Related Manuals for Samsung SADT-103WM
Summary of Contents for Samsung SADT-103WM
- Page 1 SADT - 103WM Wall Mount Adaptor imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/global/register SADT-103WM_ENG.indd 1 2008-03-18 오전 9:13:51...
-
Page 2: Installation
Overview The Wall Mount Adapter is used to install the OUTDOOR HOUSING (SHG-221/222) on the indoor/outside wall. Notice • Make sure that you must select an installation spot to endure the total weight of "Wall Mount Adapter", "Outdoor Housing" and "Smart Dome Camera". •... -
Page 3: Cover Plate
The wiring diagram to connect the outdoor cable of the OUTDOOR HOUSING(SHG-221/222) 3. If you mount the Wall Mount Adaptor on the wall, mark a hole where you insert the anchor bolt or anchor nut (M10) using the Cover Plate, and drill a hole for the anchor bolt (nut). If you install it in a corner of the wall, use the Corner Mount Adaptor (SADT-110CM). - Page 4 4. Prepare the Holder Housing from the Outdoor Housing and insert the cables of the Holder Housing into the Wall Mount Adaptor before pulling them out through the hole of the Cover Fixing Part. WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR The place for joining a COVER CABLE HOLDER HOUSING...
- Page 5 6. Turn the Holder Housing clockwise by 18 degrees. Then, use 3 screws(M4×L8, suported), to fix the Holder Housing to the Wall Mount Adaptor. WALL MOUNT ADAPTOR WALL MOUNT ADAPTOR SCREW HOLDER HOUSING HOLDER HOUSING Turn to the clockwise about 18 degrees 7. According to the status of connected cable of the OUTDOOR HOUSING, SHG-221/222), a way of installation is different as follows.
- Page 6 If you use only the Grand Cable to fix the cables to the Cover Plate, the other hole of the Cover Plate should be sealed up with the Rubber Cap for waterproofness. COVER PLATE 150 mm CABLE GRAND RUBBER CAP ...
- Page 7 If the cable pipe is installed outside of the wall Drill a 21mm-diameter hole on the Wall Mount Adaptor (side and top, respectively). For your reference, see the figure below. - The drilling process for the Wall Mount Adaptor must be performed prior to the fixing process of the Holder Housing according to the steps 4, 5, 6 in this installation guide.
- Page 8 Use the Grand Cable to fix the necessary cables to the Wall Mount Adaptor before pulling them out of the hole of the Cover Fixing Part. The place for joining a COVER WALL MOUNT ADAPTOR CABLE GRAND Use 6 screws (Flat, M3xL8) to fix the Cover Plate to the Wall Mount Adaptor. - Make sure that the Gasket part should keep contact with the Wall Mount Adaptor during the fixation.
- Page 9 9. See the wiring diagram below for connecting the cables of the Camera Adaptor. A. Remove one of the Connectors connected to the cable end of the Camera Adaptor. B. Peel off the coating on the cable end of the Connector and connect it to the external cable using soldering.
- Page 10 0. Insert the joined cable into the Wall Mount Adaptor through the Cover Fixing Part. Insert one piece of the two-strand cable into an empty area of the Wall Mount Adaptor as in the figure below and push the other one into the Wall Mount Adaptor. (Ensure that the insulated coating of the cable should be kept intact while the insertion) the place for joining a cover WALL MOUNT ADAPTOR...
- Page 11 2. Now you can couple the Outdoor Housing with the Holder Housing and do the same with the Cover Front and the Cover Rear. (For more information, see the installation guide for the Outdoor Housing (SHG-221/ SHG-222).) WALL MOUNT ADAPTOR COVER FRONT COVER REAR OUTDOOR HOUSING...
-
Page 12: Product Specification
Product Specification Location for use: Indoors or outdoors Installation Spot: Wall or Vertical Structure Dimension: See the figure Weight: 1,250g Material: aluminium Operation Temperature: -40˚C ~ 50˚C HUMIDITY: 0~100% Accessories Cover Plate ........1 (Gasket Attached) Cover ..........1 Screw (flat, M3xL8) ......6 (For fixing Wall Mount + Cover Plate) Screw (M3xL4) ......... -
Page 13: Correct Disposal Of This Product
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.