Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEaSE rEad tHESE inStructionS carEFuLLY. notE tHE SaFE oPErationaL rEQuirEMEntS, WarninGS & cautionS.
uSE tHE Product corrEctLY and WitH carE For tHE PurPoSE For WHicH it iS intEndEd. FaiLurE to do So MaY cauSE
daMaGE and/or PErSonaL inJurY and WiLL inVaLidatE tHE WarrantY. PLEaSE KEEP inStructionS SaFE For FuturE uSE.
1. SaFEtY inStructionS
WarninG! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
Use a qualified person to lubricate and maintain the tilt. do not use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the tilt clean for best and safest performance.
Locate the tilt in a suitable work area. Keep area clean and tidy and free from unrelated materials, and ensure that there is adequate lighting.
WarninG! Use the tilt on level and solid ground, preferably concrete. Avoid tarmacadam since the tilt may sink into the surface.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
Keep children and non-essential persons away from the work area.
do not exceed the rated capacity, which is 400kg. Ensure the load is evenly distributed on the tilting frame and secured if necessary.
Before lifting check that there are no overhead obstructions.
When work is complete, check under the tilting frame to ensure that there are no obstructions and that it is safe to lower the unit.
do not operate the tilt if any parts are damaged or missing as this may cause failure and/or possible personal injury.
do not place any part of your body within or under the tilt during use.
do not operate the tilt when you are tired or under the influence of alcohol, drugs or intoxicating medication.
do not use the tilt for any purpose other than that for which it is designed.
do not make any alterations or modifications to this product.
do not allow untrained persons to operate the tilt.
do not move or dolly the vehicle whilst on the tilt.
do not expose the tilt to excessive moisture or allow it to get wet.
Immediately after lifting, support the load with the safety support rod and ensure that the safety bar is fully engaged.
Lift only by positioning the wheels of the vehicle within the tilting frame.
Take great care when placing yourself under or in a position close to the load and if possible do not work directly underneath it.
notE: The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may
occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied
by the operator.
Store tilt in a dry, safe, childproof environment when not in use.
2. introduction and SPEciFication
2.1.
introduction
Heavy-duty all steel construction tilt lift, suitable for use with ride-on lawn mowers and quad bikes. Provides side access to vehicle
ideal for cleaning and maintenance work. Fitted with foot operated hydraulic pump unit and mechanical locking mechanism
preventing accidental lowering. Features three lockable tilting angles and stabilising bar. Fitted with carry handle and two fixed
wheels for easy manoeuvrability when not in use.
2.2.
Specification
Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . . 400kg
Locking Positions: . . . . . . . . . . . . . . .350mm/25°
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .695mm/40°
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .990mm/60°
Width:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 430mm
Length: . . . . . . . . . . . . . . . . . . . . . . . . . . 1800mm
3. oPEratinG inStructionS
3.1.
Before first use.
3.1.1.
Inspect the tilt carefully before each use. Make sure that it is not damaged, badly worn, or that any parts are missing.
3.1.2.
Do not use the jack unless it is in a good clean condition.
3.1.3.
During shipment and handling, air can become trapped in the hydraulic system causing the jack to malfunction. To release any air
from the hydraulic system, complete the following:
3.1.4.
Turn the release valve counter-clockwise, no more than two full turns.
3.1.5.
Slightly loosen the oil filler plug on top of the hydraulic unit.
3.1.6.
Pump the jack pedal quickly, for several full strokes.
3.1.7.
Re-tighten the oil filler plug, and close the release valve by turning it clockwise.
3.2.
To raise a load.
3.2.1.
Position the tilt in a suitable work location and on stable, level ground.
3.2.2.
Pull out the supporting frame from the stand (fig.2).
3.2.3.
Ensure that the area is secure, by keeping other people, children and animals at a safe distance.
3.2.4.
Position the vehicle's wheels over the lifting cradle, by manually manoeuvring it into position (fig.3).
If the vehicle has a parking brake, apply it.
3.2.5.
Locate the foot pedal into its fitting, and pump the foot pedal to raise the tilting frame.
3.2.6.
Continue to pump the foot pedal, the safety device should activate in the locking positions as the tilting frame rises.
3.2.7.
It is advisable to place a safety strap (not included) around the wheel(s) and the lifting cradle.
3.2.8.
If required, continue the lifting operation until the safety device activates at the highest locking position (fig.4).
3.2.9.
When raised to its full height, place the safety support rod between the lifting cradle and the base frame (fig.5), two people may
be required for this operation as the tilting frame will need to be lowered onto the safety support rod whilst it is held in place.
For maximum safety, it is advisable to tilt the vehicle to the maximum height, so that the safety support rod can be employed.
INSTRUCTIONS FOR:
Mini tractor/Quad BiKE tiLt
MODEL No:
Original Language Version
Mtt400
MTT400
Issue: 1 - 02/11/11
Advertisement
Related Manuals for Sealey MTT400
Summary of Contents for Sealey MTT400
- Page 1 WarninG! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment. Use a qualified person to lubricate and maintain the tilt. do not use brake fluid to top up hydraulic unit. Use Sealey hydraulic oil only.
- Page 2 Periodically check the hydraulic oil level by removing the rubber plug on the pump, add hydraulic oil as required. WarninG! Only a good quality hydraulic oil, such as SEaLEY HYdrauLic JacK oiL, must be used. do not use brake ...
- Page 3 For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, 01284 703534 sales@sealey.co.uk IP32 7AR email Original Language Version MTT400 Issue: 1 - 02/11/11...