55" class (54.6" diag.) sony led hx850 internet tv (40 pages)
Summary of Contents for Sony X900E Series
Page 1
SERVICE MANUAL *Table of contents is on the last page. Please also utilize "Bookmarks“ function / "Find" function on Acrobat PDF data. X900E Series ORIGINAL MANUAL ISSUE DATE: 1/2017 GN3TR CHASSIS KS Segment Version Date Subject 1/2017 Original manual issue.
Page 2
MODEL LIST MODEL COLOR COMMANDER DEST. MODEL COLOR COMMANDER DEST. XBR-49X900E Black RMF-TX200U (UC2) US/CND XBR-55X900E Black RMF-TX200U (UC2) US/CND (LA1) MEXICO XBR-65X900E Black RMF-TX200U (UC2) US/CND (LA1) MEXICO XBR-75X900E Black RMF-TX200U (UC2) US/CND (LA1) MEXICO XBR-49/55/65/75X900E...
Page 3
Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.
Page 4
Ne les remplacer que par des composants Sony dont le numero de piece est indique dans le present manuel ou dans des supplements publies par Sony. Les reglages de circuit dont l’importance est critique pour la securite du fonctionnement sont identifi es dans le present manuel.
Page 5
WARNINGS AND CAUTIONS USE CAUTION WHEN HANDLING THE LCD PANEL When repairing the LCD panel, be sure you are grounded by using a wrist band. When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover. Do not press on the panel or frame edge to avoid the risk of electric shock.
Page 6
SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges. 2.
Page 7
SAFETY CHECK-OUT Leakage Test (To protect electric shock when customer touch the terminal.) Leakage current can be measured by V: Voltmeter or oscilloscope (r.m.s. or peak reading) Stabilized power supply instrument and isolated voltage transformer: Use too much current capacity and isolated voltage transformer does not need to use stabilized power supply equipment Specification of RMS volt meter: Input resistance >...
Page 8
SELF DIAGNOSIS FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash. The number of times the LED flashes translates to a probable source of the problem. A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 9
SELF DIAGNOSIS FUNCTION [SELF DIAGNOSTIC SCREEN DISPLAY] Error count Error Item SELF CHECK Format of error timestamps YYMMDDhhmmss (in UTC) Back << Example: MAIN POWER 000000000000 000000000000 000000000000 120823132523 -> Aug 23 2012 13:25:23 UTC DC ALERT 000000000000 000000000000 000000000000 * Only when time is set, an error timestamp is saved.
Page 10
ADJUSTMENT HOW TO ENTER SERVICE MODE 1) Turn on the main power switch to place the set in standby condition. 2) Press the buttons on the remote commander as follows, and entering service mode. 3) Service mode display. Service Mode Model Information >>...
Page 11
ADJUSTMENT SOFTWARE VERSION 1) In Service Mode, select “Model Information”, press “Enter” or “→” button to enter Status Information. Main Micro Service Mode SW Version: PKG1.1.0.03.26.1.00.0 Model NVM Version: 0043 CEI Model Information >> Boot Version: V1.00000000 PQ Version: 02000001 Status Information Self diagnosis History >>...
Page 12
ADJUSTMENT SERIAL NUMBER EDIT (1) Service Mode 1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” button then pressing “Enter” or Model Information >> “→” button to enter inside. Self diagnosis History >> Video / Audio >> 2) Select “Serial Number Edit”...
Page 13
ADJUSTMENT SERIAL NUMBER EDIT (2) YES is selected, the input data is saved into EEPROM. Model SERIAL NUMBER EDIT is grayed out and the serial number that has been input is displayed. Status Information >> Operator will not be able to edit anymore.
Page 14
ADJUSTMENT MODEL NUMBER SETTING 1) In “Service Mode”, select “Model Information” by pressing “↑” or “↓” button then pressing “Enter” or “→” button to enter inside. 2) Select “Model Number Setting” by pressing “↑” or “↓” button then pressing “Enter” or “→” button. 3) Press “↑”...
Page 15
ADJUSTMENT WB ADJUSTMENT (If necessary) c. To change data, press “←” or “→” button on remote commander. In “Panel/PQ” service mode. a. Go to “WB Adjustment” category by “↑” or “↓”. Service Mode Back << R WB Gain <[ ]> Model Information >>...
Page 16
ADJUSTMENT WB/MURA/CUC DATA TRANSFER 2. In “WB/Mura/CUC data transfer”. a. Select “WB/Gamma data transfer” by pressing “↑” or “↓” button on remote commander. (Please apply Main board or panel is replaced.) b. To change the items, press “←” or “→” button on remote commander and press “Enter” 1.
Page 17
USB UPDATE *Please refer to another manual “Service Procedure for Panel, Board and Software Change / Upgrade(P/N:98881800x)” for details. GN3TR chassis is the same as GN1T chassis basically. 1:Download USB image and unzip file. 2: copy unzip file to USB memory root folder. 3: USB memory insert TV.
Page 18
TROUBLE SHOOTING TRIAGE Confirm the symptom from the customer. Select that symptom from the chart. Bring all the boards and cables listed for that symptom. Follow the troubleshooting charts in the technical guides to isolate the board. Chart Color Code. RED DOT: Most likely defective part BLUE TRIANGLE: Secondary possible defective part BLACK TEXT: Board that may correct the symptom...
Page 19
TROUBLE SHOOTING FLOW 1-1. NO POWER WITH G* BOARD No Power Check STBY 3.3V Replace C518 Between G* board to G* board near CN400 B* board Harness on B* board Harness B* board u-Com Failure DDCON/LDO Main Device Failure XBR-49/55/65/75X900E...
Page 20
TROUBLE SHOOTING FLOW 1-1. NO POWER WITH AC-ADP No Power (Both side are No power.) AC Adaptor Check POWER_MAIN (Only single side is 19.5V or 24V.) Replace Check C409 Between JK* board to F9000 F9000 near CN400 B* board Harness On JK* board on B* board (Both side are...
Page 21
TROUBLE SHOOTING FLOW 1-2. NO POWER U-COM FAILURE START Check 12V_MON Check +12V_MAIN Line Check VDD Check +3.3V_STBY LIne (C521, CN400 #14pin) R446 Voltage. C506 Voltage. And (only for AC-ADP model) (G board or JK board). Is the voltage >2.6V? Is the voltage >3.0V? 3.3V_DDCON (IC403) (only for AC-ADP model)
Page 22
TROUBLE SHOOTING FLOW 1-2. NO POWER U-COM FAILURE Previous page Check P_ON_#2 CL417 or P-on ucom #pin13 Change IC401 is >3.0V? Check P_ON_HL CL414 or P-on ucom #pin18 Change IC401 is >3.0V? Check ORESETB CL416 or P-on ucom #pin14 Change IC401 Is the voltage >3.0V? Check X_SYSTEM_RST CL412 or P-on ucom #pin20...
Page 23
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO DDCONs CHECK ON JK* START Check fuse F9001 Change Fuse Is fuse OK? (Both side are No power.) AC Adaptor Check Vcc voltage Check C9023 F9000 F9000 Is voltage >18V? On JK* board (Only single side is 19.5V or 24V.) (Both side are...
Page 24
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO DDCON CHECK START Check IC402 Vcc voltage Check Vcc voltage Check C423 C602 D600 Change D600 Is voltage >12V? Is voltage >3V? Is diode alive? Check +3.3V_STBY. G* board or IC403 Check Vcc voltage Check C602 D601...
Page 25
TROUBLE SHOOTING FLOW 1-3. NO POWER DDCON/LDO LDOs CHECK DDCONs CHECK START START Check fuse Check +3.3V_DDC_OUT Check Vcc voltage DDCON (IC403) F4xx or F6xx Change Fuse C6xx Is fuse OK? Is voltage >3V? +3.3V_STBY (G* board) 1) Check POWER_ON P-on ucom #pin10 Check Vcc voltage (Refer No Power U-Com Failure) Check Enable pin...
Page 26
TROUBLE SHOOTING FLOW 2-1. LED BLINKING 2X (MAIN POWER ERROR) LED 2X blinking Check “+12V_MAIN” G board at pin 11/13 of CN400 JK board on B* board, AC Adaptor Voltage > 13.2V ? BMKS / BMKP board XBR-49/55/65/75X900E...
Page 27
TROUBLE SHOOTING FLOW 2-2. LED BLINKING 3X (DC ALERT AND AUDIO ERROR) DC_ALERT AUDIO ERROR 3-times blinking 3-times blinking (Audio Error) (DC Alert) Power Off Check Go to No Sound (Power Off Check) Check “POWER_MAIN” at pin 17/19 of CN400 Check “+5.0V_VBUS”...
Page 28
TROUBLE SHOOTING FLOW 2-3. LED BLINKING 4X (LED VOLTAGE ERROR AND BCM ERROR) LED VOLTAGE ERROR 4-times blinking (LED Voltage) Check “+1.8V_TU” Check “BL_LD_ERR” at C464 at CL1038 on BMKS board Replace LD board Panel on BMKS board 0.95V < Voltage < 1.85V ? Voltage >...
Page 29
TROUBLE SHOOTING FLOW 2-4. LED BLINKING 5X (PANEL ID READ ERROR) 5-times blinking Check Replace “+12.5V_TCON” G/JK board G/JK board at C400 on BMKS Symptom improve Replace the Harness Between G/JK board Harness and BMKS Symptom improve Replace V-By-One FFC the V-By-One FFC is suspicious Symptom improve...
Page 30
TROUBLE SHOOTING FLOW 2-5. LED BLINKING 6X (BACKLIGHT ERROR) 6-times blinking Harness / Connection Symptom Voltage ≥ 1.9 V Check Voltage of Check broken Improvement Replace “BL_LD_ERR_DET” harness/connection Harness harness at CL1038 on BMKS G/LD board to BMKS improvement Voltage < 1.9 V Symptom Harness / LED driver or G board...
Page 31
TROUBLE SHOOTING FLOW 2-6. LED BLINKING 7X (TEMPERATURE ERROR) 2-7. LED BLINKING 8X (4KPQ ERROR) 7-times blinking 8-times blinking Setting circumstance is OK? Set to another improvement Replace Temperature, location, etc. Other flows BMKS board Ventilation, etc. Symptom Improvement Replace BMKS/BMKP board, and Aging a few Panel BMKS board...
Page 32
TROUBLE SHOOTING FLOW 3-1. NO SOUND No Sound Without LED 3x Select [External Inputs] AV receiver is connected [BRAVIA Sync Settings] to HDMI in ? [BRAVIA Sync Control] [off] No sound only Go to Analog RF and Digital RF ? 3.5 NO SOUND ( TUNER) [Speakers] setting is Change the setting to...
Page 33
TROUBLE SHOOTING FLOW 3-2. NO SOUND (POWER OFF CHECK) 3-3. NO SOUND (POWER ON CHECK) PVDD (POWER_AU) voltage is 240W AC Adaptor model : 24.0V Power On Check Power Off Check 200W AC Adaptor model : 19.5V Power Off Check From 2.2 LED BLINKING 3X From 2.2 LED BLINKING 3X Built-in power supply model : 12.5V...
Page 34
TROUBLE SHOOTING FLOW 3-4. NO SOUND (AUDIO HP/AUDIO OUT) 3-5. NO SOUND ( TUNER) No Sound Audio No Sound with normal picture HP/Audio out [Sound]→ [Headphone] Headphone Volume Increase Headphone Volume [Headphone/Audio out] is set to MIN? is set to ? Only RF tuner input? Replace B* board [Audio Out (Fixed)]...
Page 35
TROUBLE SHOOTING FLOW 3-6. NO SOUND (HDMI) No Sound Check the picture Refer to NO PICTURE (HDMI) Does this model have Check the mode Connect Stereo minijack cable between Source and the TV, Analog Audio In of Source equipment And Change “HDMI/DVI Audio Source” to Auto or Analog Audio In. (Stereo minijack)? HDMI Change the mode of Source equipment to HDMI...
Page 36
TROUBLE SHOOTING FLOW 4-1. NO PICTURE No Picture BL_ON (L or H): IC401 #7pin (for 4K BMKS/BMKP board) BL_ON:H Check Smart Core Check Replace Got Any Normal Replace LCD Panel Behavior BL_ON the V by One FFC Display? The B board (T-CON) (5x Blinking) on the B board...
Page 37
TROUBLE SHOOTING FLOW 4-2. NO PICTURE (VIDEO 1/VIDEO 2/COMPONENT) VIDEO 1 No Picture Video 1 No Picture Check J2601 Check if input OSD NG (Vpp: 0V) Connection, is GRAY OUT VIDEO_DET OK if it is highlighted At R2631 OK (Vpp: 3.3 V) Detailed check all NG (Vpp: 0V) parts at VIDEO2_DET...
Page 38
TROUBLE SHOOTING FLOW 4-2. NO PICTURE (VIDEO 1/VIDEO 2/COMPONENT) COMPONENT / VIDEO 2 No Picture Component Video 2 No Picture No Picture Check if input OSD NG (Vpp: 0 V) Check J2600 Con Check J2600 Check if input OSD is GRAY OUT NG (Vpp: 0 V) Connection, VIDEO_DET at R2626,...
Page 39
TROUBLE SHOOTING FLOW 4-3. NO PICTURE (TUNER) RF input no picture / noisy picture Notes: I2C I2C line for all tuners except Japan_SKP - Parts for I2C SDA line: R2800, C2803. Check RF source cable Change RF cable and antenna - Parts for I2C SCL line : R2801, C2804.
Page 40
TROUBLE SHOOTING FLOW 4-4. NO PICTURE (TUNER) FOR ANALOG TUNING Analog Tuning For LA-ISDB(BR/AR), LA-T2(COL) and TW only For Other destination Notes: Confirm ANT or Cable connection - Parts for IFOUT_N line : FB2801, C2807, C2826 - Parts for IFOUT_P line : FB2802, C2808, C2825 - Parts for IFAGC line : R2838, C2827 : Insert correct signal in correct terminal.
Page 41
TROUBLE SHOOTING FLOW 4-4. NO PICTURE (TUNER) FOR DIGITAL TUNING 1 Digital Tuning 1 For TW/LA-ISDB-T Notes: - Parts for IFOUT_N line : FB2801, C2807, C2826 - Parts for IFOUT_P line : FB2802, C2808, C2825 - Parts for IFAGC line : R2838, C2827 For NA-ATSC(MX/UC) Confirm ANT or Cable connection...
Page 42
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI1 No Picture Check the below point at All lines Connector side are NG Other Input is OK Check other - Check +5V line Replace HDMI input - Check HPD line CN3603 - Check DDC lines - Check TMDS lines All Inputs are NG TMDS lines...
Page 43
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI2 No Picture Check the below point at All lines Connector side are NG Other Input is OK Check other - Check +5V line Replace - Check HPD line HDMI input CN3600 - Check DDC lines All Inputs are - Check TMDS lines Other TV set...
Page 44
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI3 No Picture Check the below point at All lines Connector side Other Input is OK are NG Check other - Check +5V line Replace HDMI input - Check HPD line CN3601 - Check DDC lines All Inputs - Check TMDS lines are NG...
Page 45
TROUBLE SHOOTING FLOW 4-5. NO PICTURE (HDMI) HDMI4 No Picture Check the below point at All lines are Connector side Other Input is OK - Check +5V line Replace Check other HDMI input - Check HPD line CN3602 - Check DDC lines All Inputs - Check TMDS lines are NG...
Page 46
TROUBLE SHOOTING FLOW 5. KEY SWITCH BUTTONS ERROR Side key buttons error Check harness connection between B*board and switch Harness connection issue module Resistor value [BMKS] Change harness between B* B* board to switch module harness R1108 : 0 [ohm] board to switch module issue R1049 : 47k [ohm]...
Page 47
TROUBLE SHOOTING FLOW 6. IR REMOTE COMMANDER ERROR IR remote commander does not respond Center white LED blinks when Battery of remote commander pushing buttons of remote could be weak. commander at close to IR Change battery. sensor. Check harness connection Harness connection between B*board and Smart issue...
Page 48
TROUBLE SHOOTING FLOW 7. LIGHT SENSOR ERROR Backlight level does not change when ambient light changed Setting is “ON” Check UI setting and make Check harness connection Battery of remote commander sure light sensor setting is between B*board and Smart could be weak.
Page 49
TROUBLE SHOOTING FLOW 8. NETWORK MALFUNCTION ETHERNET (WIRED) [Network Set-up] >[Wired Set-up] on the TV Connection Results Connection Results Connection Results B* board Cable Connection Local Access Internet Access Failed Failed Failed Auto Check Wired Set-up Check cable B* board Local router Proxy setting IP address setting...
Page 50
TROUBLE SHOOTING FLOW 9. NETWORK MALFUNCTION INTERNAL WIRELESS NETWORK MALFUNCTION Wireless Network on the TV Is the Wi-Fi radio Error message or no scan result appear in strength too weak B* board the network setting? or even No signal? Check with another Wi-Fi Access Point Hardware defect suspected module...
Page 51
TROUBLE SHOOTING FLOW 10. BLUETOOTH MALFUNCTION Voice Remote doesn’t work 3D-glasses (Active) doesn’t work Bluetooth Speaker/Headphone/Headset doesn’t work Please refer Voice Remote manual Check BT antenna Home > Settings > 3D-glasses (Active) manual Connection is OK Bluetooth Settings Can read Bluetooth Speaker/Headphone/Headset operation manual Near discoverable Bluetooth Device...
Page 52
TROUBLE SHOOTING PCB PARTS MAP BMKS (A side view) XBR-49/55/65/75X900E...
Page 53
TROUBLE SHOOTING PCB PARTS MAP BMKS (B side view) XBR-49/55/65/75X900E...
Page 54
BLOCK DIAGRAMS * depend on destinations. Some control lines are left out. Some control lines are left out. BMKS board * IR In Center Key RGBW LEDs Video signal * CAS/CI DDCs Audio signal L/R Keys Light Sens. Control Bus IR Rx Power * RF...
Page 59
BOARD LOCATION XBR-49X900E XBR-55X900E LD30 LD35 TSA2 BMKS TSA2 BMKS E-T-CON SWITCH UNIT E-T-CON SWITCH UNIT WLAN/BT MODULE(11AC) SMART CORE (S) UNIVERSAL SIL-TU WLAN/BT MODULE(11AC) SMART CORE (S) UNIVERSAL SIL-TU XBR-65X900E XBR-75X900E SMART CORE (S) LD75 HSC3-L BMKS SWITCH UNIT TSA2 SWITCH UNIT LD45...
Page 60
WIRE DRESSING *This page is only the information which shows each rough location. XBR-49X900E XBR-55X900E VA Tape Slide Clamp x1 VA Tape Slide Clamp x2 Harness Tie x4 Harness Tie x5 ・Fix wire • Fix wire • Hold wires ・Fix wire •...
Page 61
PANEL HANDLING CARRYING 1. Carry panel vertically. 2. Do not hold or press O-Cell. 4. Do not hold the panel at the center area. 3. Hold panel by 2 people. XBR-49/55/65/75X900E...
Page 62
PANEL HANDLING PLACING TO TABLE Holding corner 1. Put the Panel by 2 operators. 2. Put the Panel within one flat table surface. XBR-49/55/65/75X900E...
Page 63
PANEL HANDLING OTHERS 1. Do not press the panel during assembly / disassembly. 2. Do not touch Panel module without gloves. 4. Do not grasp the BC hook. 5. Do not grasp the LD Shield. 3. Do not grasp Source Shield. XBR-49/55/65/75X900E...
Page 64
DISASSEMBLY • There are clutch in the yellow frame[ ]. Therefore please be careful in the case of the disassembly or assembly of parts. • [ ] indicates the part to disconnect or remove from the connectors or clampers. 1. XBR-55X900E 1-1.
Page 77
DISASSEMBLY 1. XBR-55X900E 1-15. SWITCH UNIT (3M-P) AND HOLDER SIDE SW (SBT M) Screw (SCREW M3X3.0 STEP) P/N: 4-579-926-01 SWITCH UNIT (3M-P) HOLDER SIDE SW (SBT M) XBR-49/55/65/75X900E...
Page 81
DISASSEMBLY 1. XBR-55X900E 1-19. BRACKET, DC JACK (SBT) AND JK3 BRACKET, DC JACK (SBT) 4 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 86
DISASSEMBLY 1. XBR-55X900E 1-24. BRACKET, SIDE (SBT) BRACKET, SIDE (SBT) XBR-49/55/65/75X900E...
Page 87
DISASSEMBLY 1. XBR-55X900E 1-25. BRACKET, IR IN AND IR (UC2 ONLY) Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 88
DISASSEMBLY 1. XBR-55X900E 1-25. BRACKET, IR IN AND IR (UC2 ONLY) NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 102
DISASSEMBLY 2. XBR-65X900E 2-1. STAND NECK (R) (L SBT) A AND STAND NECK (L) (L SBT) A AND STAND BASE (L SBT) A 4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND NECK (R) (L SBT) A STAND NECK (L) (L SBT) A STAND BASE (L SBT) A 4 screws ( SCREW, STAND (SBT)) P/N: 4-692-700-01 XBR-49/55/65/75X900E...
Page 119
DISASSEMBLY 2. XBR-65X900E 2-19. BRACKET, DC JACK (SBT) AND JK BRACKET, DC JACK (SBT) 4 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 124
DISASSEMBLY 2. XBR-65X900E 2-24. BRACKET, SIDE (SBT) BRACKET, SIDE (SBT) XBR-49/55/65/75X900E...
Page 125
DISASSEMBLY 2. XBR-65X900E 2-25. BRACKET, IR IN AND IR (UC2 ONLY) Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 126
DISASSEMBLY 2. XBR-65X900E 2-25. BRACKET, IR IN AND IR (UC2 ONLY) NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 141
DISASSEMBLY 3. SMART CORE (S) 3-4. HSC3-L AND CASE, BOTTOM (SBT) NOTE: CASE, BOTTOM (SBT) HSC3-L XBR-49/55/65/75X900E...
Page 142
DISASSEMBLY 4. XBR-75X900E 4-1. STAND NECK (R) (3L SBT) A AND STAND NECK (L) (3L SBT) A AND STAND BASE (3L SBT) A 4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND NECK (R) (3L SBT) A STAND NECK (L) (3L SBT) A STAND BASE (3L SBT) A 4 screws ( SCREW, STAND (SBT)) P/N: 4-692-700-01 XBR-49/55/65/75X900E...
Page 168
DISASSEMBLY 4. XBR-75X900E 4-28. BRACKET, SIDE (SBT) BRACKET, SIDE (SBT) XBR-49/55/65/75X900E...
Page 169
DISASSEMBLY 4. XBR-75X900E 4-29. BRACKET, IR IN AND IR (UC2 ONLY) Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 170
DISASSEMBLY 4. XBR-75X900E 4-29. BRACKET, IR IN AND IR (UC2 ONLY) NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 180
DISASSEMBLY 4. XBR-75X900E 4-39. WIRE DRESSING AND T-CON(75) WITH SHEET AND RUBBR 4 screws (SCREW, M3X3.5) T-CON(75) NOTE: When you replace T-CON(75), please make sure that the following parts are attached on new T-CON(75). SHEET 2pcs RUBBER 2pcs B SIDE A SIDE XBR-49/55/65/75X900E...
Page 182
DISASSEMBLY 5. XBR-49X900E 5-1. STAND NECK (ML SBT) A AND STAND BASE (ML SBT) A 4 screws (SCREW, +PSW M5X12) P/N: 2-580-607-01 Screw (SCREW, +PSW M5X12) P/N: 2-580-607-01 STAND NECK (ML SBT) A STAND BASE (ML SBT) A XBR-49/55/65/75X900E...
Page 194
DISASSEMBLY 5. XBR-49X900E 5-14. SWITCH UNIT (3M-P) AND HOLDER SIDE SW (SBT M) Screw (SCREW M3X3.0 STEP) P/N: 4-579-926-01 SWITCH UNIT (3M-P) HOLDER SIDE SW(SBT M) XBR-49/55/65/75X900E...
Page 201
DISASSEMBLY 5. XBR-49X900E 5-21. BRACKET, DC JACK (SBT) AND JK3 BRACKET, DC JACK (SBT) 4 screws (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 202
DISASSEMBLY 5. XBR-49X900E 5-22. SLIDE, CLAMP AND BRACKET, SIDE (SBT-M) SLIDE, CLAMP BRACKET, SIDE (SBT-M) XBR-49/55/65/75X900E...
Page 203
DISASSEMBLY 5. XBR-49X900E 5-23. BRACKET, IR IN AND IR Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 204
DISASSEMBLY 5. XBR-49X900E 5-23. BRACKET, IR IN AND IR NOTE: BRACKET, IR IN Screw (SCREW, +PSW M3X6) P/N: 4-472-518-11 XBR-49/55/65/75X900E...
Page 219
EXPLODED VIEWS • Items with no part number and no description are not stocked because they are seldom required for routine service. • The construction parts of an assembled part are indicated with a collation number in the remark column. •...
Page 220
EXPLODED VIEWS 1. XBR-55X900E LCD PANEL REF. No. PART No. DESCRIPTION MARK A-2170-004-A P-MOD (YD7S550DND01B) 4-588-223-01 SHEET, THERMAL (TPZ BBE) 4-549-186-01 SHEET, THERMAL(BM) 4-690-221-01 CUSHION, CORNER(SBT) 4-598-764-61 BRACKET, SIDE (SBT) FOR UC2 4-598-764-11 BRACKET, SIDE (SBT) FOR LA1 A-2170-502-A COMPL SVC BMKS_UC_KS FOR UC2 A-2170-504-A COMPL SVC BMKS_MX_KS...
Page 240
EXPLODED VIEWS 6. OTHER PART ACCESSORIES REMOTE COMMANDER (RMF-TX200U) BAG, SCREW A (CCT) P/N: 1-493-127-31 P/N: 4-462-871-02 SCREW, +PSW M5X12 2-580-607-01 STAND NECK (L) (3L SBT) A P/N: 4-686-205-01 BAG,SCREW A (SBT) AC ADAPTOR (200W) P/N: 4-689-279-01 P/N: 1-493-326-11 SCREW, STAND (SBT) 4-692-700-01 STAND NECK (R) (L SBT) A P/N: 4-686-204-01...
Page 241
EXPLODED VIEWS 6. OTHER PART MISCELLANEOUS PART No. DESCRIPTION MARK ∗ 4-548-743-01 HOLDER, HS WS (MUF) FOR BMKP ∗ 4-549-188-01 HOLDER(HS MUF) FOR BMKP ∗ 4-584-547-01 HEAT SINK(MUFF2 C) 4-687-148-01 SHEET, THERMAL (PIQ A) ∗ 4-687-840-01 HEAT, SINK(MS) w/ cut out portion ∗...
Page 243
APPENDIX-1 Voice Remote Control • This remote has the following functions: • Key “MIC” key: Bluetooth • Voice search • Key codes (except “MIC” key) are sent by IR code. You can control all TVs without pairing. • “MIC” key code and voice data are sent by Bluetooth. Voice search function could be used with only the paired TV.
Page 244
APPENDIX-1 Setting Voice Remote Control To register the Voice Remote Control to the TV 1. Press the HOME button, select [Settings] [Voice Remote Control] [Activate the button] then, follow the on-screen instruction. 2. Prepare Voice Remote Control. 3. Press and hold down the Volume-down key. 4.
Page 245
APPENDIX-2 Reset vs. Factory Reset Reset: Press and hold down the power button (approx. 5 seconds) on the remote commander until the message “Power off” appears on the TV screen The TV will turn off, and then restart automatically Try a reset when Android TV doesn’t behave properly (e.g., the TV is unresponsive or is stuck on a black screen). Note if you unplug and plug in the power cable, it may have the same effect as a reset.
Page 246
APPENDIX-3 Other part replacement which synchronize with panel replacement ex. The figure is 65 " CUSHION, CORNER(SBT) CUSHION 825C (Himeron tape) *LABEL, SIDE TERMINAL 49”/55”/65” : 4pcs 65” only (SBT) is necessary for Panel 75” : 2pcs replacement. XBR-49/55/65/75X900E...
Page 247
Table of contents F COVER APPENDIX-1 MODEL LIST Voice Remote Control WARNINGS AND CAUTIONS How to use voice search function SAFETY CHECK-OUT Setting Voice Remote Control SELF DIAGNOSIS FUNCTION APPENDIX-2 ADJUSTMENT Reset vs. Factory Reset USB UPDATE APPENDIX-3 TROUBLE SHOOTING Other part replacement which synchronize with panel replacement TRIAGE FLOW...