviation Rear [Panel Adjust AG input 5.0mV±1.5mV...
Page 68
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 11. DTMF 1) Adj item: [DTMW] 1) Adj item: [DTMF Deviation Rear [Panel Write the value as ±100Hz...
Page 69
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment (Narrow) 1) Adj item: [MSKN] 1) Adj item: [MSK Deviation Rear [Panel Write the value as ±50Hz...
Page 70
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment 2. AF level [Panel test mode] [PC test mode] Rear Volume Turn the Volume 2.0V±0.3V knob...
Page 71
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment (P25) 1) Adj item: [SQOA] 1) Adj item: [Squelch Rear [Panel [Panel tuning mode] Adjust: [✳✳✳]...
Page 72
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment (P25) 1) Adj item: [RRSIA] 1) Adj item: [RSSI Rear [Panel [Panel tuning mode] Adjust: [✳✳✳]...
Page 73
TK-5810 /5810H ADJUSTMENT Condition Measurement Adjustment Specifi cations / Item Test- Remarks Panel tuning mode PC test mode Unit Terminal Unit Parts Method equipment (Narrow) 1) Adj item: [HRSIN] 1) Adj item: [RSSI Rear [Panel [Panel tuning mode] Adjust: [✳✳✳] (–70dBm) (Narrow)]...
Page 74
: –117dBm (0.32µV) 3) CH-Sig: 3-1 (MOD: 1kHz/±1.5kHz) 2) Channel: 2 3) Channel: 3 Adjustment Points CN10 CN151 CN150 CN200 FINAL UNIT (X45-3790-XX) : TK-5810(BG) Component side view CN14 L217 L222 L227 L229 TX-RX UNIT (X57-7270-XX) Component side view CN202 L218...
TK-5810 /5810H TERMINAL FUNCTION Final unit (X45-3790-XX): TK-5810(BG) Control unit (X53-4400-10) Pin No. Name Function Pin No. Name Function CN1 (to TX-RX unit CN151) CN1 (to Final unit CN13: TK-5820, W1: TK-5810H) TX drive input Power supply voltage CN2 (to TX-RX unit CN200)
Page 76
TK-5810 /5810H TERMINAL FUNCTION Pin No. Name Function Pin No. Name Function No connection No connection EMERGENCY signal output. No connection L: Operated, H: Not operated No connection L≤0.4V, H≥4.6V / 30kΩ load No connection No connection SCRAMBLE CONTROL signal output.
Page 77
TK-5810 /5810H TERMINAL FUNCTION Pin No. Name Function Pin No. Name Function MIC GND AUX I/O 6 I/O Auxiliary input/output 6 ASQL Analog squelch signal output No connection RSSI RSSI signal output No connection Tuning voltage signal input for RX BPF...
Page 78
Final unit temperature 2 CN150 Control voltage of VCO TX drive output CN151 (to Final unit CN1) CN601 (to Final unit CN9: TK-5810, CN2: TK-5810H) TX drive output TX power control voltage CN200 (to Final unit CN2: TK-5810, CN4: TK-5810H) RX signal input...
Page 79
Ignition sense input. AUX I/O 4 I/O Active low with 47kΩ pull up to 5V L≤0.8V, H≥4.2V Switched B (TK-5810(BG): 13.6V±15%/ TK-5810H(BG): 13.4V±15%) Auxiliary input/output 3 (FPU selectable) AUX I/O 3 I/O Active low with 47kΩ pull up to 5V L≤0.8V, H≥4.2V...
TK-5810 /5810H PC BOARD FINAL UNIT (X45-3790-XX): TK-5810(BG) -10 : K -11 : K2 Component side view (J79-0024-09) J79-0024-09 CN13 FINAL UNIT (X45-3790-XX): TK-5810(BG) -10 : K -11 : K2 Foil side view (J79-0024-09) J79-0024-09...
Page 81
TK-5810 /5810H PC BOARD FINAL UNIT (X45-3790-XX): TK-5810(BG) -10 : K -11 : K2 Component side view (J79-0024-09) CN10 Ref. No. Address Component side Layer 1 Layer 2 Layer 3 Layer 4 Foil side FINAL UNIT (X45-3790-XX): TK-5810(BG) -10 : K -11 : K2 Foil side view (J79-0024-09) Ref.
Page 97
TK-5810 /5810H SCHEMATIC DIAGRAM FINAL UNIT (X45-3790-XX): TK-5810(BG) ANT SW CN10 MA4PH633 MA4PH633 ANT SW R:0V T:1.53V ANT SW ANT SW R:13.60V CN14 T:12.60V E23-1290-05 SURGE ABSORPTION 13.6V PROTECT OF REVERSE CONNECTION CN13 E41-2672-05 X45-3790-XX 470p 470p • Note : The components marked with a dot ( ) are parts of layer 1.
Page 98
TK-5810 /5810H SCHEMATIC DIAGRAM FINAL UNIT (X45-3800-XX): TK-5810H(BG) R:13.4V R:13.4V T:12.72V T:12.73V R:0V R:0V T:2.38V T:2.11V TX DRIVE AMP FINAL AMP RD60HUF1-101 R:0V R:13.4V T:4.42V T:12.72V R:0V R:13.4V T:3.45V T:12.73V 470p FINAL AMP 470p RD60HUF1-101 FTEMP2 FTEMP1 R:0V R:0V DC AMP &...
Page 99
TK-5810 /5810H SCHEMATIC DIAGRAM FINAL UNIT (X45-3800-XX): TK-5810H(BG) FORWARD WAVE RECTIFICATION D5,6 ANT SW MA4P4002F MA4P4002F R:0V R:0V T:1.50V T:1.50V REFLECTED WAVE RECTIFICATION SURGE ABSORPTION R:0V T:4.76V R:0V T:5.78V R:0V R:0V T:0.81V T:0.41V 470p COMBINER MA2S111-F D7,8 D15,16 ANT SW ANT SW R:13.4V...
Page 107
TK-5810 /5810H SCHEMATIC DIAGRAM CONTROL UNIT (X53-4400-10) VREF VREF IC503 1kHz 1kHz L.P.F (RX) / R : 322mVrms R : 321mVrms BUFF AMP (SCR-RX) AF SWITCH 5.02V 2.00V C525 0.1u R : 0.01V IC506 SUMMING AMP (RX) / 5.02V TC7W53FK(F)
Page 108
TK-5810 /5810H SCHEMATIC DIAGRAM CONTROL UNIT (X53-4400-10) R : 2.00V T : 4.80V(KM) 4.90V(KH) T : 4.75V(K2M) 4.77V(K2H) VREF VREF 1kHz 2.00V R : 321mVrms 1kHz 1kHz R : 66mVrms R : 356mVrms 1kHz R : 322mVrms C575 AF AMP...
Dimensions (W x H x D) (Projections included) RF Deck only TRANSMITTER TK-5810 ..7.01 x 2.36 x 7.68 in. (178 x 60 x 195 mm) RF Output Power TK-5810H ..7.01 x 2.36 x 12.87 in. (178 x 60 x 327 mm) TK-5810 ............
Page 122
Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Bp 58416 Villepinte, 95944 Roissy Ch De Gaulle Cedex Kwai Fong, N.T., Hong Kong KENWOOD House, Dwight Road, Watford, Herts., 1 Ang Mo Kio Street 63, Singapore 569110 WD18 9EB United Kingdom...
Page 123
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD FINAL UNIT (X45-3790-XX): TK-5810(BG) FINAL UNIT (X45-3790-XX): TK-5810(BG) -10 : K -11 : K2 -10 : K -11 : K2 Component side view (J79-0024-09) Component side view (J79-0024-09) J79-0024-09 CN10 Ref. No. Address...
Page 124
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD FINAL UNIT (X45-3800-XX): TK-5810H(BG) FINAL UNIT (X45-3800-XX): TK-5810H(BG) -10 : K -11 : K2 Component side view (J79-0025-09) -10 : K -11 : K2 Component side view (J79-0025-09) C141 C122 C119 C116...
Page 125
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD FINAL UNIT (X45-3800-XX): TK-5810H(BG) FINAL UNIT (X45-3800-XX): TK-5810H(BG) -10 : K -11 : K2 Foil side view (J79-0025-09) -10 : K -11 : K2 Foil side view (J79-0025-09) J79-0025-09 Component side Layer 1...
Page 126
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD CONTROL UNIT (X53-4400-10) Component side view (J79-0234-19) CONTROL UNIT (X53-4400-10) Component side view (J79-0234-19) R403 R412 CN459 R420 IC400 R421 R422 R423 TXD3 R418 C471 /FLDM R707 F400 TP991 BLACK RXD2-GPS R346...
Page 127
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD CONTROL UNIT (X53-4400-10) Foil side view (J79-0234-19) CONTROL UNIT (X53-4400-10) Foil side view (J79-0234-19) R472 D411 R471 D412 R474 D423 R476 D422 C417 C415 C412 C413 R424 R461 D413 R425 IC401 Q403...
Page 128
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD TX-RX UNIT (X57-7270-XX) -10 : K -11 : K2 TX-RX UNIT (X57-7270-XX) -10 : K -11 : K2 Component side view (J79-0023-09) Component side view (J79-0023-09) CN151 CN150 CN601 C162 C212 C208...
Page 129
TK-5810 /5810H TK-5810 /5810H PC BOARD PC BOARD TX-RX UNIT (X57-7270-XX) -10 : K -11 : K2 TX-RX UNIT (X57-7270-XX) -10 : K -11 : K2 Foil side view (J79-0023-09) Foil side view (J79-0023-09) R162 R155 R165 R158 L444 C641...
Page 130
FINAL UNIT (X45-3790-XX): TK-5810(BG) POWER MODULE FORWARD WAVE RECTIFICATION HSM88AS-E ANT SW CN10 MA4PH633 E04-0154-05 100p MA4PH633 ANT SW R:0V T:1.53V R:0V R:13.60V R:4.40V T:3.79V T:12.40V HSM88AS-E REFLECTED WAVE RECTIFICATION ANT SW ANT SW E40-6429-05 FTEMP2 R:4.40V FTEMP1 330k MA2S111-F COMBINER R:13.60V...
Page 131
FINAL UNIT (X45-3800-XX): TK-5810H(BG) R:13.4V R:13.4V T:12.72V T:12.73V R:0V R:0V T:2.38V T:2.11V TX DRIVE AMP FORWARD WAVE FINAL AMP RECTIFICATION RD60HUF1-101 R:0V R:13.4V T:4.42V T:12.72V D5,6 ANT SW R:0V R:13.4V T:3.45V T:12.73V MA4P4002F 470p MA4P4002F FINAL AMP 470p RD60HUF1-101 R:0V R:0V T:1.50V T:1.50V...
Page 132
CONTROL UNIT (X53-4400-10) 13.6V:M DC/DC CONVERTER (5M) R : 2.00V L503 CN502 13.4V:H DBSW T : 4.80V(KM) 4.90V(KH) 13.6V:M 1.25V T : 4.75V(K2M) 4.77V(K2H) C609 C618 C630 13.4V:H LT1616ES6-PBF DC/DC BOOST R309 R305 /RF_SRoE 470p 1000p L504 SHDN +B_2 C207 0.1u C203 0.1u L505 5.05V...