Related Manuals for Toro 22414
Summary of Contents for Toro 22414
- Page 1 Form No. 3430-870 Rev A 48in Hydraulic Blade Compact Tool Carriers Model No. 22414—Serial No. 404000000 and Up *3430-870* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 Figure 1 Introduction The hydraulic blade is intended to be used on a Model No. Toro compact tool carrier. The blade is designed to hydraulically change its angle as needed for earth Serial No. and snow grading applications. Using this product for purposes other than its intended use could prove dangerous to you and bystanders.
-
Page 3: Table Of Contents
Contents Safety Safety ............... 3 DANGER General Safety ........... 3 Slope Safety ............4 There may be buried utility lines in the work Hydraulic Blade Safety ........4 area. Digging into them may cause a shock Maintenance and Storage Safety......4 or an explosion. -
Page 4: Slope Safety
Slope Safety Hydraulic Blade Safety • Operate the machine up and down slopes with • For wheeled traction units with a built-in operator's the heavy end of the machine uphill. Weight platform, do not use the counterweight on the distribution changes with attachments. This traction unit when using the attachment. -
Page 5: Safety And Instructional Decals
Weight 96 kg (212 lb) To ensure optimum performance and continued safety certification of the machine, use only genuine Toro replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous, and such use could void the... -
Page 6: Operation
Operation CAUTION Hydraulic couplers, hydraulic lines/valves, Determine the left and right sides of the machine from and hydraulic fluid may be hot. If you contact the normal operating position. hot components, you may be burned. • Wear gloves when disconnecting the Installing and Removing hydraulic couplers. -
Page 7: Operating Tips
Operating Tips • Clean the area of trash, branches and rocks before beginning work to prevent equipment damage. • Always begin with the slowest ground speed possible. Increase speed if conditions permit. • Always use full throttle (maximum engine speed). •... -
Page 8: Maintenance
Maintenance Determine the left and right sides of the machine from the normal operating position. CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure... -
Page 9: Storage
Storage Before long term storage, wash the attachment with mild detergent and water to remove dirt and grime. Check the condition of the cutting edge. Remove and rotate the blade 180 degrees so the worn edge is on top, if it is badly worn. Check and tighten all bolts, nuts, and screws. -
Page 10: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The blade does not change angle. 1. A hydraulic coupler is not completely 1. Check and tighten all couplers. connected. 2. A hydraulic coupler is damaged. 2. Check the couplers and replace any that are damaged. 3. - Page 11 Notes:...
- Page 12 Notes:...
- Page 13 Notes:...
- Page 14 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 15 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 16 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.