Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1
GEnErAL SAFETY
WARNING! Ensure Health & Safety, and local authority
regulations are adhered to when assembling and using these
shelves.
Locate shelves in a suitable area where they will not be an
obstruction.
Keep the general area clean, uncluttered and ensure there is
adequate lighting.
WARNING! Erect shelves on a level and solid surface such as
concrete.
Keep children and unauthorised persons away from the storage
area.
DO NOT use the shelves for any purpose other than that for
which they are designed.
DO NOT site the shelves out of doors.
DO NOT get the shelves wet or use in damp or wet locations or
areas where there is condensation.
DO NOT clean the shelf suports with any solvents which may
damage the coated surface.
Ensure that the shelves are properly assembled before loading
them with heavy items.
Where possible the unit should be fixed to the wall with
suitable fixings
Place heavier items on the lower shelves.
Where possible heavier items should be evenly distributed across
the shelves.
2. INTRODUCTION
Fully painted steel frame with five MDF shelves. 500kg Capacity per
level giving a maximum capacity of 2500kg per rack. no nuts and
bolts means no tools required to assemble. Clips together in minutes.
racking can be used as a single bay rack (Fig.1) or split into two
separate shelf systems or workstations (Fig.2).
AP6500. . . Height: 1800mm . . . Width: 900mm . . . . Depth: 450mm
Fig.1
InSTruCTIonS For:
RACKING UNIT WITH 5 SHELVES
AP6500
MoDEL no's:
3. CONTENTS
3.1
Carefully unpack the product and check the contents as
detailed in Fig.3. Should any items be missing or damaged
contact your Sealey dealer.
4. ASSEMbLY
4.1
We recommend that this shelving unit be assembled by two
people. A rubber mallet or a hammer and a piece of wood
can be used to aid assembly.
Do not use a hard faced hammer directly on the beams as
this will damage their surface finish. Make sure that the shelf
support tabs are in line with the leg angle slots. If the tabs
and slots are not lining up do not use force as this may
damage the tabs. If the tabs are out of line bend them slightly
to line up with the slots.
Fig.2
Fig.3
AP6500 Issue: 1 - 05/06/09
Advertisement
Related Manuals for Sealey AP6500
Summary of Contents for Sealey AP6500
- Page 1 AP6500 MoDEL no's: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 (C). Tap the beam at either end to ensure that the tabs are properly seated in the slots. Make up a second upper end frame using the remaining two angle posts and a short step beam. Fig.6 AP6500 Issue: 1 - 05/06/09...
- Page 3 Ensure that the beams are the right way up. Tap the beams at either end to ensure that the tabs are properly seated into the slots. Fig.10 AP6500 Issue: 1 - 05/06/09...
- Page 4 Fig.15 4.14 See Fig.16. Place the two units end to end as shown below . Fig.13 Fig.16 Sole UK Distributor 01284 757500 www.sealey.co.uk Sealey Group, 01284 703534 sales@sealey.co.uk Bury St. Edmunds, Suffolk. email AP6500 Issue: 1 - 05/06/09...