Related Manuals for Fujitsu PA03740-K010
Summary of Contents for Fujitsu PA03740-K010
- Page 1 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS FI-7600/FI-7700 CONSUMABLE REPLACEMENT AND CLEANING INSTRUCTIONS ...
-
Page 2: Consumables And Replacement Cycles
HINT Only use the specified consumables. To purchase the consumables, contact your FUJITSU scanner dealer or an authorized FUJITSU scanner service provider. CG00002 ‐ 296501 ... - Page 3 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Replacing the Brake Roller Replace the Brake Roller in the following . Remove the brake roller procedure. Lift the left side of the roller in the Turn off the scanner and wait for at least direction of the arrow 1 first, then pull 15 minutes. out the shaft from the slot on the right Unplug the power cable in the direction of the arrow 2 Remove all documents from the ADF paper chute (feeder) Open the ADF cover . Remove the brake roller from its shaft . CG00002 ‐ 296501 ...
- Page 4 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Attach a new brake roller on the shaft. Insert the protrusion on the shaft into the slot. . Attach the shaft. Insert the right end of the shaft into the hole in accordance with the hole shape in the direction of the arrow 1, and then attach the left side of the shaft in the direction of the arrow 2. CG00002 ‐ 296501 ...
- Page 5 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Close the cover . Close the ADF. . Plug in the power cable and turn on the scanner. . Reset the brake roller counter Reset the brake roller counter by performing one of the following actions: Reset the counter in [4: Consumable Counters] on the [Settings Menu] screen of the Operator Panel. Reset the counter in the Software Operation Panel.* *For details, refer to the Operators Guide CG00002 ‐ 296501 ...
-
Page 6: Replacing The Pick Roller
FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Replacing the Pick Roller Replace the Pick Roller in the following . Open the sheet guide. procedure. Slide the side guides all the way out by pressing the side guide buttons, and pull the sheet guide open from the dip. Turn off the scanner and wait for at least 15 minutes. Unplug the power cable. Remove all documents from the ADF paper chute (feeder) Open the ADF CG00002 ‐ 296501 ... - Page 7 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Remove the pick roller closer to you. c. Remove the pick roller. a. Rotate the bushing (x2) on the shaft in the direction of the arrow. . Remove the shaft of the pick roller away from you. b. Slide the bushing (x2) on the shaft in the direction of the arrow. a. Rotate the bushing on the shaft in the direction of the arrow. CG00002 ‐ 296501 ...
- Page 8 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS b. Lift up the bushing in direction 1 (about 5mm), and slide the shaft in direction 2 to pull out the leading end from the slot, then lift the shaft in direction 3 to remove it. . Remove the pick rollers (x2) from the shaft one at a time. a. Pull out the pick roller from the shaft as you lift the retaining clip. b. Pull out the other pick roller from the shaft as you lift the retaining clip. CG00002 ‐ 296501 ...
- Page 9 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Attach new pick rollers (x2) on the shaft, . Install the shaft of the pick roller in the one at a time. side away from you. The Software Operation Panel is installed together with the PaperStream IP driver. a. Hold the bushing of the shaft in one hand a. Insert the left end of the shaft into the This application allows you to configure various settings such as the operation of the scanner and the pick roller with the retaining clip slot, and lower the other end gradually. and management of the consumables. facing toward you in the other hand, and then put the pick roller on the shaft in the direction of the arrow 1 . If you rotate the pick roller in the direction of the arrow 2 , you can put it on the shaft more easily. 1. Confirm that the scanner is connected to the computer, then turn on the scanner. 2. Display the [Software Operation Panel] Window b. Rotate the bushing on the shaft in the b. Hold the bushing of the shaft in one hand *Windows Vista/Windows 7/Windows Server 2008 direction of the arrow. and the other pick roller with the retaining Click [Start] menu [All Programs] [SP Series] [Software Operation Panel]. clip facing towards you in the other hand, ...
- Page 10 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS c. Fit the protrusion on the right shaft into . Install the new pick roller in the side the notch on the pick roller and slide the closer to you. bushing on the right shaft in the direction of a. Insert the protrusion (x2) on the the arrow. scanner into the hole (x2) on the pick roller. d. Rotate the bushing (x2) on the shaft in the b. Slide the bushing on the left shaft in the direction of the arrow. direction of the arrow. CG00002 ‐ 296501 ...
- Page 11 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Close the sheet guide. Make sure that both ends of the sheet guide are locked firmly. . Close the ADF. . Plug in the power cable and turn on the scanner. . Reset the pick roller counter. Reset the pick roller counter by performing one of the following actions: Reset the counter in [4: Consumable Counters] on the [Settings Menu] screen of the Operator Panel. Reset the counter in the Software Operation Panel.* *For details, refer to the Operators Guide CG00002 ‐ 296501 ...
- Page 12 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Checking and resetting sheet counters Checking the sheet counters Start up the Software Operation Panel From the listing on the left, select The status of each consumable can be [Device Setting] viewed to determine when to replace or clean the consumables. The color of the counter gradually changes when a replacement for a consumable is needed or when cleaning is needed. The color of each counter changes as follows: Brake roller counter/pick roller counter These counters turn light yellow when the sheet count after the consumable replacement reaches 95% of the value specified in In this window, you can check the following ...
- Page 13 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Resetting the sheet counters When you have replaced or cleaned a consumable part, reset the corresponding counter by using the following procedure: If you have replaced a consumable, click the [Clear] button of the consumable that you replaced. If you performed cleaning, click the [Clear] button for [After cleaning]. The counter is reset to 0 For the Ink counter, the value will be set to 100 Click the [OK] button. A confirmation message appears. Click the [OK] button. The settings are saved CG00002 ‐ 296501 ...
-
Page 14: Cleaning Materials And Locations That Require Cleaning
FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Cleaning Materials and Locations that Require Cleaning Cleaning Materials Attention In order to use the cleaning materials safely and correctly, read the precautions on each product thoroughly. For more information about the cleaning materials, contact your FUJITSU scanner dealer or an authorized Fujitsu scanner service provider. CG00002 ‐ 296501 ... - Page 15 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Location and Frequency Attention Cleaning cycles may vary depending on the condition of the documents. Also, cleaning must be performed more frequently when the following types of documents are scanned: • Smooth – faced documents such as coated paper • Documents with printed text/graphics that almost cover the entire surface • Documents containing a large amount of calcium carbonate • Documents written in lead pencil • Documents on which the toner is not sufficiently fused CG00002 ‐ 296501 ...
-
Page 16: Cleaning The Outside
FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Cleaning the Outside The outside of the scanner, including the ADF paper chute (feeder) and the stacker, should be cleaned with either a piece of dry cloth, a cloth moistened with Cleaner F1/mild detergent, or a sheet of Cleaning Wipe. Attention To avoid deformation and discoloration, never use paint thinner or any other organic solvents. Be careful not to let moisture or water inside the scanner during cleaning. It may take a long time to dry if an excessive amount of Cleaner F1/mild detergent is used. Use it in small quantity. Wipe off the cleaner completely to leave no residue on the cleaned parts. CG00002 ‐ 296501 ... -
Page 17: Cleaning The Inside
FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Cleaning the Inside Cleaning the ADF (with Cleaning Paper) The ADF can be cleaned with a sheet of Cleaning Paper moistened with Cleaner F1. As the scanner continues to feed the documents, paper dust will accumulate inside the ADF and may cause scanning errors. Cleaning should be performed approximately every 10,000 sheets scanned. Note that this guideline varies depending on the types of documents you scan For instance, it may be necessary to clean the scanner more frequently when you scan documents on which the toner is not sufficiently fused. Attention • Do not use water or mild detergent to clean the ADF. • It may take a long time to dry if an excessive amount of Cleaner F1 is used. Use it in small quantity. Turn on the scanner. The [ready] screen is displayed on the LCD. Press the [Menu] button. The [Settings Menu] screen is displayed on the LCD. Press the [ ] or [ ] button and select [2: Cleaning], then press the [Scan/Enter] button to confirm. The [Cleaning] screen is displayed on the LCD. Select [1: Cleaning Paper] by the [ ] or [ ] button, and press the [Scan/Enter] button to confirm. A message is displayed on the LCD. CG00002 ‐ 296501 ... - Page 18 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Spray the cleaning paper with Cleaner F1. . Pull out the chute extension according to the length of the cleaning paper. . Pull out the stacker extension and lift up the stopper according to the length of the cleaning paper. . Load the cleaning paper in the ADF paper chute (Feeder). . Adjust the side guides to the width of the cleaning paper. Move the side guides by pressing the side guide buttons so that there is no space between the side guides and the cleaning paper. Otherwise the cleaning paper may be fed skewed. . Press the [Scan/Enter] button. The cleaning paper is fed and ejected onto the stacker. CG00002 ‐ 296501 ...
- Page 19 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Cleaning the ADF (with cloth) The ADF can be cleaned with a piece of cloth moistened with Cleaner F1, or a sheet of Cleaning Wipe. As the scanner continues to feed the documents, paper dust will accumulate inside the ADF and it may cause scanning errors. Cleaning should be performed approximately every 10,000 sheets scanned. Note that this guideline varies depending on the types of documents you scan. For instance, it may be necessary to clean the scanner more frequently when you scan documents on which the toner is not sufficiently fused. Attention • Do not use water or mild detergent to clean the ADF. • It may take a long time to dry if an excessive amount of Cleaner F1 is used. Use it in small quantity. Turn off the scanner and wait for at least 15 minutes. Unplug the power cable. Open the ADF. CG00002 ‐ 296501 ...
- Page 20 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Clean the following locations with a cloth moistened with Cleaner F1 or a sheet of Cleaning Wipe. CG00002 ‐ 296501 ...
- Page 21 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Brake Roller (× 2) Remove the roller from the scanner. Gently wipe off any dirt or dust along the grooves, taking care not to damage the roller surface. Pick Roller (× 5) Gently wipe dirt and dust off the roller surface (and along the grooves if it has grooves) as you rotate the roller by hand, taking care not to damage the roller surface. Make sure that it is wiped properly because black residue on the roller will affect the feeding performance. Rubber Roller (× 4) Gently wipe off any dirt or dust on the surface of the roller. Make sure that it is wiped properly because black residue on the rollers will affect the feeding performance. Be careful not to damage the sponge that is attached to the roller. Chute Roller (× 1) With the chute roller cover open, gently wipe off any dirt or dust on the surface of the ...
- Page 22 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Paper Path (× 2) Gently wipe the dirt and dust off the surface of the paper path. Glass (× 2) Gently wipe the dirt and dust off the surface of the glass sections. Ultrasonic Sensor (× 2)/Document Sensor (× 8) Gently wipe the dirt and dust off the surface of the ultrasonic/document sensors. CG00002 ‐ 296501 ...
- Page 23 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Feed Roller (× 2)/Eject Roller (× 2) The power must be turned on to rotate the feed/eject rollers. a. Plug in the power cable and turn on the scanner. The [Ready] screen is displayed on the LCD. b. Press the [Menu] button. The [Settings Menu] screen is displayed on the LCD. c. Press the [ ] or [ ] button and select [2: Cleaning], then press the [Scan/Enter] button to confirm. The [Cleaning] screen is displayed on the LCD. d. Press the [ ] or [ ] button and select [2: Roller Wipe], then press the [Scan/Enter] button to confirm. A message is displayed on the LCD. e. Open the ADF. ...
- Page 24 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS f. When you press the [Scan/Enter] button, the feed/eject rollers rotate a certain amount. Put a piece of cloth moistened with Cleaner F1 or a sheet of Cleaning Wipe against the surface of the feed rollers/eject rollers, and wipe horizontally. Wipe off any dirt or dust on the surface by pressing the [Scan/Enter] button to rotate the rollers. Make sure that it is wiped properly because black residue on the roller will affect the feeding performance. As a guideline, pressing the [Scan/Enter] button seven times will rotate the feed/eject rollers one revolution. CG00002 ‐ 296501 ...
- Page 25 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS . Close the ADF Reset the counter after cleaning. . CG00002 ‐ 296501 ...
-
Page 26: Cleaning The Flatbed
FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS Cleaning the Flatbed The Flatbed can be cleaned with a piece of cloth moistened with Cleaner F1, or a sheet of Cleaning Wipe. Open the document cover. Clean the document pad and document bed with a cloth moistened with Cleaner F1 or a sheet of Cleaning Wipe. Wait for the cleaned parts to dry. Gently close the document cover. CG00002 ‐ 296501 ... - Page 27 FI‐7600/FI‐7700 ONSUMABLE EPLACEMENT AND LEANING NSTRUCTIONS CG00002 ‐ 296501 ...
- Page 28 Fujitsu Computer Products of America, Inc. reserves the right to modify at any time without prior notice these statements, our products, their performance specifications, availability, price and warranty, post-warranty and ...