Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear safety
instruction
footwear
manual
1. SAFETy
WARNING! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
‰
WARNING! TRAPPING DANGER – Although the vehicle lift movements are slow in operation, keep hands and limbs away from the steelwork
‰
during elevating and lowering.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip steel toe capped shoes.
9
Remove ill-fitting clothes. Remove ties, watches, rings, other loose jewellery.
9
Familiarise yourself with the applications, limitations and potential hazards of the vehicle lift.
9
once the load is lifted it is imperative that the load is locked by means of the anti-tilt arm.
9
DO NOT work under the vehicle without having first supported it with correctly rated axle stands.
8
The anti-tilt arm gives additional safety, but does NOT remove the need to use axle stands.
9
Use on a hard, level non-slippery surface such as concrete that is capable of supporting the load of the vehicle and the lift.
9
Check the load is stable on the lift, make sure there is no risk of tilting or slipping.
9
DO NOT try to move the vehicle when it is on the lift.
8
DO NOT modify the lift.
8
DO NOT drive onto the lift.
8
The lift is designed for lifting cars. Any other use is strictly forbidden.
9
When lifting or lowering a car DO NOT allow anyone other than the operator to approach the work area.
9
DO NOT use to achieve a task the vehicle lift was not designed to perform.
8
Follow the drill's instructions, because of the risks presented by an electrical supply DO NOT use near water.
9
DO NOT when lifting or lowering keep the vehicle balanced on the lift. The vehicle must rest freely on the front or rear wheels. Refer to
8
section 4 for the procedure.
DO NOT allow untrained persons to assemble or use the vehicle lift.
8
DO NOT lift the vehicle with people inside.
8
DO NOT exceed the load capacity of 1.5tonne. Refer to vehicle manufacturer's manual for weight of vehicle.
8
ensure adequate level space around the vehicle for the operator and the lift.
9
DO NOT operate the vehicle lift if parts are damaged or missing as this may cause failure and/or personal injury.
8
Before using lift, make a visual inspection of the vehicle lift to ensure there is no sign of damage or loose fixings.
9
Before commencing lift ensure the vehicle bodywork is structurally sound. Refer to manufacturer's manual for information as to whether
9
it is possible to lift the vehicle using the sills. modern vehicles make extensive use of sill covers and extensions. ensure there is sound
strong, steel to lift the weight on.
Before commencing the vehicle lift the vehicle hand brake must be off and leave in neutral.
9
‰ ‰ WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
‰
‰
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODuCTION
Compact and easy to raise a vehicle either manually or with an electric drill of 90nm or more (do not use an impact wrench as this will
damage the mechanism). during raising it can be stopped and at any height tilted.
3. SPECIFICATION
Model no ........................................................................PPL01
Capacity ........................................................................1500kg
Angled locking positions ..........................................................5
max. lift height ...............................................................585mm
overall size (W x d x H) .......................... 1185 x 775 x 160mm
© Jack Sealey limited
PORTABLE PIVOT CAR LIFT 1500KG
model no:
Warning!
Crushing of
hands
Original Language Version
PPL01
PPl01 | Issue 3 (4) 18/11/19
Advertisement
Related Manuals for Sealey PPL01
Summary of Contents for Sealey PPL01
- Page 1 PPL01 model no: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 4. CONTENTS Fittings Extension Extension Pieces Pieces Width 3 Width 2 Original Language Version PPl01 | Issue 3 (4) 18/11/19 © Jack Sealey limited...
- Page 3 Original Language Version PPl01 | Issue 3 (4) 18/11/19 © Jack Sealey limited...
- Page 4 ‰ 6.1.6.1. Take hold of the mini lift between the two drive housings and move it by rolling it on the castors located on the other side. Original Language Version PPl01 | Issue 3 (4) 18/11/19 © Jack Sealey limited...
- Page 5 6.2.8.5. Before reaching the minimum height, gradually slow the lowering speed. 6.2.9. Tilting WARNING! only for working on the front or the rear of the vehicle. ‰ Original Language Version PPl01 | Issue 3 (4) 18/11/19 © Jack Sealey limited...
-
Page 6: Maintenance
6.2.10.1. The drive nut for the load can wear over time or if it is badly lubricated. In this case, a safety device holds the load, but it is no longer possible to lift or lower it. DO NOT try to repair the mini lift so that you can continue to use it: only Sealey must be entrusted with the repair. 7. STORAGE 7.1.