Page 1
SERVICE MANUAL MODEL COMMANDER KV-HF21M80 RM-952 Vietnam SCC-U28EA-A DEST. CHASSIS NO. MODEL TRINITRON BG-3S CHASSIS COMMANDER DEST. CHASSIS NO. COLOR TV ®...
COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Page 3
(3) Schematic Diagram of C3 Board ... 54 (4) Schematic Diagram of F Board ... 57 5-5. Semiconductors ... 59 6. EXPLODED VIEW 6-1. Chassis ... 61 7. ELECTRICAL PARTS LIST – 3 – KV-HF21M80 RM-952 Title Page ... 63...
KV-HF21M80 RM-952 The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 5
Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp from flashing. 2 times 5 times Lamp OFF 3 sec. STANDBY/SLEEP lamp – 5 – KV-HF21M80 RM-952...
Page 6
KV-HF21M80 RM-952 SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [Screen display] / channel [5] / Sound volume [-] / Power ON...
Page 7
IC301. TV will stay on, but there will be no picture. * (Refers to the RGB levels of the AKB detection Ref pulse that detects IK.) IC301 IC001 SYSTEM IK-IN IO-8DAT O-LED PROTECT IO-SDAT – 7 – KV-HF21M80 RM-952 IC003 MEMORY B-DAT...
The operating instructions mentioned here are partial abstracts from the Operating Instruction Manual. The page numbers of the Operating Instruction Manual remain as in the manual. L(MONO) AUDIO VIDEO VIDEO IN VIDEO OUT...
Page 18
JUMP JUMP SOUND Á PROGR SOUND Á PROGR MODE MODE ONE-PUSH AUTOMATIC PROGRAMING FAVORITE FAVORITE ONE-PUSH AUTOMATIC PROGRAMMING...
Page 22
KV-HF21M80 RM-952 The following adjustments should be made when a complete realignment is required or a new picture tube is installed. These adjustments should be performed with rated power supply voltage unless otherwise noted. Controls and switches should be set as follows unless otherwise noted: PICTURE control ...
Page 23
V.STAT V. STAT H. STAT VR RV 702 BMC (Hexapole) Magnet. If the red, green and blue dots are not balanced or aligned, then use the BMC magnet to adjust in the manner described below. – 23 – KV-HF21M80 RM-952...
Page 24
KV-HF21M80 RM-952 Y separation axis correction magnet adjustment. 1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN] and [BRIGHTNESS] to [STANDARD] . 2. Adjust the Y separation axis correction magnet on the neck assembly so that the horizontal lines at the top and bottom of the screen are straight.
Page 25
3) BRIGHTNESS ... 50%. PICTURE ... MINIMUM 4) Select SBR (WHB7) with level with dimly lit. White – 25 – KV-HF21M80 175 V 2(VDC) for the best white balance. for the best white balance. [MUTING] then , and adjust SBR (WHB7)
KV-HF21M80 RM-952 4-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-952 that comes with this unit. a. ENTERING SERVICE MODE With the unit on standby [DISPLAY] VOL (+) [POWER] This operation sequence puts the unit into service mode.
Page 27
50Hz or 60Hz, be sure to use the respective input signal after adjustment. GREEN Adjusted with [3] and [6] buttons. GREEN The WRITE display then the display returns to a green SERVICE. – 27 – KV-HF21M80 [MUTING] , the data for all items are written into memory RM-952...
Page 31
ITEM INFORMATION. No. OPB0 OP1 Item XTAL 4.43 XTAL 3.58 KV-HF21M80 No. OPB1 OP2 NICAM Item KV-HF21M80 No. OPB2 OP3 Item Pic Rot KV-HF21M80 SECAM 2nd. Lang HDEV Thai Bil Dis. Fav 2199 Auto PIC Auto TV sys US ST –...
Page 32
When replacing IC003 (MEMORY), be sure to change IC001 ( - COM) to the following new IC at the same time. IC001( -CON):CXP86449-616S (KV-HF21M60/HF21P50) CXP86449-623S (KV-HF21M80) 1. Enter to Service Mode. 2. Press commander buttons 5 and - (Data Initialize), and 2 and - (Data Copy) to initialize the data.
Page 34
V2 L in VIDEO IN 2 *V2 R in (FRONT) V out 2 MONITOR L out 2 R out 2 – – KV-HF21M80 KV-HF21M80 RM-952 RM-952 COMB C in YC JUNGLE IC301 CXA2130S <slave:88H> 32 31 30 37 39 40...
Page 36
: MPP METALIZED POLYPROPYLENE : ALB BIPOLAR : ALT HIGH TEMPERATURE : ALR HIGH RIPPLE Note: The component identified by shading and mark ! are critical for safety. Replace only with part number specified. digital multimeter. – 43 – KV-HF21M80 RM-952...
Page 50
METAL OXIDE 1/10W R647 1-249-401-11 CARBON 1/10W 1/4W F R648 1-216-057-00 RES,CHIP 1/10W R649 1-249-417-11 CARBON 1/4W – 69 – KV-HF21M80 RM-952 REMARK 1/10W 100K 1/10W 100K 0.50% 1/10W 3.3K 0.50% 1/10W 1/4W F 1/4W 0.47 1/2W F 0.47 1/2W F 0.47...
Page 51
– 70 – The components identified by shading and mark ! are critical for safety. Replace only with part number specified. DESCRIPTION REMARK <TUNER> TUNER, FSS BTF-LG433 (KV-HF21M80) <CRYSTAL> VIBRATOR, CERAMIC VIBRATOR, CRYSTAL VIBRATOR, CRYSTAL ******************** SCREW +PSW 3X8 <CAPACITOR>...
Page 55
DESCRIPTION 9-965-767-01 REMARK REF. NO. PART NO. Sony Corporation Sony Technology Malaysia Sdn. Bhd. TV Business of General Area – 74 – The components identified by shading and mark ! are critical for safety. Replace only with part number specified.