Table of Contents
Related Manuals for GE ZIRS36N LH
Summary of Contents for GE ZIRS36N LH
- Page 1 ® GE Monogram Installation Instructions Stainless Steel 36" Built-In Refrigerators and Freezers Models ZIRS36N LH - All Refrigerator ZIRS36N RH - All Refrigerator ZIFS36N LH - All Freezer ZIFS36N RH - All Freezer www.monogram.com...
-
Page 2: Table Of Contents
• Immediately repair or replace electric service Product failure due to improper installation is not cords that have become frayed or damaged. covered under the GE Appliance Warranty. See the • Unplug the refrigerator before cleaning or making Owners’ Manual for warranty information. -
Page 3: Flush Or Semi-Flush Enclosure Installations
Design Information 36" Stainless Steel Refrigerators, Freezers Advance Planning Flush or Semi-Flush Enclosure Installations 0" 3/4" True Flush Installation Semi-Flush Installation In a flush installation, These refrigerators the refrigerator door can also be installed will align evenly with the semi-flush into an enclosure front face of adjacent cabinet using the minimum cutout doors. -
Page 4: Installation Examples
Design Information 36" Stainless Steel Refrigerators, Freezers *Finished Width Side By Side Installation 2 1/2" Wall View Of Freezer 28 1/2" Electrical And Refrigerator 84" 7" 7" 5" 5" 24 3/4" Total 84 1/2" max 74" From Floor 83 1/2" min Depth to Bottom Finished... -
Page 5: Product Dimensions
10" Min. ZIFS36N RH, Freezer 24-3/4" 36" Overall Handle on the left side, the door swings left to right. ZIRS36N LH, Refrigerator ZIFS36N LH, Freezer Handle on the right side, the door swings right to left. CAUTION 26-3/4" 84-1/2" Max. -
Page 6: Installation Preparation
Installation Preparation 36" Stainless Steel Refrigerators, Freezers Two products installed side-by-side, both with hinges Clearances When installed into a corner: Allow 15" clearance on on left sides (or right sides) will require a 2" min. the hinge side for a 130° opening and full extension of clearance between the products. -
Page 7: Grounding The Refrigerator
Installation Preparation 36" Stainless Steel Refrigerators, Freezers Grounding IMPORTANT - (Please read carefully) Refrigerator FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR three-prong (grounding) wall receptacle to minimize REMOVE THE THIRD (GROUND) PRONG FROM THE... -
Page 8: Tools Required
Installation Preparation 36" Stainless Steel Refrigerators, Freezers • Appliance hand truck Tools • Tinsnips to cut banding • Drill and appropriate bits Required • Tubing cutter • Stepladder • 7/16" socket with 3" extension for • 7/16" open-end wrench • Bucket ratchet •... -
Page 9: Installation Instructions Step 2: Install Water Line
Installation 36" Stainless Steel Refrigerators, Freezers Step 2 • A cold water supply is required for automatic Install icemaker operation. The water pressure must be Freezer between 20 and 120 p.s.i. Water Line • Route 1/4" OD copper tubing between house cold water line and the water connection location. -
Page 10: Step 3: Install Side Panels
Installation 36" Stainless Steel Refrigerators, Freezers Step 3 • Side panels are required whenever the sides of the • If you choose to use 1/4" side panels, they should be Install product will be exposed and when installed between inserted into the case trim as illustrated. Fasten the Side panels to the product with velcro strips (provided) frameless cabinets. -
Page 11: Step 5: Level Refrigerator
Installation 36" Stainless Steel Refrigerators, Freezers Step 5 These products have a 4-point leveling system. The Level front is supported by leveling legs, the rear is Refrigerator supported by wheels. • Adjust rear wheels beneath the product to just barely touch the 2x4 block. Hex Nut Adjusts •... -
Page 12: Step 8: Connect Power
Installation 36" Stainless Steel Refrigerators, Freezers Step 8 • Connect the power cord plug to properly grounded Connect receptacle, accessible through the top left side of the Power hood opening. • Check to make sure power is on by opening the door to see if interior lights are on. -
Page 13: Step 11: Install Toekick
Stainless Steel Magic is available at Ace, True Value, Home Depot, Servistar, HWI and other leading stores. If any of these problems persist: It is also available through GE Parts by calling Call for Monogram local service in your area, 1-800-626-2002. Order part number WX10X15. -
Page 14: Zfc1 Trim Kit For Side To Side Installation
ZFC1 Trim Kit Side by Side Installation For the ultimate in convenience, install a refrigerator and freezer side by side. This trim kit includes 6 foam spacer pads to fill the gap between the side case trims. For a finished appearance, a trim strip is provided to conceal the side case trim of the two products. -
Page 15: Zugss Unified Grille Panel Kit
ZUGSS Trim Kit Unified Stainless Steel Custom Grille Panel Tools and materials Completion Time: Allow approximately 3 hours to Required: install this kit. • #1 and #2 Phillips screwdrivers or sockets • 1/4" angled wrench and 1-1/2" open ended IMPORTANT: 2 People are required to install this kit. wrench •... - Page 16 ZUGSS Trim Kit Unified Stainless Steel Grille Panel Soffit Block Step 2 CAUTION WARNING ANTI-TIP PRECAUTIONS Install These products are heavy at the top and must be Anti-Tip 83-1/2" From secured to prevent the possibility of tipping over. Brackets Floor Bottom of Wood ATTENTION...
- Page 17 ZUGSS Trim Kit Unified Stainless Steel Grille Panel Step 5 Case Trim • Open doors fully. Install Center • Starting at the top, press trim strip over inside case Trim Strip trims of both products. • Continue pressing trim until you reach the bottom of the case trims.
- Page 18 ZUGSS Trim Kit Unified Stainless Steel Grille Panel Step 7 Install Grille Base Unified Base Cover Place Cover Trim Over Hinges • Open doors fully. • Install the double width grille base cover by slipping the notched ends over the hinges. Install Install 3 Screws...
- Page 19 ZUGSS Trim Kit Unified Stainless Steel Grille Panel Step 9 Slip Dust Gasket Slip Second Dust Install Into Trim On One End Gasket Into Trim Soffit Vent Top • Separate the top and hinge side trim pieces by Reinstall removing side screws. Discard top piece, retain Screws screws.
- Page 20 ZUGSS Trim Kit Unified Stainless Steel Grille Panel Step 11 Adjust Door Alignment Bushing D o o r H i n C a s e H in g Raise Pin Shoulder 5/16" Wrench Check door alignment. The top of the door should be parallel with the grille panel.
- Page 21 Notes...
- Page 22 Notes...
- Page 23 Notes...
- Page 24 Note: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram local service in your area, call 1-800-444-1845. Note: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Pub.