YES CHEF LABEL Alpha-3R User Manual

Direct thermal portable printer

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

DIRECT THERMAL PORTABLE PRINTER

For YES CHEF LABEL Android Application

User's Manual

The copyright in this manual, the software and firmware in the printer described

CG Triumvirate is a trademark of Agfa Corporation. CG Triumvirate Bold

Condensed font is under license from the Monotype Corporation. Windows is a

registered trademark of Microsoft Corporation.

All other trademarks are the property of their respective owners.

Information in this document is subject to change without notice and does not

represent a commitment on the part of TSC Auto ID Technology Co.

No part of this manual may be reproduced or transmitted in any form or by any

means, for any purpose other than the purchaser's personal use, without the

expressed written permission of TSC Auto ID Technology Co.

This document is a manual how to start the printer. This document Is not recommended to use for repair

or hardware / software upgrade. If you have any technical questions regarding the printer installation and

configurations please send us an email to procurement@yescheflabel.com

Table of Contents

Summary of Contents for YES CHEF LABEL Alpha-3R

Page 1 DIRECT THERMAL PORTABLE PRINTER For YES CHEF LABEL Android Application User’s Manual Copyright Information © 2012 TSC Auto ID Technology Co., Ltd, The copyright in this manual, the software and firmware in the printer described therein are owned by TSC A uto ID Technology Co., Ltd, All rights reserved.
Page 2 Agency Compliance and Approvals 2014/30/EU(EMC), 2014/35/EU(LVD), 2011/65/EU(RoHS 2.0) EN 55032 Class B EN 55024 EN61000-3-2:2014 EN61000-3-3:2013 EN 60950-1 FCC part 15B, Class B This equipment has been tested and found to comply with the limits for a Class B digit al device, pursuant to part 15 of the FCC Rules.
Page 3 10 C.F.R. Section 430.23(aa) (Appendix Y to Subpart B of part 430) TP TC 004/2011 TP TC 020/2011 LP0002 KN 32/35 IS 13252(Part 1)/ IEC 60950-1 This document is a manual how to start the printer. This document Is not recommended to use for repair or hardware / software upgrade.
Page 4: Important Safety Instructions
Important safety instructions: 1. Read all of these instructions and keep them for later use. 2. Follow all w arnings and instructions on the product. 3. Disconnect the pow er plug from the AC outlet before cleaning or if fault happened. Do not use liquid or aerosol cleaners.
Page 5 2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40) 5GHz: 802.11a, The frequency, mode and the maximum transmitted pow er in EU are listed below: 2400 MHz – 2483.5 MHz: 19.88 dBm (EI RP) 5150 MHz – 5250 MHz: 17.51 dBm (EI RP) 5150-5350MHz for Only indoor use 5470-5725MHz for indoor/outdoor use Restrictions In AZE Azerbaijan...
Page 6 d'exposition aux fréquences radio de l'I ndustry Canada (I C). Utilisez l’appareil sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a été év alué et démontré conforme aux limites SAR (Specific Absorption Rate – Taux d'absorption spécifique) par l'I C lorsqu'il est connecté à des dispositifs hôtes spécifiques opérant dans des conditions d’utilisation mobile.
Page 7: General Specifications
Our Alpha-3R is designed for a rough life, inside the IP54-rated protective case to resist dust and water and with its rubber over-mold design prepared to take up to a five foot fall and keep printing.
Page 8: Unpacking And Inspection
Printout bias Vertical: 1 mm max. Horizontal: 1 mm max. Media Specifications Alpha-3R Media roll capacity 57 mm (2.25”) OD Label: 55 mm (2.16”) OD Media type Selected label Media wound type Printing face outside wound Media widt h Label: 2” ~ 3.07”...
Page 9: Battery Safety Warning
On the back side of the printer is located the battery place. Install the battery. Use the clip as shown in the photo to remove the battery. Battery safety warning: DO NOT throw the battery in fire. DO NOT short circuit the contacts. DO NOT disassemble the battery.
Page 10 Note: Please switch OFF printer power prior to plug in the power cord to printer power jack. When the battery is charging, please do not remove the battery from the printer, otherwise, please re-plug the power cord into a power outlet. Charger works in 220/240 Volts sockets When the battery is charging, the colour of battery status LED indicator is solid amber.
Page 11 On the right side of the printer use a screw or a coin to turn the correct positioning for the labels Make sure you insert the labels correct side. You should be facing the label. This document is a manual how to start the printer. This document Is not recommended to use for repair or hardware / software upgrade.
Page 12 Insert the Belt Clip as shown in the photo below. Click on the power button once the printer is fully charged. Recommend to charge the printer for 6 hours before first use. This document is a manual how to start the printer. This document Is not recommended to use for repair or hardware / software upgrade.
Page 13: Printer Overview
Printer Overview 1. LED indicator 2. Feed button 3. Power on/off button 4. Media cover release button 5. Media holder adjustment knob 6. Media cover 1. Tear edge 2. Print head This document is a manual how to start the printer. This document Is not recommended to use for repair or hardware / software upgrade.
Page 14 3. Media holder 4. Platen 5. Gap sensor 1. Li-ion battery 2. Battery open clasp 3. USB interface 4. Power jack 5. Interface cover 1. Power on/off button 2. Printer status LED indicator This document is a manual how to start the printer. This document Is not recommended to use for repair or hardware / software upgrade.
Page 15: Connecting With Bluetooth
3. Battery charge level LED indicator 4. Battery status LED indicator 5. Wireless status LED indicator 6. Feed button 1. Press and hold for 2-3 seconds to turn on the printer. 2. Press and hold for 2-3 seconds to turn off the printer. 1.
Page 16: Troubleshooting
Troubleshooting The follow ing guide lists the most common problems that may be encountered w hen operating this printer. I f the printer still does not function after all suggested solutions have been inv oked, please contact the Customer Service Department at procurement@yescheflabel.com * The battery is not properly * Reinstall the battery.
Page 17: Maintenance
Maintenance This session presents the clean tools and methods to maintain your printer. Please use one of follow ing material to clean the printer. Cotton sw ab Lint-free cloth Vacuum / Blow er brush 100% Ethanol or I sopropyl Alcohol Note: Do not touch printer head by hand.