Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
Please register your product with Sealey by completing the registration form on-line at
Navigate to Register Product. By registering your product you can take advantage of Sealey product and technical
updates via email.
1. SAFETY INSTRUCTIONS
WARNING! Ensure that Health and Safety, local authority and general workshop practice regulations are
strictly adhered to.
DO NOT use the unit if it, or any attachment, is damaged.
Maintain tester in good and clean condition for best and safest performance.
If required, ensure that the vehicle to be worked on is adequately supported with axle stands or ramps and is
chocked.
Put transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure
the parking brake is engaged.
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging. Do not wear jewellery and tie back long hair.
WARNING! Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark
plugs. These components create hazardous voltages when the engine is running.
DO NOT connect or disconnect any test equipment with ignition on or engine running.
Keep a fire extinguisher nearby, which is suitable for gasoline/chemical/electrical fires.
Account for all tools and parts being used and do not leave any in the engine bay.
Keep reset tool dry, clean and free from oil, water and grease. Use a mild detergent on a clean cloth to clean
the outside of the tool.
Operate the vehicle in a well-ventilated work area; exhaust gases are poisonous.
IMPORTANT: Always refer to the vehicle manufacturer's service instructions to establish the current procedure
and data. These instructions are provided as a guide only.
WARNING! The warnings and instructions discussed in this manual cannot cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are factors which
cannot be built into this product, but must be applied by the operator.
When not in use, store tester away in its box, in a cool, dry, childproof location.
2. INTRODUCTION
Designed for resetting Electronic Parking Brake (EPB) and extinguishing the
service interval lights, including the service interval messages, that are
displayed in the Driver Information Module after carrying out routine
maintenance on Volvo vehicles. Simple push button application. Powered by
connection to the vehicle.
INSTRUCTIONS FOR:
SERVICE LIGHT & EPB RESET TOOL
- VOLVO
MODEL No: VS8625
TECHNICAL HELP LINE No. 01284 757505
Original Language Version
www.sealey.co.uk
VS8625 Issue: 1 - 21/07/10
Advertisement
Related Manuals for Sealey VS8625
Summary of Contents for Sealey VS8625
- Page 1 - VOLVO MODEL No: VS8625 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 • enables service and repair functions to be carried out on EPB systems. The new VS8625 Volvo SLR and EPB tool has been designed to allow users to extinguish the service light following the servicing of a vehicle. It also allows for the servicing and replacement of brake pads and components used in the new Electronic Parking Brake systems which have been introduced to the Volvo range.
- Page 3 3.4.3. Ensure the park brake is released. 3.4.4. Press the OK button and the pistons can be heard retracting ( The Mode LED will flash during this process). 3.4.5. Once the process is complete, the EPB LED will flash. NOTE: Wait until the EPB LED flashes and the callipers have stopped moving before carrying out any work on the braking system. EPB Open Original Language Version VS8625 Issue: 1 - 21/07/10...
- Page 4 (The function LED will flash during this process). 3.5.4. Once the process is complete, the EPB LED will flash. NOTE: Any codes that are not able to be cleared will remain on the Module. Use the Sealey VST Electronic Auto Service and Diagnostic tool to determine what these codes are and what EPB Close steps need to be taken to resolve the problem.