Page 1 Satellite Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 158 in this guide.
Page 2 TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA,...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port microphone jack (Port availability depends on model selected).
Page 4: Industry Canada Requirement
Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com. ❖ Or call the Toshiba Global Support Centre: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003.
Page 5: Telephone Company Procedures
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers.
Page 8: Regulatory Information
The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Page 9 EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: This product is carrying the CE-Mark in accordance with the related European Directives. The party responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany.
Page 10 Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Page 11: Device Authorization
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 12: Radio Approvals For Wireless Devices
JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only.
Page 13 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 14 Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries European Community Countries Austria Belgium, France, Switzerland/Lichtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK Iceland, Spain O: allowed x: forbidden ❖...
Page 15 ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area.
Page 16 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Approved Countries/Regions for use for the Intel Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Page 17: Wireless Lan Card
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 18 11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the IEEE 802.11n specification.
Page 19: Bluetooth Wireless Technology Interoperability
Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/ bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for...
Page 20: Bluetooth Wireless Technology And Your Health
Approved Countries/Regions for use (Bluetooth technology) ® Bluetooth Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Australia Bulgaria...
Page 21: Regulatory Statements
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 22 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
Page 23 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850...
Page 24 (Sample shown below. Location of the label and manufacturing information may vary.) Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 25 EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING. TOSHIBA ASSUMES NO LIABILITY FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY FROM ANY TECHNICAL OR TYPOGRAPHICAL ERRORS OR OMISSIONS CONTAINED HEREIN OR FOR DISCREPANCIES BETWEEN THE PRODUCT AND THE MANUAL.
Page 26 Card is a trademark of Fuji Photo Film, Co., Ltd. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
Page 27: Table Of Contents
Keeping yourself comfortable ...39 Precautions...39 Important information on your computer’s Setting up your computer ...41 Setting up your software...41 Registering your computer with Toshiba ...42 Adding optional external devices...42 Connecting to a power source ...43 Charging the main battery...45 cooling fan ...40...
Page 28 Contents Using the computer for the first time ...46 Opening the display panel ...46 Your computer’s features and specifications ...47 Turning on the power...47 Adding memory (optional) ...48 Installing a memory module ...48 Removing a memory module...53 Checking total memory ...55 Hard Drive Recovery Utilities ...56 Creating Recovery CDs/DVDs ...57 Hard Disk Drive Recovery options ...58...
Page 29 Playing optical media ...98 Creating a CD/DVD...98 Removing a disc with the computer on...99 Removing a disc with the computer off ...99 Caring for CD or DVD discs ...100 Toshiba’s online resources ...100 keyboard ...85 ® keys ...86 Search field ...90 Contents ®...
Page 30 Contents Chapter 3: Mobile Computing...101 Toshiba’s energy-saver design...101 Running the computer on battery power ...101 Battery Notice ...102 Power management ...103 Using additional batteries ...103 Charging batteries...103 Charging the main battery...104 Charging the RTC battery...104 Monitoring main battery power...105 Determining remaining battery power...107 What to do when the main battery runs low ...107...
Page 31 Optimize...141 Setting passwords ...142 Using an instant password...142 Using a supervisor password...143 Using a user password ...144 Deleting a user password...145 TOSHIBA PC Diagnostic Tool Utility...146 Mouse Utility...147 Toshiba Hardware Setup...148 TOSHIBA Zooming Utility...150 TOSHIBA Button Support...151 from, the Internet...128 ®...
Page 32 Wireless networking problems...180 DVD operating problems...182 Develop good computing habits ...184 Data and system configuration backup in If you need further assistance...189 Before you contact Toshiba ...189 Contacting Toshiba ...189 ® operating system is not working ..162 ® operating system can help you ...164...
Page 33 Other Toshiba Internet Web sites...190 Toshiba’s worldwide offices...190 Appendix A: Hot Keys/TOSHIBA Cards ... 192 Hot Key Cards ...192 Using the Hot Key Cards ...193 Application Cards...194 Using the Application Cards...195 Card Case...195 Hot key functions ...196 Volume Mute ...197 Password security ...198...
Page 34: Introduction
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. NOTE This notebook is compatible with European Union Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE.
Page 35: This Guide
Toshiba’ s Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/component/options availability are all subject to change without notice.
Page 36: Safety Icons
Introduction Safety icons Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 37: Other Documentation
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see Goes Wrong” on page Introduction Other documentation 158.
Page 38: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
Page 39: Keeping Yourself Comfortable
Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals. Keeping yourself comfortable The Toshiba Instruction Manual for Safety and Comfort, included with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day.
Page 40: Important Information On Your Computer's Cooling Fan
Getting Started Selecting a place to work ❖ Never turn off the computer if a drive light indicates a drive is active. Turning off the computer while it is reading from or writing to a disk/disc or flash media may damage the disk/disc or flash media, the drive, or both.
Page 41: Setting Up Your Computer
Setting up your computer TECHNICAL NOTE: You must complete all setup steps up to and including external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards. Your computer contains a rechargeable main battery that needs to be charged before you can use it.
Page 42: Registering Your Computer With Toshiba
If you decide not to register at that time, you can either double-click the Toshiba Registration icon on your desktop or go to the Toshiba Web site at www.register.toshiba.com Product Registration will not diminish Customer rights under the Toshiba limited Warranty.
Page 43: Connecting To A Power Source
TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer possibly resulting in serious injury.
Page 44 Getting Started Connecting to a power source To connect AC power to the computer: Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 45: Charging The Main Battery
The computer’s main battery light gives you an indication of the main battery’s current charge: ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows blue when the main battery is fully charged ❖ Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet ❖...
Page 46: Using The Computer For The First Time
Getting Started Using the computer for the first time NOTE Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel Facing the front of the computer, locate the center of the display panel.
Page 47: Your Computer's Features And Specifications
Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
Page 48: Adding Memory (Optional)
NOTE Before adding external devices or memory, Toshiba recommends setting up your software. See Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer.
Page 49 If the computer has been running recently, the memory module may be hot. The surrounding area may also be hot. Allow the module to cool to room temperature before replacing it. Avoid touching the cover, the module, and the surrounding area before they have cooled. Failure to follow these directions could result in minor bodily injury.
Page 50 Getting Started Adding memory (optional) Click Shut Down. The operating system turns off the computer. Unplug and remove any cables connected to the computer, including the AC adaptor. Remove the main battery. For information on removing the main battery, see on page 111.
Page 51 Place the screw and the cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. Avoid touching the connector on the memory module or on the computer.
Page 52 Getting Started Adding memory (optional) Firmly press the memory module into the memory slot’s socket at approximately a 30-degree angle (to the horizontal surface of the computer). (Sample Illustration) Inserting the memory module into the socket Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket.
Page 53: Removing A Memory Module
Slot B (Sample Illustration) Inserting the memory module into the slot NOTE For this model Slot A is the bottom slot. Slot B is the top slot.If only one memory module is to be installed, it must be installed in slot A. Replace the memory module slot cover and secure it using the screw.
Page 54 Getting Started Adding memory (optional) Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module. Do not remove the memory module while the computer is in Sleep or Hibernation mode.
Page 55: Checking Total Memory
Gently lift the memory module to a 30-degree angle and slide it out of the slot. Memory slots (Sample Illustration) Removing the memory module Replace the memory module slot cover and secure it using the screw. Re-insert the main battery. For more information on inserting the main battery, see Turn the computer right side up.
Page 56: Hard Drive Recovery Utilities
Getting Started Hard Drive Recovery Utilities NOTE From time to time, Windows “Windows feature to prevent programs or people from doing things on your computer without your permission. If you were trying to perform the action, click Continue; otherwise, click Cancel. If unsure, cancel and try again.
Page 57: Creating Recovery Cds/Dvds
The system will prompt you to insert the appropriate number of blank CDs or DVDs to copy the Hard Drive Recovery Utilities. If your optical disc drive is not writable, contact Toshiba Customer Support to obtain the Recovery media for your system.
Page 58: Hard Disk Drive Recovery Options
Getting Started Hard Drive Recovery Utilities Select the items you want to copy by clicking the check box next to the item’s Name—recovery files, applications (original bundled drivers and applications), or both the recovery files and applications. Click Create. Insert the first blank CD or DVD into your writable optical drive when prompted.
Page 59 Press and hold the powering on the computer. When the computer powers on, the Toshiba Recovery Wizard screen displays. (Sample Image) Toshiba Recovery Wizard screen Select one of the options, and then click Next. The options are: ❖ Recovery of Factory Default Software ❖...
Page 60 Be sure to save your work to external media first. On the Toshiba Recovery Wizard screen, select Recovery of Factory Default Software, and then click Next. The Recovery of Factory Default Software screen appears.
Page 61 The Recovery Wizard allows you to delete all data and partitions from the hard disk. To delete the data and partitions from your hard disk: On the Toshiba Recovery Wizard screen, select Erase the hard disk, and then click Next. The next screen lists the two methods you can choose: ❖...
Page 62 To recover only your C: drive: On the Toshiba Recovery Wizard Screen, select Recovery of Factory Default Software, and then click Next. Select Recover without changing the hard drive partitions.
Page 63: Hard Disk Drive Recovery Using The Recovery Media
When the initial screen displays, press The boot menu appears. Using the arrow keys, select the CD/DVD option and press Enter . The system will boot up to the Toshiba Recovery Wizard screen. Please refer to page 58, to explain the available recovery options.
Page 64: Installing Drivers And Applications
Installing drivers and applications (Available on certain models) The TOSHIBA Application Installer (available on certain models) allows you to reinstall the drivers and applications that were originally bundled with your computer. To reinstall drivers and applications:...
Page 65: Scrolling With The Touchpad
NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons.
Page 66: Directing The Display Output When You Turn On The Computer
Getting Started Using external display devices Before connecting an external monitor or video projector, configure your computer for the type of device you are connecting. To do this, refer to the documentation for your operating system and devices. Connecting an external monitor or projector You can easily attach an external monitor or projector to your computer if you need a larger screen.
Page 67: Adjusting The Quality Of The External Display
❖ Built-in display and external monitor (extended desktop) ❖ Built-in display and TV (extended desktop) ❖ Swap—Switch primary display between internal display and external monitor when using extended desktop (Sample Image) Display options window Release the Adjusting the quality of the external display To obtain the best picture quality from your television (or other video display device), you may need to adjust the video settings.
Page 68: Connecting A Printer
Getting Started Connecting a printer Connecting a printer NOTE Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly.
Page 69: Connecting An Optional External Diskette Drive
Connecting an optional external diskette drive Click Start, Control Panel, Hardware and Sound, and then under Printers, click Add a printer. The Add Printer Wizard appears. (Sample Image) Add Printer Wizard Follow the on-screen instructions to set up your printer. Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5-inch diskettes.
Page 70: Turning Off The Computer
Getting Started Turning off the computer To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports. (Sample Illustration) Connecting an optional external USB diskette drive Turning off the computer Pressing the power button before shutting down the Windows operating system could cause you to lose your work.
Page 71 TECHNICAL NOTE: Before using the Shut Down option to turn off your computer, save your files and make sure all disk/disc activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. ❖...
Page 72 Getting Started Turning off the computer Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so that, when you restart the computer, you can continue working from where you left off.
Page 73: Using The Shut Down Command
Using the Shut Down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer. Use the following steps to turn off your computer using the Shut Down command: Click Start, and then click the arrow next to the Lock button in...
Page 74 Getting Started Turning off the computer Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen Click Power buttons and lid to display the actions that you can configure.
Page 75: Using And Configuring Hibernation Mode
Click Apply. Click OK. Once the computer is configured, you can turn it off by either pressing the power button or closing the display panel, depending on the options set. Restarting your computer To start the computer up again, press the power button until the on/off light glows blue.
Page 76 Getting Started Turning off the computer Configuring Hibernation mode options You can place the computer into Hibernation mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically goes into Hibernation mode.
Page 77 Select Hibernate for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power. ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
Page 78: Using And Configuring Sleep Mode
Getting Started Turning off the computer Using and configuring Sleep mode To turn off the computer using the Sleep command: Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu. The Shut Down menu appears.
Page 79 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. (Sample Image) Edit Plan Settings screen To change the amount of time after which the computer enters Sleep mode: ❖ Under Put the computer to sleep, select the desired amount of time in both the On battery and Plugged in categories.
Page 80: Closing The Display Panel
Getting Started Turning off the computer Click Power buttons and lid to display the actions that you can configure. Select Sleep for the options you want. NOTE These options can be set separately for how they operate while the computer is running on battery power or while connected to AC power.
Page 81: Customizing Your Computer's Settings
Customizing your computer’s settings There are several ways in which you can customize your computer to suit your particular requirements. Refer to your operating system documentation or Help and Support for details. You may also wish to customize your power usage settings. For more information, see additional custom settings you can choose.
Page 82: Using A Computer Lock
You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com. (Sample Illustration) Computer lock cable To secure the computer: Wrap the cable through or around some part of a heavy object.
Page 83: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 84 Learning the Basics Computing tips ❖ Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put off backing up because it takes time. However, if your hard disk suddenly fails, you will lose all the data on it unless you have a separate backup copy.
Page 85: Using The Keyboard
Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows functionality of a full-size keyboard. (Sample Illustration) Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖...
Page 86: Ctrl, Fn, And Alt Keys
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys (Sample Illustration) Ctrl, Fn, and Alt keys Ctrl , and program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the keys at the top of the keyboard.
Page 87: Overlay Keys
Overlay keys The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard. (Sample Illustration) Numeric and cursor control overlay Using the overlay to type numeric data The keys with the numbers on their right front are the numeric...
Page 88: Starting A Program
Learning the Basics Starting a program Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use the Start menu or Windows If you prefer to open the program first, you have four options.
Page 89: Starting A Program From Windows
Starting a program from Windows If a program is not listed in the All Programs menu, you can start it from Windows your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
Page 90: Starting A Program Using The Start Search Field
Learning the Basics Saving your work Starting a program using the Start Search field This example uses the Start menu’s Start Search field to start WordPad: Click Start to display the Start menu. The Start Search field appears at the bottom of the Start menu. Start Search field...
Page 91 Saving files ® In your Windows Click Browse folders. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box. Use this dialog box to specify where to store the document and to give it a file name.
Page 92: Printing Your Work
Learning the Basics Printing your work Using a file extension Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For example, Microsoft file name with an extension of “.doc” is assumed to be a Microsoft Word file.
Page 93: Backing Up Your Work
Specify the print parameters. For example, the range of pages and number of copies to print. Click Print. Backing up your work Back up all the files you create in case something happens to your computer. You can back up your files to different types of media such as CDs, DVDs, diskettes, or to a network, if available.
Page 94: Optical Drive Components
For optimum DVD performance, it is recommended that you play DVDs while running the computer on AC power. NOTE When viewing DVD movies use Toshiba DVD Player. Optical drive components The optical drive is located on the side of the computer.
Page 95: Media Control Buttons
Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. Media control buttons (Available on certain models) The media control buttons located above the keyboard let you access the Internet when the computer is on and play audio CDs or DVD movies.
Page 96 Learning the Basics Using the optical drive Grasp the tray and pull it fully open. (Sample Illustration) Drive tray fully extended Hold the disc by its edges and check that it is free of dust. If the disc is dusty, clean it as described in DVD discs”...
Page 97: Playing An Audio Cd
If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 98: Playing Optical Media
Learning the Basics Using the optical drive The Windows Media ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button. ❖ To stop the CD, click the Stop button. Before putting on headphones to listen, turn the volume down. Do not set the volume too high when using headphones.
Page 99: Removing A Disc With The Computer On
Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your Toshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or optical media recorders.
Page 100: Caring For Cd Or Dvd Discs
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions and keep you up to date with future upgrades.
Page 101: Chapter 3: Mobile Computing
Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency.
Page 102: Battery Notice
This is normal for all batteries. To purchase a new battery pack, see the accessories information included with your computer or visit the Toshiba Web site at accessories.toshiba.com. Use only batteries designed to work with your Toshiba notebook computer.
Page 103: Power Management
Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Always use the battery charger specified by Toshiba. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com.
Page 104: Charging The Main Battery
Mobile Computing Charging batteries Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Page 105: Monitoring Main Battery Power
NOTE The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adaptor is charging the computer. The RTC battery charges when the computer is powered on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working.
Page 106 Mobile Computing Monitoring main battery power NOTE If the AC power light flashes amber during charging, either a battery pack is malfunctioning, or it is not receiving correct input from the AC power supply. Disconnect the AC power cord/cable and remove the battery pack. “Changing the main battery”...
Page 107: Determining Remaining Battery Power
Determining remaining battery power Wait at least 16 seconds after turning on the computer before trying NOTE to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. Highlight the power icon in the Notification Area. A pop-up message displays the remaining battery power as a percentage.
Page 108: Setting Battery Notifications
Mobile Computing Monitoring main battery power Setting battery notifications You can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set the computer to enter Sleep mode or Hibernation mode or to completely power down when the notification goes off.
Page 109: Power Plans
❖ How much you use the hard disk, optical drive, diskette drives, or other optional devices ❖ Where you are working, since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖...
Page 110: Using A Hot Key To Set The Power Plan
Mobile Computing Monitoring main battery power Select an appropriate plan for your work environment or create your own custom plan. Click Create a Power Plan to set up a new plan. To edit a plan or to edit advanced settings, continue to the following NOTE steps.
Page 111: Changing The Main Battery
While continuing to press desired Power Plan. The Power Plan options are: Balanced, Power Saver, and High Performance. Release the The hot key card disappears. You are now in the selected mode. Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery.
Page 112 Mobile Computing Changing the main battery Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
Page 113: Inserting A Charged Battery
Inserting a charged battery To insert a battery: Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. Insert the charged battery into the slot until the latch clicks. The battery pack has been designed so that you cannot install it with reverse polarity.
Page 114: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 115: Maintaining Your Battery
Maintaining your battery Fully discharging your battery pack will allow better accuracy of the battery meter. To fully discharge your battery pack: ❖ Periodically, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges.
Page 116: Disposing Of Used Batteries
If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle™, a program of the Rechargeable Battery Recycling...
Page 117: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cords, and compact discs.
Page 118: Chapter 4: Exploring Your Computer's Features
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the ® Windows operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 119: Finding Your Way Around The Desktop
Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. Icons Start button (Sample Image) Windows Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 120 Exploring Your Computer’s Features Exploring the desktop Your desktop may contain other icons depending on your configuration. See Windows information on each icon and how to use it. Start button You use the Start button to: ❖ Start programs ❖ Open documents ❖...
Page 121: Setting Up For Communications
Setting up for communications To connect to the Internet or use an online service, you need: ❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet ❖ A way to connect to the ISP (for example modem/ ®...
Page 122: Connecting A Modem To A Telephone Line
Send a fax directly from your computer For more detailed information regarding your computer’s modem, visit Toshiba’s Web site at accessories.toshiba.com. Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line.
Page 123: Connecting Your Computer To A Network
Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack NOTE Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX).
Page 124 Exploring Your Computer’s Features Setting up for communications Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To set up a dial-up connection, use the Connect to the Internet Wizard: Click Start, Control Panel, Network and Internet, and then Connect to the Internet.
Page 125: An Overview Of Using The Internet
Using Wireless LAN connectivity NOTE Wireless connectivity and some features may require you to purchase additional software, external hardware or services. Availability of public wireless LAN access points may be limited. Your system may come with an optional wireless LAN module. This is a technology that expands wireless communication beyond networking equipment, and can connect many different kinds of electronic devices without the need for cables.
Page 126: The World Wide Web
Exploring Your Computer’s Features An overview of using the Internet The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet—a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP).
Page 127: Surfing The Internet
Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address. The Web address, or Uniform Resource Locator (URL), is a unique identifier for that computer system linked to the Internet.
Page 128: Uploading To, And Downloading Files From, The Internet
Exploring Your Computer’s Features Exploring audio features Uploading to, and downloading files from, the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer).
Page 129: Using External Speakers Or Headphones
Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers. Before putting on headphones to listen, turn the volume down. Do not set the volume too high when using headphones.
Page 130: Using Pc Cards
Exploring Your Computer’s Features Using PC Cards Using PC Cards (Available on certain models) TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with your computer, but are likely to be much more difficult to set up and use.
Page 131: Removing A Pc Card
Removing a PC Card Be sure to disable the PC Card prior to removing it. Otherwise, the system may be damaged. NOTE Before removing a PC Card, make sure that no applications or system services are using the card. Prepare the card for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove.
Page 132: Using An Expresscard
Exploring Your Computer’s Features Using an ExpressCard™ Using an ExpressCard (Available on certain models) The ExpressCard slot also supports hot swapping, which allows you to replace one ExpressCard with another while the computer is on. Inserting an ExpressCard Before you insert an ExpressCard comes with the card to see if you need to do anything before you insert it.
Page 133: Using The Bridge Media Adapter Slot
PDAs, digital cameras, digital video camcorders, etc. The Bridge Media Adapter slot may also support other types of media. For a complete list of supported media, visit Toshiba’s Web site at accessories.toshiba.com. NOTE Do not use the Copy Disk function for this type of media.
Page 134: Removing Memory Media
Exploring Your Computer’s Features Using the Bridge Media Adapter Slot Push the media into the adapter until it locks in place. (Sample Illustration) Inserting memory media When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Page 135: Using The I.link ® Port
Exploring Your Computer’s Features ® Using the i.LINK port ® Using the i.LINK port ® The i.LINK port on the side of the computer provides an extremely fast data transfer rate. ® In addition to high speed, the i.LINK port also supports isochronous data transfer (the delivery of data at a guaranteed rate).
Page 136: Chapter 5: Utilities
These utilities are described in this chapter. ❖ TOSHIBA Assist ❖ Supervisor password ❖ User password ❖ TOSHIBA PC Diagnostic Tool Utility ❖ Mouse Utility ❖ Toshiba Hardware Setup ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Button Support ❖...
Page 137: Toshiba Assist
TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, do one of the following: ❖ Double-click the TOSHIBA Assist shortcut icon on the desktop.
Page 138: Connect
Utilities TOSHIBA Assist Connect The features available in this category are: ❖ ConfigFree™ ❖ Bluetooth ❖ Bluetooth (Sample Image) TOSHIBA Assist window – Connect tab Connectivity Doctor ® Settings ® Local COM Settings...
Page 139: Secure
Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab Utilities TOSHIBA Assist...
Page 140: Protect & Fix
Utilities TOSHIBA Assist Protect & Fix The feature available in this category is: ❖ TOSHIBA PC Diagnostic Tool Utility (Sample Image) TOSHIBA Assist window – Protect & Fix tab...
Page 141: Optimize
The features available in this category are: ❖ Mouse Utility ❖ Toshiba Hardware Setup ❖ TOSHIBA Zooming Utility ❖ TOSHIBA Button Support ❖ CD/DVD Drive Acoustic Silencer ❖ TOSHIBA Accessibility (Sample Image) TOSHIBA Assist window – Optimize tab Utilities TOSHIBA Assist...
Page 142: Setting Passwords
When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of passwords on your computer: ❖ An instant password—Secures your open programs and files when leaving the computer temporarily.
Page 143: Using A Supervisor Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your computer.
Page 144: Using A User Password
Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access your...
Page 145: Deleting A User Password
To register a password for the power-on password functions: Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Password Utility. The TOSHIBA Password Utility window appears. (Sample Image) TOSHIBA Password Utility window Click Set. Enter your password, and then enter it again to verify.
Page 146: Toshiba Pc Diagnostic Tool Utility
Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool utility may show tests for features you do not have. This is normal and does not indicate a problem. To use the TOSHIBA PC Diagnostic Tool utility:...
Page 147: Mouse Utility
To access the Mouse utility: Click Start, Control Panel, and then Mouse under Hardware and Sound, or click the Mouse icon in the Optimize tab of TOSHIBA The Mouse Properties screen appears. (Sample Image) Mouse Properties screen The settings you can change are divided into these categories: ❖...
Page 148: Toshiba Hardware Setup
Windows ❖ Click Start, All Programs, Toshiba, Utilities, and then HWSetup, or click the Toshiba Hardware Setup icon in the Optimize tab of The Toshiba Hardware Setup screen appears. (Sample Image) Toshiba Hardware Setup screen – General tab...
Page 149 By changing any of the options that appear in the dialog boxes and clicking Apply, you can reconfigure that function. Any options that you change will become default settings when you restart your system. Toshiba Hardware Setup key. function key and access the wake-on keyboard Utilities...
Page 150: Toshiba Zooming Utility
Acrobat ❖ Icons on the desktop To access the TOSHIBA Zooming Utility: Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Zooming Utility. The TOSHIBA Zooming Utility Properties screen appears. (Sample Image) TOSHIBA Zooming Utility Properties screen Select the desired option(s).
Page 151: Toshiba Button Support
To zoom in, hold down the down the key and press For more information about how to use the TOSHIBA Zooming utility, right-click the click Help. Click OK. TOSHIBA Button Support TOSHIBA Button Support allows you to customize the Internet and CD/DVD buttons.
Page 152: Cd/Dvd Drive Acoustic Silencer
Double-click the icon in the Notification Area, or click the CD/DVD Drive Acoustic Silencer icon in the Optimize tab of TOSHIBA The CD/DVD Drive Acoustic Silencer screen appears. Click Set Quiet Mode to make the drive run more slowly and quietly for listening to music or audio files on a CD.
Page 153: Toshiba Accessibility
TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the press it once, release it, and then press a function key to activate the hot key function.
Page 154: Configfree
ConfigFree. ❖ Double-click the ConfigFree icon ❖ Press the TOSHIBA Assist button (if applicable to your system) to open the TOSHIBA Assist, and then click the ConfigFree icon. ❖ Click the ConfigFree icon then click the desired utility. ® in this section are applicable only if is available on your system.
Page 155: Configfree Utilities
NOTE If your computer is not connected to a network, the ConfigFree icon in the Notification Area is displayed with an “X.” ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Page 156 Utilities ConfigFree™ Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree profiles are useful for easily switching network settings and devices.You can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally, for example, you can set up a profile to match that environment and connect to the network.
Page 157 Click Open Settings. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window Click Add to start the Create Profile Wizard. Utilities ConfigFree™...
Page 158: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 159: Problems When You Turn On The Computer
Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
Page 160 If Something Goes Wrong Problems when you turn on the computer If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source.
Page 161 Try turning the computer on again. If the computer starts normally, the AC adaptor may be defective and will need to be replaced (see the Toshiba Web site at accessories.toshiba.com). If the AC power light starts flashing, remove the battery, and continue with the steps below.
Page 162: The Windows Operating System Is Not Working
If Something Goes Wrong The Windows Verify that the AC adaptor is the correct unit for your computer model. The computer may not be able to start from an AC adaptor that is rated for less current (amperage) than the computer requires, even if the rated voltage is correct, and the plug fits correctly in the DC-IN socket.
Page 163: Internet Problems
The Windows ❖ Safe Mode with Command Prompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Known Good Configuration (advanced) ❖ Directory Services Restore Mode ❖ Debugging Mode ❖ Disable automatic restart on system failure ❖ Disable Driver Signature Enforcement ❖...
Page 164: The Windows Operating System Can Help You
Click one of the options listed in the window and then follow the on-screen instructions. You can connect to Support Online by clicking Microsoft Customer Support or by going to Toshiba support at pcsupport.toshiba.com. Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using Windows and Support to troubleshoot the problem first.
Page 165: Fixing A Problem With Device Manager
The device most recently connected to the system is the one most likely to be causing a conflict. Resolving conflicts There are several things you can do to resolve hardware conflicts: ❖ Get the most recent drivers from the manufacturer. ❖...
Page 166: Memory Problems
If Something Goes Wrong Resolving a hardware conflict ❖ The Resources tab, which lists resources assigned to the monitor, optional external optical drive, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources. ❖...
Page 167: Power And The Batteries
NOTE For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in slot A. Power and the batteries Your computer receives its power through the AC adaptor and power cord/cable or from the system batteries (battery, optional secondary battery, and real-time clock (RTC) battery).
Page 168: Keyboard Problems
After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries. To purchase a new battery pack, see your accessories information included with your computer, or visit the Toshiba Web site at accessories.toshiba.com.
Page 169: Display Problems
Nothing happens when you press the keys on the external keyboard. You may have plugged the external keyboard in while the computer was turned on. Using the computer’s TouchPad: Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu.
Page 170 If Something Goes Wrong Resolving a hardware conflict The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Personalize. This opens the Personalization window. Click Windows Color and Appearance to choose the colors for the screen.
Page 171: Disk Drive Problems
Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology.
Page 172 If Something Goes Wrong Resolving a hardware conflict You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors Click Start. Error-checking tests and repairs the disk. Your hard disk seems very slow. If you have been using your computer for a long time, your files may have become fragmented.
Page 173: Optical Drive Problems
Optical drive problems You cannot access a disc in the drive. If the optical drive is an external drive, make sure that the drive’s cable is properly connected to the computer. Make sure the tray that holds the CD or DVD is closed properly. Press gently until it clicks into place.
Page 174: Sound System Problems
If Something Goes Wrong Resolving a hardware conflict The disc will not come out of the drive when you click the eject button on the screen. Press the button on the optical drive itself. For additional information see does not slide out.” on page Sound system problems No sound is coming from the computer’s speakers.
Page 175 ❖ Occasionally a defective PC Card slips through quality control. If another computer with a PC Card slot is available, try the card in that machine. If the card malfunctions again, it may be defective. Resolving PC Card problems Here are some common problems and their solutions: The slot appears to be dead.
Page 176: Expresscard™ Problems
If Something Goes Wrong Resolving a hardware conflict Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see mode” on page 71 The system does not recognize your PC Card.
Page 177 ❖ Occasionally a defective ExpressCard™ slips through quality control. If another computer with an ExpressCard slot is available, try the card in that machine. If the card malfunctions again, it may be defective. Resolving ExpressCard™ problems Here are some common problems and their solutions: The slot appears to be dead.
Page 178: Printer Problems
If Something Goes Wrong Resolving a hardware conflict Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see mode” on page 68 The system does not recognize your ExpressCard™.
Page 179: Modem Problems
The other system may be busy or off line. Try making a test transmission to someone else. For more information regarding your system’s V.92 modem, visit the Toshiba Web site at pcsupport.toshiba.com. If Something Goes Wrong Resolving a hardware conflict...
Page 180: Wireless Networking Problems
Wi-Fi will be lit). NOTE To determine if your computer has an internal Wi-Fi the device list in Device Manager (part of the Windows Panel, Hardware and Sound). Some Toshiba models may have a ® Wi-Fi ® Wi-Fi ❖...
Page 181 Click Details. Verify that the DHCP Enabled setting is set to Yes. Click Close. ❖ Use IPCONFIG to verify that the computer has a useful IP address—one other than the private address of 169.254.xxx.xxx assigned by Windows Click Start to open the Start menu. Type in the search field.
Page 182: Dvd Operating Problems
Verify that the disc is in a format that the drive supports. Ensure that the disc is properly inserted in the drive tray. Use Toshiba DVD Player to view DVD movies. ® operating system will now try to establish a operating system wireless management ®...
Page 183 “Checking device properties” on page 165 on using Device Manager to view the optical drive properties. Check the Toshiba Web site for new information on optical drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
Page 184: Develop Good Computing Habits
If Something Goes Wrong Develop good computing habits Develop good computing habits Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature.
Page 185: Data And System Configuration Backup In The Windows Operating System
Data and system configuration backup in the Windows system The Windows for backing up your Windows and other important files. Take advantage of these features to protect yourself from much more difficult and time-consuming restoration procedures, and to safeguard your valuable data from loss.
Page 186 DVDs, or hard drives. An external hard drive is recommended in case the internal hard drive fails. No additional software is required. Most of the CD and DVD drives built into recent Toshiba portable computer models can write to (or ‘burn’) as well as read from CDs.
Page 187 Follow these steps to back up your computer or files to CDs, DVDs, or a hard drive: NOTE You can not back up the computer while running on battery power. Connect the AC adaptor before continuing. Prepare your backup target by connecting it and/or inserting a blank CD or DVD in the drive.
Page 188 If Something Goes Wrong Develop good computing habits ❖ Have your factory Restore/Reconfiguration CD(s) on hand in case you need any files from them (available on certain models). ❖ Do not guess—follow directions carefully! It is often necessary to run an installation utility first—before connecting a new hardware item to the computer.
Page 189: If You Need Further Assistance
Go to the Tech Support Center, select your particular model from the list and go to the Detailed Specifications for that model. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. Contacting Toshiba If you still need help and suspect that the problem is hardware- related, Toshiba offers a variety of resources to help you.
Page 190: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred ❖ Exact error messages and when they occurred For technical support, call the Toshiba Global Support Centre: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 191 United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. If Something Goes Wrong Toshiba’s worldwide offices Japan Toshiba Corporation, PCO-IO 1-1, Shibaura 1-Chome...
Page 192: Appendix A: Hot Keys/Toshiba Cards
Appendix A Hot Keys/TOSHIBA Cards Hot keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to modify the following system functions: ❖...
Page 193: Using The Hot Key Cards
To use the Hot Key Cards using the pointing device: Move the cursor to the top center edge of the screen. The TOSHIBA Cards appear along the top of the screen. (Sample Image) Hot Key Card display Double-click the Card for the system function to be modified.
Page 194: Application Cards
154. Bluetooth settings This Application Card launches your Bluetooth settings. Disc Creator utility This Application Card launches the TOSHIBA Disc Creator utility. Toshiba Hardware Setup utility For more information, refer to Hardware Setup” on page TOSHIBA Button Support utility For more information, refer to Support”...
Page 195: Using The Application Cards
195). To use the Card Case: Move the cursor to the top center edge of the screen. The TOSHIBA Cards appear at the top of the screen. An icon appears momentarily in the top-right corner. Click the (Sample Image) Starting Card Case...
Page 196: Hot Key Functions
Hot Keys/TOSHIBA Cards Hot key functions The Card Case displays two rows of Cards. Cards that appear solid (not transparent) in the bottom row are enabled and can be selected when the Application Cards are displayed. The top row contains all of the disabled cards.
Page 197: Volume Mute
Volume Mute This TOSHIBA Card or hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Volume Mute options ❖...
Page 198: Password Security
Hot Keys/TOSHIBA Cards Hot key functions Password security This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Security options ❖ ❖ hot key function activates instant security. The user...
Page 199: Power Plan
Hot Keys/TOSHIBA Cards Hot key functions Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window.
Page 200: Sleep Mode
Hot Keys/TOSHIBA Cards Hot key functions Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see and configuring Sleep mode” on page Selecting this Card or pressing the hot key displays the...
Page 201: Hibernation Mode
Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page Selecting this Card or pressing the hot key displays the...
Page 202: Display Modes
Hot Keys/TOSHIBA Cards Hot key functions Display modes This TOSHIBA Card or hot key cycles through the power- on display options. The display modes are: ❖ ❖ ❖ ❖ ❖ ❖ ❖ ❖ To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Page 203: Display Brightness
Display brightness This TOSHIBA Card decreases or increases the screen brightness. This hot key decreases the screen brightness. This hot key increases the screen brightness. Selecting this Card or pressing either hot key displays the following options: (Sample Image) Display brightness Move the slider or press the appropriate hot key repeatedly to decrease or increase the display brightness.
Page 204: Disabling Or Enabling Wireless Devices
Hot Keys/TOSHIBA Cards Hot key functions Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The wireless mode is: ❖ Selecting this Card or pressing the hot key displays the...
Page 205: Disabling Or Enabling The Touchpad
Disabling or enabling the TouchPad This TOSHIBA Card or hot key enables/disables the TouchPad. For more information on using the TouchPad, see “Disabling or enabling the TouchPad™” on page Selecting this Card or pressing the hot key displays the following options: (Sample Image) Disable or Enable TouchPad options ❖...
Page 206: Changing Screen Resolution
Hot Keys/TOSHIBA Cards Hot key functions Changing screen resolution This TOSHIBA Card or hot key switches screen resolution. Selecting this Card or pressing the hot key displays the following options: [Space bar] (Sample Image) Screen resolution options Cycle through the screen resolutions, then select the desired...
Page 207: Keyboard Hot Key Functions
This hot key turns the numeric overlay on and off. This hot key turns the scroll lock feature on and off. This hot key turns the Zooming utility to zoom-out. This hot key turns the Zooming utility to zoom-in. Hot Keys/TOSHIBA Cards Hot key functions...
Page 208: Appendix B: Power Cord/Cable Connectors
Appendix B Power Cord/Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Page 209: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 DIMM alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 210 Glossary DSTN DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE LPT1 MIDI PCMCIA SCSI disk operating system dots per inch dual supertwist nematic digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission gigabyte hard disk drive...
Page 211 SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 212 Glossary baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) —...
Page 213 central processing unit (CPU) — The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character —...
Page 214 Glossary device — A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices. device driver — A program (called a “driver”) that permits a computer to communicate with a device.
Page 215 double-density diskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capacity of a high-density diskette). See also diskette, high-density diskette. download — (1) In communications, to receive a file from another computer through a modem or network. (2) To send font data from the computer to a printer.
Page 216 — The physical components of a computer system. Compare software. Hibernation — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 217 hot key — (1) A feature in which certain keys in combination with the key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. hot swapping —...
Page 218 Glossary local area network — See LAN. logical drive — A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
Page 219 non-system disk — A disk for storing programs and data that cannot be used to start the computer. Compare system disk. online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online Help, or to information coming from another company on a company network or the Internet.
Page 220 Glossary port — A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility.
Page 221 select — To highlight or otherwise specify text, data, or graphics with the intent to perform some operation on it. serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel.
Page 222 Glossary Web — See World Wide Web. ® Wi-Fi — A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) —...
Page 223: Index
167 notification 108 power plan 199 power plan hot key 110 real-time clock (RTC) 102 removing 111 BIOS Setup see Toshiba Hardware Setup Bridge Media Adapter inserting memory media 133 removing memory media 134 button power 48 start 120...
Page 224 Index communications network connection 123 set up 121 compact disc positioning 96 compact discs handling 96 inserting 95 removing 99 compact disk drive using 93 computer caring for 81 cleaning 81 moving 81 non-system disk or disk error message 161 not accessing disk drives 160 running on battery power 101 setting up 41...
Page 225 ExpressCard checklist 176 computer stops working 177 errors 178 hot swapping fails 177 not recognized 178 problem solving 176 ExpressCard™ inserting 132 removing 132 external monitor not working 170 mouse 67 external diskette drive connecting 69 external display, adjusting 67 FAT (File Allocation Table) 171 file extensions 92 file, backing up 84...
Page 226 Index keyboard character keys 85 function keys 86 hot keys 207 not working 160 overlay keys 87 special Windows® keys 86 troubleshooting 168 using 85 keyboard, external 67 keyboard, full-size 85 lock computer, using 82 main battery removing 111 memory adding 48 problem solving 166 removing expansion slot cover 50...
Page 227 165 computer hangs when ExpressCard inserted 177 computer hangs when PC Card inserted 175 computer will not power up 159 contacting Toshiba 189 corrupted/damaged data files 172 Device Manager 165 disk drive is slow 172 display is blank 169 ExpessCard...
Page 228 122 television adjusting display 67 Toshiba registering computer 42 worldwide offices 190 TOSHIBA Assist 137 Toshiba Hardware Setup 148 Toshiba online resources 100 traveling tips 117 troubleshooting DVD player general problems 182 external keyboard 168 keyboard 168...
Page 229 video projector adjusting display 67 warranty limited warranty 37 Web 126 Web Cam 129 Web sites 189 Wi-Fi® wireless networking 125 Windows Media® Player 97 Windows® Explorer 89 Windows® operating system Help and Support 164 problem solving 162 Windows® operating system desktop Windows®...

This manual is also suitable for:

M205-s3207 M205-s4804 M200-st2001 M205-s3217 M205-s4805 M205-s4806 ... Show all

Toshiba M200-ST2002 User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Computer's Features

Chapter 5: Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys/Toshiba Cards

Appendix B: Power Cord/Cable Connectors

Quick Links

Related Manuals for Toshiba M200-ST2002

Summary of Contents for Toshiba M200-ST2002