Summary of Contents for jcb JCB-20IL
- Page 1 INSPECTION LAMP INSTRUCTION & USER MANUAL JCB-20IL Original Instructions IM-20IL-EN...
- Page 2 California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. The month and year of manufacture can be found within the product serial number e.g. MMYYPPPAXXXXX. Where production month (MM) and production year (YY) are included. JCB-20IL Instruction & User Manual...
-
Page 3: Table Of Contents
5. Battery tool use and care 6. Service CHARGER SAFETY COMPONENT LIST TOOL TECHNICAL DATA OPERATING INSTRUCTIONS Intended Use Battery Turning On/ Off To Hang the Inspection Light Adjustable Head Maintenance Transport and Storage WARRANTY STATEMENT GENERAL CERTIFICATE OF CONFORMITY JCB-20IL Instruction & User Manual... -
Page 4: General Power Tool Safety Warnings
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. JCB-20IL Instruction & User Manual... -
Page 5: Power Tool Use And Care
Use of any other accessories, or storing power tools. Such battery packs may create a risk of injury and fire. preventive safety measures reduce the risk of starting the power tool accidentally. JCB-20IL Instruction & User Manual... -
Page 6: Service
This will ensure that the safety of the power tool is maintained. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers. JCB-20IL Instruction & User Manual... -
Page 7: Charger Safety
To reduce risk of injury, only charge if they have been given supervision JCB rechargable batteries. The or instruction concerning use of charger and battery packs are specifically the appliance in a safe way and designed to work together. -
Page 8: Component List
SPOTLIGHT SWIVEL JOINT ANGLE JOINT ON/ OFF SWITCH GRIP J HOOK (NOT VISIBLE) CHARGER* BATTERY PACK* - PLEASE REFER TO TABLE ON PAGE 9 FOR BATTERY INFORMATION BATTERY TEST BUTTON AND CHARGE INDICATOR* *If applicable JCB-20IL Instruction & User Manual... -
Page 9: Tool Technical Data
Input Data Output Data JCB-20VFC AC 120 V, 50-60Hz, 70W 14.4 -20V d.c. 2.4A JCB-20VSFC AC 120 V, 50-60Hz, 105W 14.4 -20V d.c. 4.0A JCB-20DC AC 120 V, 50-60Hz, 200W 20.5V d.c. 2 x 3.5A JCB-20IL Instruction & User Manual... -
Page 10: Operating Instructions
Press the battery release button and remove stable surface. Plug the charger into a 230 V the battery from the tool. power point. Connect the battery to the charger so that it clicks into place. JCB-20IL Instruction & User Manual... -
Page 11: Intended Use
Make sure the power switch is not pressed and remove the battery from the charger. in when inserting or replacing the battery. Connecting the battery Use with JCB batteries only: JCB-20-15LI, JCB-20-20LI, JCB-20-30LI, JCB-20-40LI Connect the battery to the battery socket and JCB-20-50LI. -
Page 12: Turning On/Off
Regularly check all fasteners, screws and Lift the J hook from the slot. bolts to make sure that they are tight. Use the J hook to hang the inspection light. Tighten any loose screws immediately or serious injury could occur. JCB-20IL Instruction & User Manual... -
Page 13: Transport And Storage
Ensure that the tool is not at risk of tipping over or exposed to excessive vibration and shocks during transport, especially if the tool will be transported by car or other vehicle. NOTE Operating temperature: 0-40 °C Storage temperature: 20-60 °C JCB-20IL Instruction & User Manual... -
Page 14: Warranty Statement
In the unlikely event your JCB Power Tool is subject to a manufacturing fault within the warranty period, please contact the seller/retailer where the item was purchased. JCB Power Tools used for Hire Fleets or as part of B2B and Service Contracts are not covered by these terms and conditions. - Page 15 JCB-20IL Instruction & User Manual...
-
Page 16: General Certificate Of Conformity
IEC 55015:2013+A1 IEC 61547:2009 IDENTIFICATION DETAILS OF IMPORTE DOMESTIC MANUFACTURER CERTIFYING PRODUCT COMPLIANCE: Name: JCB Tools (Yellow and Black Tools Limited) Address: 55 Romsey Industrial Estate Romsey, SO51 0HR Tel no: +44 1794 834250 CONTACT INFORMATION OF INDIVIDUAL MAINTAINING RECORDS OF TEST RESULTS: Name: Tim Burgoyne, QA Technical Manager &... - Page 17 JCB-20IL Instruction & User Manual...