Page 1 If you need assistance: ❖ InTouch Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 219 in this guide. TOSHIBA ® P25 Series ® Center “If Something Goes Wrong” on C6654-0603M1...
Page 2 If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.
Page 3: Fcc Notice
Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used...
Page 4: Type Of Service
Irvine, CA 92618-1697 (949) 583-3000 Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. FCC Requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.
Page 5: If Problems Arise
FCC. In the event repairs are ever needed on your modem, they should be performed by Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba.
Page 6: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 7: Wireless Lan And Your Health
Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with...
Page 8 Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population;...
Page 9 België/ For outdoor usage only channel 10 (2457 MHz) and 11 (2462 MHz) is Belgique: allowed. For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 10 Caution: Exposure to Radio Frequency Radiation The Toshiba Wireless LAN Mini PCI Card will be installed with one of two types of antennas. The both of antenna types, when installed are located at the upper edge of the LCD screen.
Page 11 Refer to the Regulatory Statements as identified in the documentation that comes with those products for additional information. Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
Page 12: Device Authorization
This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 13: Interference Statement
❖ Consult the dealer or an experienced radio/TV technician for help. Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.
Page 14 Do not use this equipment except in the countries/regions in the following table. This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode. 802.11b (2.4GHz) Australia Canada France Ireland Luxembourg Norway Switzerland 802.11a (5GHz) Australia Canada...
Page 15: Wireless Lan Card
Mexico Norway Singapore Switzerland Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Page 16: Bluetooth Wireless Technology Interoperability
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for...
Page 17: Bluetooth Wireless Technology And Your Health
WirelessLAN. Please contact Toshiba PC product support on web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http:// www.pcsupport.global.toshiba.com in the United States for more information. Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy.
Page 18 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 19 Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’ s authority to operate the equipment. Taiwan Article 14 Unless approved, for any model accredited low power radio frequency...
Page 20 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 21 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. DVD-ROM, Multifunction drive safety instructions The DVD-ROM and Multifunction drives employ a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference.
Page 22 This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 23 DirectShow are registered trademarks, and Windows Media is a trademark of Microsoft Corporation. LapLink is a registered trademark of Traveling Software, Inc. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 24: Table Of Contents
Contents Introduction ...33 This guide ...33 Safety icons ...34 Other icons used...35 Other documentation ...35 Service options ...36 Chapter 1: Finding Your Way Around ...37 Making sure you have everything...37 Front with the display closed ...38 Back ...39 Right side...40 Left side ...41 Front with the display open...42 Front panel lights ...43...
Page 25 Keeping yourself comfortable ...48 Precautions...51 Setting up your computer ...53 Setting up your software...53 Registering your computer with Toshiba ...55 Adding external devices ...55 Connecting the AC adapter...56 Charging the main battery...58 Using the computer for the first time ...59 Opening the display panel ...59...
Page 26 Starting again after Shut down ...96 Using Hibernation ...97 Starting again from Hibernation mode ...98 Using Stand by ...99 Going into Stand by mode more quickly ...100 Starting again from Stand by ...100 Toshiba’s online resources ...100 ® special keys...77...
Page 27 Chapter 4: Mobile Computing ...101 Toshiba’s energy-saver design...101 Running the computer on battery power ...101 Power management ...102 Charging the battery ...103 Charging the RTC battery...104 Monitoring battery power ...105 Determining remaining battery power...105 Conserving battery power ...106 What to do when the battery runs low ...107 Setting battery alarms...108...
Page 28 Contents Lesson 8: Closing programs ...130 Lesson 9: Creating shortcuts ...130 Creating a shortcut to the Calculator...130 Creating a shortcut to the Character Map ...131 Lesson 10: Changing the screen saver...133 Lesson 11: Setting the date and time...135 Lesson 12: Removing objects from the desktop ...137 Lesson 13: Using System Restore ...139 Lesson 14: If I am lost, what do I do? ...140 Windows...
Page 29 Creating Your Music Library Using Adding Music from Your Hard Drive to Windows Playing Digital Music Files ...173 Finding Music Files in My Music ...174 Playing a Song ...175 Setting Up an Automatic Disc Jockey ...175 Finding and Playing an Album...176 Creating a Playlist ...176 Displaying Your Pictures...177 Viewing a Slide Show...179...
Page 30 Contents Connecting the modem to a telephone line ...202 Setting up a dial-up connection ...202 Exchanging data with another computer...203 Transferring files using a parallel Getting help transferring files...203 Connecting to the Internet ...203 An overview of using the Internet ...205 The Internet ...205 The World Wide Web ...205 Internet Service Providers...206...
Page 31 Modem problems...242 Develop good computing habits ...242 If you need further assistance...243 Before you call ...244 Contacting Toshiba ...244 Other Toshiba Internet Web sites ...245 Toshiba’s worldwide offices...245 Appendix A: Hot Keys...249 Instant password security...249 Without a password ...249 With a password ...249 Maintaining security when the battery isn’t fully...
Page 32 Contents Sound ...251 Power usage mode ...251 Stand by mode...252 Hibernation mode ...253 Display modes ...254 Display modes ...254 Enabling a wireless device ...255 Disabling or enabling the TouchPad ...255 Keyboard hot keys ...256 Appendix B: Power Cable Connectors... 257 Glossary ...
Page 33: Introduction
Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
Page 34: Safety Icons
Introduction Safety icons If you are new to computers, or have not used a notebook computer before, read through the first couple of chapters to familiarize yourself with the components of the computer and how to turn it on. After that, seek out whatever interests you most.
Page 35: Other Icons Used
Guides for other programs that may come preinstalled on your computer or that are available for installation on your Recovery CDs. ❖ For accessory information, visit Toshiba's web site at toshiba.com. ❖ The Microsoft documentation which explains the features of the operating system.
Page 36: Service Options
Introduction Service options Service options Toshiba offers a full line of service options built around its SelectServ visit Toshiba’s Web site at If you have a problem or need to contact Toshiba, see Something Goes Wrong” on page limited warranty programs. For more information, toshiba.com...
Page 37: Chapter 1: Finding Your Way Around
Chapter 1 Finding Your Way Around This chapter presents a “grand tour” of your notebook computer. It serves as a reference when you need to locate specific parts of the computer. Making sure you have everything Before doing anything else, consult the Quick Start card provided with your system to make sure you received everything.
Page 38: Front With The Display Closed
For more information on using the TV tuner, see Setup” on page Display latch CD/DVD control buttons *Functional only with optional Toshiba remote control “CD/DVD control buttons” on page 145. Remote IR port* Front panel lights Primary modular bay “Front panel...
Page 39: Back
Back Parallel port RGB (monitor) port USB ports LAN port The DC IN port is where you plug in the AC adapter for either operating the computer on external power or charging the battery. The RGB (monitor) port lets you connect an external monitor.
Page 40: Right Side
Finding Your Way Around Right side Right side ® i.LINK Port The modem port lets you use a standard RJ-11 telephone cable to connect the modem directly to a standard telephone line. For more information, see phone line” on page The two stacked PC Card slots support up to two Type I or Type II PC Cards, or one Type III PC Card.
Page 41: Left Side
Finding Your Way Around Left side Left side Microphone jack Headphone jack Line In jack Volume control Wireless antenna on/off switch* Security lock slot * functional only on systems with a wireless module installed The 3.5 mm headphone jack lets you connect stereo headphones or other audio-output devices, such as external speakers.
Page 42: Front With The Display Open
The power button turns the computer on and off. Holding down the power button for four seconds resets the computer. The Internet button launches your default Internet browser. The TOSHIBA Console button allows quick access to various functions. The One Touch TV Out button activates an external display device, such as a TV, when connected to the S-video port.
Page 43: Front Panel Lights
Finding Your Way Around Front with the display open The function keys, when used with the key, activate several different system functions. For more information, see “Hot Keys” on page 249. The front panel lights and system indicator lights provide information about various system functions.
Page 44: Indicator Lights
Finding Your Way Around Front with the display open the external power source is disconnected or if the battery is completely discharged. For more information on determining remaining battery power, see page 105. Indicator lights The hard disk drive light flashes while the hard disk drive is being accessed.
Page 45: Underside
white number printed on the key instead of typing the letter printed on the top of the key. For more information, see “Using the numeric keypad overlay” on page Never turn off the computer while any drive is in use. Doing so may damage the media and result in loss of data.
Page 46 Finding Your Way Around Underside The hard disk drive is the computer’s permanent data storage device. To prevent possible CPU overheating, do not block the cooling vents when the computer is in use. The battery pack contains the battery. For information about replacing the battery, see page 109.
Page 47: Chapter 2: Getting Started
Chapter 2 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
Page 48: Keeping Yourself Comfortable
AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact a Toshiba authorized service provider. Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers.
Page 49 ❖ If you are using an external monitor, the top of the display should be no higher than eye level. ❖ If you use a paper holder, set it at about the same height and distance as the screen. Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly.
Page 50 Getting Started Selecting a place to work ❖ Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores. ❖...
Page 51: Precautions
Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ❖...
Page 52 Getting Started Selecting a place to work ❖ Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation.
Page 53: Setting Up Your Computer
Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” on page 53 or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.
Page 54 Toshiba and Microsoft. Click Yes to register, or No to exit the process. If you click No, you may register with Toshiba by clicking the Register with Toshiba icon on the desktop. If you selected Yes in step 5, enter your personal information in the registration window.
Page 55: Registering Your Computer With Toshiba
Toshiba limited warranty worldwide at no charge to you. You can register your computer with Toshiba during the start-up process or by clicking on the icon on the desktop at a later time.
Page 56: Connecting The Ac Adapter
Power cable and AC adapter Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
Page 57 To connect AC power to the computer: Connect the power cable to the AC adapter. Connecting the power cable to the AC adapter Plug the AC adapter into the DC-IN on the back of the computer. Connecting the AC adapter to the computer Connect the power cable to a live electrical outlet.
Page 58: Charging The Main Battery
Getting Started Charging the main battery The AC power and battery lights glow. Damaged power cables can cause fire or electric shock. Never DANGER modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable. If the power cable becomes damaged or the plug overheats, discontinue use.
Page 59: Using The Computer For The First Time
Using the computer for the first time Opening the display panel Slide the display latch to the right and lift the display panel Opening the display panel To avoid damaging the display panel, don’t force it beyond the point where it moves easily. Never lift or move the computer using the display panel.
Page 60: Using The Touchpad
Getting Started Using the computer for the first time illustration to help you locate this button, see the display open” on page When you turn on the computer for the first time, don’t turn off the power again until the operating system has loaded completely.
Page 61: Control Buttons
❖ To move the cursor to the bottom of the page, drag your finger toward yourself. ❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left.
Page 62: Installing Additional Memory (Optional)
Getting Started Installing additional memory (optional) The Control Panel window appears. Click Printers and Other Hardware. Click Mouse or press the Fn + F9 hot keys. The Mouse Properties window appears. Click the TouchPAD ON/OFF tab. The TouchPAD ON/OFF tab view window appears. Select Disable or Enable, whichever is appropriate.
Page 63 Additional memory comes in various capacities (visit Toshiba’s website at There are two memory slots. Your system may have both slots occupied. If you use the computer for a long time, the memory modules will become hot.
Page 64 Getting Started Installing additional memory (optional) Memory slot cover Base of a Satellite P25 series computer Using a standard Phillips no. 1 screwdriver, unscrew the two screws that secure the expansion memory slot cover, then remove the memory slot cover. Removing the memory slot cover Put the screws and the cover in a safe place so that you can retrieve them later.
Page 65 Installing additional memory (optional) To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer). Remove the memory module from its antistatic packaging. Holding the memory module by its edges so that the gold connector bar faces the slot, fit the module into the socket.
Page 66: Removing A Memory Module
Getting Started Installing additional memory (optional) Turn the computer over and reconnect any cables you removed. Turn on the computer. To verify that the computer correctly recognizes the memory, click Start, Control Panel and click Performance and Maintenance. Click System to view the recognized memory.
Page 67: Connecting A Mouse
Connecting a mouse You may want to use a mouse instead of the TouchPad, the computer’s built-in pointing device. To connect a USB mouse, plug the mouse cable into one of the USB ports. Connecting a printer Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a local printer.
Page 68: Setting Up A Printer
Getting Started Setting up a printer You can connect a USB-compatible printer to your computer through the USB ports. To determine if the printer is USB- compatible, check its documentation. To achieve the connection, you need a suitable USB cable, which may come with your printer.
Page 69 the instructions indicated in your printer manual, or by using the operating system Add Printer Wizard. If you plan to set up a printer later, click Cancel. Using the Add Printer Wizard To set up a printer with the Add Printer Wizard: Click Start, Control Panel, then Printers and Other Hardware.
Page 70 Getting Started Setting up a printer Sample Add Printer Wizard Click Next. The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section.
Page 71: Turning Off The Computer
From the list of manufacturers and printers, select your printer, then click Next. Select the port settings according to the instructions in your printer’s documentation and the port to which your printer is connected, then click Next. The Add Printer Wizard prompts you to enter a printer name.
Page 72: Caring For Your Computer
Getting Started Caring for your computer computer off, it may take up to three hours to recharge the main battery. When you power down the computer, you have three options to choose from: Turn Off (or Shut down), Hibernate and Standby.
Page 73: Cleaning The Computer
You can purchase a carrying case from your Toshiba dealer or visit Toshiba’s Web site at Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Page 74 Getting Started Caring for your computer PORT-Noteworthy To secure the computer: Loop the cable through or around some part of a heavy object. Make sure there is no way for a potential thief to slip the cable off the object. Pass the locking end through the loop.
Page 75: Chapter 3: Learning The Basics
Chapter 3 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Page 76: Using The Keyboard
Learning the Basics Using the keyboard If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy. ❖ Use Error-Checking and Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level.
Page 77: Ctrl, Fn, And Alt Keys
❖ The lowercase l (el) and the number 1 are not interchangeable. ❖ The uppercase letter O and the number 0 are not interchangeable. ❖ Caps Lock case — the number and symbol keys are not affected. The caps lock light on the keyboard indicator panel illuminates when you press the Ctrl, Fn, and Alt keys Ctrl...
Page 78: Overlay Keys
Learning the Basics Using the keyboard The keyboard provides two keys that have special functions in the operating system: ❖ The Windows ❖ The Application key has the same function as the secondary TouchPad control button (or secondary mouse button). Overlay keys Keyboard overlay keys The keys with numbers and symbols on the front of them...
Page 79 You can still use the overlay keys to type alphabetic characters while the numeric overlay is on. To do so: ❖ For lowercase letters, hold down letters. ❖ For uppercase letters, hold down both you type the letters. To use the cursor control overlay when the numeric overlay is on, press and hold down keys.
Page 80: Starting A Program
Learning the Basics Starting a program Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer. If you prefer to open the program first, you have four options: ❖...
Page 81: Printing Your Work
HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. For information on how to name a file, see file system” on page Printing your work Verify that the Windows your printer as described in...
Page 82: Using The Dvd-Rom Or Multifunction Drive
Learning the Basics Using the DVD-ROM or Multifunction drive Click Start, then click My Computer. Click the drive that contains the file you want to copy. Double-click the folder that contains the file, then click the file you want to copy. HINT: You can use the Ctrl or Shift keys to select more than one file.
Page 83: Drive Components And Control Buttons
Using the DVD-ROM or Multifunction drive You use CD-ROMs to load and run software, and to access reference material such as catalogs, as well as listen to music. A special feature allows you to play audio CDs even when the computer is turned off.
Page 84: Cd/Dvd Control Buttons
Learning the Basics Using the DVD-ROM or Multifunction drive HINT: When the computer is off and the DVD-ROM drive is on, press the stop/eject control button on the top of the computer to eject a disc. CD/DVD control buttons The control buttons on the front edge of the computer let you to play audio CDs when the computer is off.
Page 85: Cd/Dvd Control And Digital Audio Modes
Using the DVD-ROM or Multifunction drive You can eject a disc by pressing the stop/eject button twice. Use this method to eject a disc when the computer is turned off and the sound subsystem is turned on. CD/DVD control and digital audio modes The following chart describes CD/DVD control and digital audio mode.
Page 86: Inserting A Disc
Learning the Basics Using the DVD-ROM or Multifunction drive Inserting a disc Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears. To turn the volume down, use the Volume Control switch or access the Volume Control program (click Start, All Programs, Accessories, Entertainment, Volume Control).
Page 87 Using the DVD-ROM or Multifunction drive Carefully place the disc in the empty tray with its label facing up. Inserting a disc Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction.
Page 88: Playing An Audio Cd
Learning the Basics Using the DVD-ROM or Multifunction drive Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray. Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked.
Page 89: Viewing The Contents Of A Cd Or Dvd
Using the DVD-ROM or Multifunction drive Rewind Play Stop Previous track Next track Mute Sample Windows Media The Windows Media an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖...
Page 90: Removing A Disc With The Computer On
Learning the Basics Using the DVD-ROM or Multifunction drive can use Explorer or My Computer to view the contents of any CD or DVD. Removing a disc with the computer on Never press the eject button or turn off the computer while the drive-in-use light is glowing.
Page 91: Caring For Cds And Dvds
An Internet Service Provider (ISP) To connect to the Internet, you need a Web browser, such as ® Microsoft For more detailed information regarding your computer’s modem, visit Toshiba’s web site at toshiba.com. Learning the Basics Setting up for communications Internet Explorer.
Page 92: Connecting The Modem To A Phone Line
Your computer comes with a built-in modem. To use the modem, you must connect it to a standard voice-grade RJ-11 telephone line. For more information regarding your computer’s modem, visit Toshiba’s web site at toshiba.com. Attach one end of a standard RJ-11 telephone cable to the modem port.
Page 93: Powering Down The Computer
Powering down the computer Pushing the power button before shutting down the Windows operating system could cause you to lose your work. Make sure the system indicator panel’s disk light and the drive-in- use light are off. If you turn off the power while a disk is being accessed, you may lose data or damage the disk and/or drive.
Page 94: Hibernation Command
Learning the Basics Using Shut down Holding the shift key while the Turn Off computer Windows dialog box is open, changes the Stand By button to Hibernate. For more information about setting up hibernation “Hibernation command” on page 94 on page Hibernation command The Hibernation command shuts the computer down completely, but it first saves the current state of the computer...
Page 95: Stand By Command
going into Hibernation mode more quickly, see Hibernation mode more quickly” on page Stand By command The Stand by puts the computer into a power-saving mode. Stand by holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off.
Page 96: Starting Again After Shut Down
Learning the Basics Using Shut down To use either of these methods, you first need to turn on the feature in the Toshiba Power Management Utility. Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon.
Page 97: Using Hibernation
Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Advanced tab, and select the options you want. ❖ When I press the power button...
Page 98: Starting Again From Hibernation Mode
When I close the lid Set this option to Hibernation for the computer to go into Hibernation mode when you close the display panel. Sample Toshiba Power Management Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button.
Page 99: Using Stand By
Using Stand by Follow these steps to power down the computer using the Stand by: Click Start, select Shut down computer. The Turn off computer box appears. Click Stand By. Sample Shut down computer dialog box The computer saves the status of all open programs and files to memory, turns off the display, and goes into a low-power mode.
Page 100: Going Into Stand By Mode More Quickly
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades.
Page 101: Chapter 4: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.
Page 102: Power Management
This is normal for all batteries. To purchase a new battery pack, see your accessories information that shipped with your computer, or visit the Toshiba Web site at: toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged.
Page 103: Charging The Battery
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s InTouch Center. Charging the battery Battery charge time may vary depending on the applications, power management settings, and features used.
Page 104: Charging The Rtc Battery
Mobile Computing Charging the battery Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity.
Page 105: Monitoring Battery Power
Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. The current power source and battery power remaining section displays the current charge state of the battery. The value displays as a percentage of remaining battery charge.
Page 106: Conserving Battery Power
Mobile Computing Monitoring battery power Click the Battery Power Meter tab. Sample Toshiba Power Management Battery Power Meter tab TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit.
Page 107: What To Do When The Battery Runs Low
Toshiba’s power-saving options greatly increase the length of time you can use the computer before it becomes necessary to recharge the battery. Toshiba has combined these options into preset power usage modes. What to do when the battery runs low When the battery runs low you can ❖...
Page 108: Setting Battery Alarms
To set an alarm: Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Alarm tab and set the alarm, as desired. Sample Toshiba Power Management Alarm tab...
Page 109: Changing The Main Battery
Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short- circuit its terminals. Removing the battery from the computer Save your work.
Page 110: Taking Care Of Your Battery
Mobile Computing Taking care of your battery While still holding the release latch in the open position, gently slide the battery pack out of the computer. Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Taking care of your battery...
Page 111: Maximizing Battery Life
Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through toshiba.com. ❖ Reverse Polarity should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity.
Page 112 Mobile Computing Taking care of your battery Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery light LED flashes or there is some other warning to indicate a low battery, go to step 4.
Page 113: Disposing Of Used Batteries Safely
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for Mobile Computing Disposing of used batteries safely 47, also apply while traveling.
Page 114 Mobile Computing Traveling tips manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information. TECHNICAL NOTE: When traveling by air, you may be required to pass your notebook through airport security equipment. The X-ray equipment will not harm your computer.
Page 115: Xp Operating System
Chapter 5 Getting to Know the Windows System This chapter introduces the Windows by guiding you through a few basic tasks. If you have used a Windows will find the Windows Whether you have used a Windows the skill and confidence you will gain from this chapter will more than offset the short amount of time spent going through these lessons.
Page 116: Lesson 1: Exploring The Desktop
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop Lesson 1: Exploring the desktop The desktop is the launching pad for everything you can do in the Windows start programs, find documents, set up system components, and perform most other computing tasks.
Page 117 The icons initially displayed on your system desktop include: Toshiba Access—Opens a window with links to software updates, services and support, and other important benefits. Recycle Bin—Holds files you’ve deleted using the Windows Explorer.
Page 118: Windows ® Xp File System
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop you open. You can use these buttons to quickly switch between the programs or windows. To make a program or window the active one, click the program’s or window’s button on the taskbar.
Page 119: Lesson 2: Using The Touchpad And Control Buttons Together
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together For more information, read the Microsoft documentation that comes with your computer. Lesson 2: Using the TouchPad and control buttons together The “Getting Started” chapter introduced you to the TouchPad, which is your basic tool for moving around the screen.
Page 120 Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Click an empty area to close the shortcut menu. Use the TouchPad to move the pointer to the Start button. Click Start, and select My Computer. The My Computer window appears.
Page 121: Lesson 3: Learning About The Internet
Getting to Know the Windows ® XP Operating System Sample desktop with the taskbar on the right HINT: You can move the taskbar to any of the desktop’s four edges. Click the taskbar once again and drag it back to the bottom of the desktop.
Page 122: Lesson 4: Creating A New Document
Getting to Know the Windows ® XP Operating System Lesson 4: Creating a new document you can also type a Web address in the My Computer window. Click Start, then double-click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click Address Bar if it is not checked.
Page 123 Getting to Know the Windows ® XP Operating System Lesson 4: Creating a new document The operating system creates an icon on the desktop called New Text Document with the icon name highlighted. To give your document a meaningful name, type and press Doc.txt Double-click the My New Doc icon.
Page 124: Lesson 5: Creating A New Folder
Getting to Know the Windows ® XP Operating System Lesson 5: Creating a new folder Lesson 5: Creating a new folder DEFINITION: A folder is an area where you can store documents and other types of files. It is analogous to a file folder stored in a file cabinet.
Page 125: Lesson 6: Starting Programs
Getting to Know the Windows ® XP Operating System Close the window by clicking its Close button and continue with the next lesson to learn how to start programs. Lesson 6: Starting programs Usually, you will know which program you want to use for a particular task.
Page 126 Getting to Know the Windows ® XP Operating System Lesson 6: Starting programs To open the second program, click Start, then click All Programs. Point to Accessories, then click Windows Explorer. The operating system opens Windows Explorer, which provides access to all your computer’s resources. For example, it lets you see all the files in a particular folder on the computer’s hard disk.
Page 127: Lesson 7: Resizing, Repositioning, And Hiding Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Lesson 7: Resizing, repositioning, and hiding windows If you have followed the lessons in this chapter, you now have a screen with several program windows open. You can organize these windows by resizing and repositioning windows so that you can see more than one of them at a time.
Page 128: Resizing And Moving Windows
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click the Minimize button at the top-right of the Explorer window to hide the window. Windows Explorer disappears from the desktop. However, it is still open, as you can see from the taskbar. HINT: Minimizing program windows is a good way to clean up the desktop without actually closing programs.
Page 129 Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click and drag the edge of the window until it takes up just less than half the width of the desktop. Click the title bar of the Paint window and drag it to the left side of the desktop.
Page 130: Lesson 8: Closing Programs
Getting to Know the Windows ® XP Operating System Lesson 8: Closing programs Lesson 8: Closing programs Once you are finished working with a document or program, it is a good idea to close it. While you can run several programs at the same time, having a large number of programs and documents open simultaneously can slow down your computer.
Page 131: Creating A Shortcut To The Character Map
Getting to Know the Windows ® XP Operating System Move the pointer to an empty area of the desktop, then click the secondary button. The operating system displays the desktop shortcut menu. Click New, then click Shortcut. The operating system displays the Create Shortcut dialog box.
Page 132 Getting to Know the Windows ® XP Operating System Lesson 9: Creating shortcuts Sample Search options on the Start menu Click All Files and Folders. The operating system displays the Search Results dialog box. Sample Search Results dialog box...
Page 133: Lesson 10: Changing The Screen Saver
Getting to Know the Windows ® XP Operating System HINT: Search also allows you to perform searches on the Internet. Type char and then click Search. The operating system displays a list of all the files with “char” in their names. Click the Character Map file with the secondary button and drag it to the desktop.
Page 134 Getting to Know the Windows ® XP Operating System Lesson 10: Changing the screen saver of these properties can be customized to meet your particular needs and tastes. DEFINITION: An object is an independent block of data, text, or graphics that was created by an individual application. This lesson introduces object properties by showing you how to change one of the properties of the desktop—the screen saver.
Page 135: Lesson 11: Setting The Date And Time
Getting to Know the Windows ® XP Operating System Click the arrow beside the current option to open the screen saver list box. Scroll through the screen saver options by clicking the scroll arrows in the list box. Try a screen saver pattern by clicking a name in the list box.
Page 136 Getting to Know the Windows ® XP Operating System Lesson 11: Setting the date and time Sample Date and Time Properties dialog box HINT: To open the Date and Time Properties dialog box more quickly, either click the time display on the taskbar with the secondary button, then click Adjust Date and Time, or double- click the time display.
Page 137: Lesson 12: Removing Objects From The Desktop
Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Lesson 12: Removing objects from the desktop Earlier in this tutorial, you created a new icon on the desktop. Since everything you have done to this point has been just practice, you may want to return the desktop back to its original uncluttered state.
Page 138 Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Sample Recycle Bin open on the desktop To completely remove an object, select it, and then click File, Delete. The object is permanently deleted from the Recycle Bin. Later on—in your real work, not in this tutorial—you will use the Recycle Bin to delete other objects such as folders, documents, and sometimes even programs.
Page 139: Lesson 13: Using System Restore
Getting to Know the Windows ® XP Operating System To delete everything from the Recycle Bin at once, choose Empty Recycle Bin from the File menu. Click Yes to confirm that you are sure. HINT: Empty the Recycle Bin periodically. Even though an item is moved to the Recycle Bin, it still uses valuable space on the hard disk drive until it is deleted from the Recycle Bin.
Page 140: Lesson 14: If I Am Lost, What Do I Do
Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? The operating system guides you through the process of storing your system settings for future use. It also guides you through restoring your system to the selected date or time. Lesson 14: If I am lost, what do I do? This lesson teaches you how to use some of the Help and Support features in Windows...
Page 141 Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? The left side of the screen contains the index. The text box above the index, where the cursor is flashing, lets you type in a topic you want to find in the index.
Page 142: Using The Online Tours And Tutorials
Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? program to look at it while you read about the program in the Help topic. Using the online tours and tutorials Whether you are new to computers or you have some experience, the Windows is a good place to start.
Page 143: Lesson 15: Turning Off Your Computer
Getting to Know the Windows ® XP Operating System Lesson 15: Turning off your computer It is very important that you let the Windows system shut down your computer. As it shuts down, the operating system performs a number of tasks that ensure that everything is in place the next time you turn on the computer.
Page 144: Chapter 6: Getting To Know The Windows Xp Media Center Edition
Chapter 6 Getting to Know the Windows Center Edition This section introduces you to the Windows Media Center Edition, a complete multimedia center where you can play your entire library of audio, video, and picture media on your computer, using either your computer’s keyboard, mouse, or the remote control.
Page 145: Media Center Setup
Getting to Know the Windows ® XP Media Center Edition Media Center Setup This section shows you how to set up your computer to use the Media Center. Connecting the Computer to a Television Your computer has TV-out capability, meaning you can connect it to a television and view the computer image on the television.
Page 146 Getting to Know the Windows ® XP Media Center Edition Media Center Setup If you have a cable TV set-top box, satellite, or other set-top box that controls your TV signal, connect the remote sensor control cable to the remote sensor and position the end of it over the remote receiver on your cable box.
Page 147 Getting to Know the Windows ® XP Media Center Edition Turn on the TV and select the TV IN video source (refer to your TV set reference manual as necessary). Select the signal source for TV in the Media Center program settings (refer to Settings”...
Page 148: Starting The Media Center
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Starting the Media Center To start the Media Center: ❖ Click Start, and then click Media Center, or point the remote control at the remote sensor and press the Start button.
Page 149 Getting to Know the Windows ® XP Media Center Edition Media Center Setup Wizard To complete the Media Center Setup, follow the wizard on- screen prompts. When the wizard finishes, the Media Center main window displays. You can run Media Center side by side with other Windows software programs.
Page 150 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Sample Media Center main window The Media Center main window is the central point for controlling all Media Center features. With a quick click of the mouse or using your remote control, you can: ❖...
Page 151 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Back Home screen Help Sample Title Bar Icons Use the Media Playback controls at the bottom of the screen to control your movies, music, and photo displays. Media Playback controls...
Page 152: Remote Control For Media Center
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Navigating Media Center In the Media Center windows, a selected item, such as a folder, file, or menu item is outlined with a green border. To select items, use the arrow buttons on the remote control, and then the OK button to enter your selection.
Page 153 Getting to Know the Windows ® XP Media Center Edition Remote Control Buttons Overview Play Record Replay Start Back Live TV My Music My Video Volume DVD Menu Clear The Remote Control The remote control has the following buttons/functions: Standby — Puts the computer into a power reduced standby state.
Page 154 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center FWD (Fast forward) — Moves media forward. Replay — Moves media backward (seven seconds for videos and live TV, one music track or one DVD chapter at a time). Pause —...
Page 155 Getting to Know the Windows ® XP Media Center Edition Channel/Page up (+) and down (-) — Changes the TV channel or moves a page up and down, depending on the available options. DVD Menu — Opens the main menu on a DVD movie, if available.
Page 156 Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Direct Access Buttons The direct access buttons open the main Media Center windows. ❖ TV opens the My TV window where you can watch and record TV and access other My TV features. ❖...
Page 157 Getting to Know the Windows ® XP Media Center Edition ❖ Moves a video forward. ❖ Moves a TV program (that has been paused or stopped) forward to the current moment in live TV, and then begins playing. Use REW to rewind selected video or picture media. Press REW again to increase the rewinding speed.
Page 158: Watching Television Programs
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs ❖ For videos and live TV and videos, Replay moves back 7 seconds. Using the Media Center Remote Control To begin using your remote control: Point the remote control at the remote sensor. The remote sensor should be located near your monitor or in a convenient place.
Page 159 Getting to Know the Windows ® XP Media Center Edition ❖ Quickly check which TV shows you have scheduled to record. ❖ Search for TV shows by title, keyword, or category. Sample MY TV screen To watch a television program: Press the TV button on the remote control.
Page 160: Watching Live Tv Using Time Shifting
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs Watching Live TV Using Time Shifting When you open the My TV window and begin watching live TV, Media Center begins recording the selected program in the background for up to 30 minutes. This allows you to use your remote control to stop, pause, rewind, and fast forward live TV programs within a 30- minute time range.
Page 161 Getting to Know the Windows ® XP Media Center Edition ❖ You can manually update the TV Guide in the Media Center Settings window at any time, even if you have automatic updates set up. ❖ If the TV Guide has not been downloaded from the Internet because there is no Internet connection, the message ‘No data available’...
Page 162: Watching A Recorded Tv Program
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs currently playing, the inset window will maximize and the program will play. Watching a Recorded TV Program Recorded TV is the storage place for all your recorded programs.
Page 163: Searching For A Tv Program
Getting to Know the Windows ® XP Media Center Edition the remote control. Select the option to change, and then press OK again. ❖ Select Recording errors to see which shows weren’t recorded and determine why they weren’t recorded. The show may have been in conflict with another show and then cancelled by Media Center, or it may have been a duplicate episode in a series.
Page 164: Recording Tv
Getting to Know the Windows ® XP Media Center Edition Recording TV Sample Searching for a TV program screen Recording TV The Media Center allows you to record TV programs for later viewing. You can record the show you are watching, or you can record another or future show or series from the Guide, the Search, or the Settings window in My TV.
Page 165: Recording Tv Tips
Getting to Know the Windows ® XP Media Center Edition If there is a recording conflict or error, the Record Conflict icon appears next to the show in the TV Guide. This means the show will not be recorded unless the conflict is resolved. Recording TV tips ❖...
Page 166: Recording From The Guide
Getting to Know the Windows ® XP Media Center Edition Recording TV Recording from the Guide To record a current or future show or series from the Guide: Press the Start button on the remote control, select My TV, and then select Guide. Use the arrow buttons on the remote control to find the show you want to record, select the show, and then press You can also press the numeric buttons on the remote...
Page 167: Recording Manually
Getting to Know the Windows ® XP Media Center Edition Use the arrow buttons to scroll through the search results to select the show you want to record, select the show, and then press OK. Select Record or Record Series in the window, and then press OK.
Page 168: Changing Your Settings
Getting to Know the Windows ® XP Media Center Edition Recording TV Select Record in the window, and then press OK on the remote control to set the recording and return to the Settings window. Press Back on the remote control to return to the Start menu.
Page 169: Changing Recording Priorities
Getting to Know the Windows ® XP Media Center Edition ❖ Recording a TV program, including manually recording ❖ The TV Guide ❖ The TV Signal ❖ Parental Control specifications ❖ DVD settings ❖ Audio settings To make a change, click on the desired setting. Changing recording priorities To enable the Media Center to resolve recording conflicts, you can specify how program recordings are handled.
Page 170: Listening To Music
Getting to Know the Windows ® XP Media Center Edition Listening to Music Press Back on the remote control to return to the previous window. Listening to Music The My Music window in the Media Center works with Windows Media Player to find and play your music files and CDs.
Page 171: Creating Your Music Library Using Windows Media Player
Getting to Know the Windows ® XP Media Center Edition Sample My Music screen Creating Your Music Library Using Windows Media Player Each time you add music files outside of Windows Media Player, you must use the Tools menu to add music files to your Windows Media Player Library for Media Center to find them.
Page 172: Adding Music From Your Hard Drive To Windows Media Player Library
Getting to Know the Windows ® XP Media Center Edition Listening to Music Click the Media Library tab to see where your new audio files have been placed. You can rename files by selecting the file and typing a new name or genre over the old one. The way you label your music files determines the category in which they are placed.
Page 173: Playing Digital Music Files
Getting to Know the Windows ® XP Media Center Edition Select Search to search all drives, or select Browse to search through a specific drive. Select the desired drive and then click OK. Windows Media Player searches the selected drives for all supported audio files and adds them to the Media Library.
Page 174: Finding Music Files In My Music
Getting to Know the Windows ® XP Media Center Edition Listening to Music Press the Start button on the remote control. Insert a CD into the CD drive — the CD plays automatically in Media Center. If you have other media such as live TV already playing when you insert the CD, Media Center asks you if you want to play the CD.
Page 175: Playing A Song
Getting to Know the Windows ® XP Media Center Edition Use the arrow keys to select a music file, and then press the Play button on the remote control to begin playing that music file. If you back up music files from a CD using Windows Media Player 9, you must log the files into the media player’s play list before you can play them using the Media Center.
Page 176: Finding And Playing An Album
Getting to Know the Windows ® XP Media Center Edition Listening to Music Use the arrow buttons to select Shuffle, and then press OK on the remote control. All songs in that genre are randomly played. Finding and Playing an Album In the Media Center Start menu, select My Music, and then select Albums.
Page 177: Displaying Your Pictures
Getting to Know the Windows ® XP Media Center Edition You can create a playlist that includes several tracks from various CDs or even a playlist that contains background music for a slide show. Use Windows Media Player to create playlists and then play them back using Media Center.
Page 178 Getting to Know the Windows ® XP Media Center Edition Displaying Your Pictures ❖ View and scroll through pictures that are in the My Pictures folder by using your remote control or your keyboard and mouse. Sample My Pictures screen After you organize your pictures in the My Pictures folder in Windows Explorer, open Media Center to view your pictures: Press the Start button on the remote control to open the...
Page 179: Viewing A Slide Show
Getting to Know the Windows ® XP Media Center Edition Viewing a Slide Show To view pictures as a slide show Press the Start button on the remote control to open the Media Center Start menu. Select My Pictures. Use the arrow buttons on the remote control to select the folder of pictures you want to view as a slide show, and then press OK.
Page 180: Organizing Your Videos
Getting to Know the Windows ® XP Media Center Edition Watching Your Digital Movies ❖ View your videos in full screen mode or from an inset window in Media Center. Sample My Videos screen Organizing Your Videos When you attach a digital video camera to your PC, Windows asks you how you want to capture your video.
Page 181: Playing Digital Videos
Getting to Know the Windows ® XP Media Center Edition If you want to share your videos with others, place them in the Shared Video folder. To do this, click Start on the taskbar, click My Documents, click the Shared Documents folder under Other Places, and then double-click the Shared Video folder.
Page 182: Sorting Videos
Getting to Know the Windows ® XP Media Center Edition Watching a DVD Use the arrow buttons to select the folder you want, and then press OK. Select the video file and press OK again. Your video plays in full screen mode. Press Back on the remote control to exit full screen mode and return to the previous window.
Page 183: Stopping A Dvd Movie
Getting to Know the Windows ® XP Media Center Edition To change the window size, move the mouse and click the Resize button on the taskbar of the DVD window. Sample Play DVD screen Stopping a DVD Movie Press the Stop button on the remote control to stop the movie.
Page 184: Playing A Dvd Movie Already In Your Drive
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Playing a DVD movie already in your drive If you already have a DVD movie in your drive, but you have been doing other things in Media Center or in other programs from your desktop, you can play the DVD by: Press the Start button on the remote control.
Page 185 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Administrator Controlled Settings Some settings apply to all Media Center windows for all users and must be set up by the administrator. These settings are: ❖...
Page 186 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings In the General window, do one of the following: ❖ Select About Media Center to find information about your version of Media Center. ❖ Select UI sounds to turn the sound on or off. Use the arrow buttons to select an option, and then press OK on the remote control.
Page 187 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Select TV/DVD. Select Recorder. ❖ Select Scheduled to check a list of scheduled recordings, delete scheduled recordings, resolve recording conflicts, and to change recording priorities for the programs you scheduled to record.
Page 188 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings About Recorded TV Storage Space Settings The space available for recording TV programs depends on your hard disk allocation, drive size, and default recording quality selections. Your PC requires a certain amount of space to run your Windows XP operating system, run software programs, and store data files.
Page 189 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings To change the TV Guide settings: In the Media Center Start menu, select Settings. You may need to select the scroll arrows on the Start menu to view Settings.
Page 190 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings In the TV Settings menu, select Parental control. The first time you select Parental control, Media Center asks you to create a password. Use the numeric keys on the remote control to enter your password.
Page 191 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Selecting Closed Captioning The audio settings window allows you to select closed captioning. Closed captioning displays the TV’s spoken audio in text format for those who are unable to hear the audio.
Page 192 Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Changing Picture Settings Each user can set his or her own picture settings. In the Media Center Start menu, select Settings. You may need to select the scroll arrows on the Start menu to view Settings.
Page 193: Chapter 7: Exploring Your Options
Chapter 7 Exploring Your Options In this chapter, you will explore other features of your notebook computer. ® Windows XP special features The Windows features and enhancements, including: ❖ New system file protection ❖ A system restore function, allowing you to rollback the system to its previous mode ❖...
Page 194: Personalizing Your Desktop
Exploring Your Options Personalizing your desktop Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work. You can customize the following aspects of the desktop: ❖ Taskbar—which resources to display for quick access ❖...
Page 195: Bringing The World To Your Desktop
Bringing the world to your desktop With the Windows your desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: Point to an empty space on the desktop and click the secondary button.
Page 196: Changing Desktop And Browsing Style
Exploring Your Options Personalizing your desktop To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. To select some other Web site, type the address of the Web site you want or click Browse to locate it.
Page 197: Personalizing Individual Windows
The My Computer window appears. Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box Click the preferred options. Click Apply, then OK. Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window.
Page 198: Customizing Window Toolbars
Exploring Your Options Personalizing your desktop Customizing window toolbars You can display one or more customizable toolbars at the top of a window. As you browse, the operating system detects the kind of information presented in the window and automatically displays the appropriate toolbar buttons and menus.
Page 199: Displaying Information About Each Folder
The elements you can add to the top of the window are: Toolbar element Address Bar Standard buttons Displays buttons for commonly used Displaying a toolbar in a window Click Start, then click My Computer. The My Computer window appears. On the View menu, point to Toolbars, then click the name of the toolbar you want to display.
Page 200: Using Your Computer At The Office
Exploring Your Options Using your computer at the office Open the folder you want to view as a Web page. In the Tools menu, select Folder Options. In the Tasks section, click the button for Show common tasks in folders. Click Apply, then OK.
Page 201: Setting Up For Communications
Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A modem (one comes with your computer) ❖ A telephone line ❖ A browser or communications program ❖...
Page 202: Connecting The Modem To A Telephone Line
Exploring Your Options Using your computer at the office To verify that the modem is set up properly, double-click the COM port to which your modem is connected. The Modem AMR Properties box appears. In the device status area, the computer should indicate whether the modem is working properly.
Page 203: Exchanging Data With Another Computer
Exchanging data with another computer To transfer a large amount of information between computers, you need a physical connection and a synchronization program. You can use the Windows synchronization program that transfers data using a cable connected to the computers’ parallel ports. Transferring files using a parallel port connection To transfer files using the computers’...
Page 204 Exploring Your Options Connecting to the Internet ❖ A telephone line, DSL, a cable connection, or a satellite link ❖ A browser or communications program ❖ An Internet Service Provider (ISP) Once you have established an ISP account, you can access the Internet.
Page 205: An Overview Of Using The Internet
An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Signing up with an Internet Service Provider ❖...
Page 206: Internet Service Providers
Exploring Your Options An overview of using the Internet Internet Service Providers To connect a computer directly to the Internet, many people and businesses use an Internet Service Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines necessary to maintain an Internet connection.
Page 207: Internet Features
Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive email of your own, you need a mailbox on the Web, or an email address. If you have an account with an ISP, you can probably set up an email address at the same time as you sign up for the service.
Page 208: Exploring Video Features
Exploring Your Options Exploring video features large amounts of data. You can also use the File Transfer Protocol (FTP) supported by a separate software program. Exploring video features Your computer’s video features provide the viewing of presentations or DVD movies on the computer screen. TECHNICAL NOTE: Video CD playback capability is not enabled on all systems.
Page 209: Display Settings Hot Key
Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply. The screen blinks momentarily while the settings are adjusted. The Monitor Settings window appears and asks if you want to keep the settings.
Page 210: Using A Microphone
Exploring Your Options Exploring audio features to the microphone jack and using the Sound Recorder feature in the operating system. DEFINITION: A .wav (pronounced “wave”) file is a format for storing sound in files. TECHNICAL NOTE: If you record MP3 files, you will only be able to play them on a device capable of playing MP3 files.
Page 211: Adjusting Recording Settings
When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button. To save the file, select Save from the File menu. Adjusting recording settings The better the quality of the recording, the more disk space the sound file requires.
Page 212: Connecting A Monitor, Keyboard And Mouse
Exploring Your Options Connecting a monitor, keyboard and mouse Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini-jack. Connecting a monitor, keyboard and mouse By connecting an external monitor, external full-size keyboard and a mouse, you can work with your notebook as if it were a standard office desktop computer.
Page 213: Removing A Module From The Modular Bay
Removing a module from the Modular Bay Use caution when lifting or turning your computer. Failure to do so may result in damage to components, such as cables, attached to your computer, or to the computer itself. Turn off the computer. You can also hot swap a module in the Modular Bay.
Page 214: Inserting A Module Into The Modular Bay
Exploring Your Options Using PC Cards Slide the module out of the computer. Sliding the module out Inserting a module into the Modular Bay To install a module into the Modular Bay, simply slide the module all the way into the Modular Bay. Using PC Cards PC Cards expand your computer’s capabilities and usefulness.
Page 215: Pc Card Supporting Software
Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later. Other cards may work with your computer, but are likely to be much more difficult to set up and use. PC Card supporting software PC Cards require Card and Socket Services software —...
Page 216: Removing Pc Cards
Exploring Your Options Using PC Cards Align the card connectors with an available PC Card slot and carefully slide the card into the slot until it locks into place. Inserting a PC Card If you have a Type III card, insert the connector into the lower slot.
Page 217: Hot Swapping
Remove the PC Card and store it properly. Removing a PC Card Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use.
Page 218 Exploring Your Options Using PC Cards Before removing a PC Card, stop it by clicking the Safely Remove Hardware icon on the System tray. Once the PC Card has stopped, you can safely remove it. See Cards” on page Never swap modules when the computer is in Hibernation or Standby mode.
Page 219: Chapter 8: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter. Your program stops responding.
Page 220 If Something Goes Wrong Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Windows Task Manager Applications tab Select the program you want to close, then click End Task.
Page 221 Windows Task Manager Shutdown menu, Turn Off option The computer shuts down. Your program performs an illegal operation. If you receive the message, “Your program has performed an illegal operation,” you should record the details of the message and consult the software manufacturer. To record the details: Click the Details button and select the text the operating system displays.
Page 222: Problems When You Turn On The Computer
If Something Goes Wrong Problems when you turn on the computer Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adapter and power cable properly or installed a charged battery.
Page 223: The Windows Operating System Is Not Working
The Windows The Windows working Once you are familiar with the desktop and used to the way the operating system responds to your work routine, you can easily detect if the operating system is not working correctly. For example: ❖ The operating system fails to start after the Starting Windows XP message appears.
Page 224: Internet Problems
If Something Goes Wrong The Windows ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configuration (your most recent settings that worked) ❖ Directory services restore mode (Windows controllers only) ❖ Debugging Mode ❖...
Page 225: The Windows Xp Operating System Can Help You
® The Windows XP operating system can help you If the operating system has started properly, but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. To access Windows Click Start, then click Help and Support. The Help and Support window appears.
Page 226: A Plan Of Action
If Something Goes Wrong Resolving a hardware conflict A plan of action The smooth operation of the system depends on the interaction of all devices, programs, and features. If the system or one of its attached devices isn’t working, resolving the problem can be time-consuming and frustrating.
Page 227: Fixing A Problem With Device Manager
theory, if every device connected to the computer is Plug and Play-compliant, no two devices will compete for the same system resources. Simply plug in the device and turn on your computer. The operating system automatically sets up your system to accommodate the new device. If you install an older (legacy) device that the operating system cannot recognize, the operating system may have difficulty assigning resources to it.
Page 228 If Something Goes Wrong Resolving a hardware conflict Disabling or enabling a device Click Start, click the My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. Click the Hardware tab. Click the Device Manager button. Select the specific device from the device category.
Page 229: Memory Card Problems
Click the Device Manager button. To view the device(s) installed, double-click the device type. To view the properties, double-click the device. The operating system displays the Device Properties dialog box, which provides an array of tabs. They include: ❖ The General tab, which provides basic information about the device.
Page 230: Power And The Batteries
If the error recurs without the memory module installed, the error is not caused by the memory module. Toshiba recommends using only memory approved by Toshiba. Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and optional secondary battery).
Page 231: Keyboard Problems
Let the battery discharge completely, then try charging it again. Check the power options using the Toshiba Power Management Utility. Have you added a device, such as a PC Card or memory module, that takes its power from the...
Page 232: Display Problems
If Something Goes Wrong Resolving a hardware conflict If the problem occurs when both the keypad overlays are off, make sure the software you are using is not remapping the keyboard. Refer to the software’s documentation and check that the program does not assign different meanings to any of the keys.
Page 233 ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Press Fn and F5 simultaneously to make sure the display priority is not set for the built-in screen. The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties.
Page 234: Disk Drive Problems
If Something Goes Wrong Resolving a hardware conflict Click OK. The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode.
Page 235 The drive’s properties box appears. Click on Properties. Click the Tools tab. Click the Check now button. The Check Disk box appears (for example, Check Disk You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors ❖...
Page 236: Dvd-Rom Or Multifunction Drive Problems
If Something Goes Wrong Resolving a hardware conflict DVD-ROM or multifunction drive problems You cannot access a disc in the drive. Make sure the drive tray has closed properly. Press gently until it clicks into place. Open the drive tray and remove the disc. Make sure the drive tray is clean.
Page 237: Sound System Problems
The color of the materials used to make the disc can affect its reliability. Silver-colored CD-ROMs are the most reliable, followed by gold-colored CD-ROM. Green-colored CD- ROMs are the least reliable. Sound system problems You do not hear any sound from the computer. Adjust the volume control.
Page 238 If Something Goes Wrong Resolving a hardware conflict Resource conflicts can cause problems when using PC Cards. “Resolving a hardware conflict” on page Card Information Structure When you insert a PC Card into a slot, the computer attempts to determine the type of card and the resources it requires by reading its Card Information Structure (CIS).
Page 239 available, try the card in that machine. If the card malfunctions again, it may be defective. Resolving PC Card problems Here are some common problems and their solutions: The slots appear to be dead. PC Cards that used to work no longer work.
Page 240 If Something Goes Wrong Resolving a hardware conflict Click Stop xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. Remove the card from the slot. Never swap modules when the computer is in Hibernation or Standby mode.
Page 241: Printer Problems
Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray.
Page 242: Modem Problems
If Something Goes Wrong Develop good computing habits Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack.
Page 243: If You Need Further Assistance
On a regular basis, back up the information stored on your hard disk. Here are some ways you can do this: ❖ Copy files to a CD or other media, following the steps in “Saving your work” on page ❖ Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape.
Page 244: Before You Call
GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. Contacting Toshiba...
Page 245: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred. ❖ Exact error messages and when they occurred. For technical support, call the Toshiba InTouch Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 246 If Something Goes Wrong Toshiba’s worldwide offices Belgium Toshiba Information Systems Benelux (Belgium) B.V. Excelsiorlaan 40 B-1930 Zaventem Belgium Czech Republic CHG Toshiba, s.r.o. Hnevkovskeho 65 61700 Brno Finland Scribona TPC OY Sinimäentie 14 P.O. Box 83 02630 ESPOO Finland...
Page 247 United States 800-457-7777 (within the US) 949-859-4276 (outside the US - this call may incur long distance charges) Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. Tel: 5249-6500...
Page 248 If Something Goes Wrong Toshiba’s worldwide offices Slovakia HTC a.s. Dobrovicova 8 81109 Bratislava Slovakia Spain Toshiba Information Systems (España) S.A. Parque Empresarial San Fernando Edificio Europa, 1a Planta Escalera A 28831 (Madrid) San Fernando de Henares Spain Switzerland Ozalid AG Herostrasse 7 8048 Zürich...
Page 249: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Instant password security Without a password The Fn + F1 key combination turns off the display and...
Page 250: Maintaining Security When The Battery Isn't Fully Charged
Hot Keys Instant password security the display’s content reappear. The Windows system log-on screen will appear, prompting you for a password. After typing in the password for the current user, press Enter. To activate the password feature: Click Start, Control Panel. Click Appearances and Themes.
Page 251: Sound
Sample power usage modes The power usage mode in the Windows under AC power is Full Power only. The properties of each mode are set in the Toshiba Power Management utility. This hot key cycles through the different alarm Hot Keys Sound ®...
Page 252: Stand By Mode
Hot Keys Stand by mode Stand by mode This hot key puts the computer into Stand by mode. Sample Stand by confirmation box ❖ A message box is displayed by default to confirm that the computer is going into Stand by mode. This message box can be set so it doesn’t display.
Page 253: Hibernation Mode
Hibernation mode This hot key puts the computer into Hibernation mode. Sample Hibernation confirmation box Hibernation mode ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it doesn’t display.
Page 254: Display Modes
Hot Keys Display modes Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window In o resolution of the internal display panel to match the resolution of the external display device. Display modes display mode options.
Page 255: Enabling A Wireless Device
Enabling a wireless device This hot key enables/disables the optional wireless devices in your computer (for systems with Wi-Fi The wireless modes are: Wi-Fi enabled—This enables the Wi-Fi module. Wi-Fi disabled—This disables the Wi-Fi module. Disabling or enabling the TouchPad This hot key enables/disables the TouchPad.
Page 256: Keyboard Hot Keys
Hot Keys Keyboard hot keys Keyboard hot keys and off. off. off. For more information, see This hot key turns the cursor control overlay on This hot key turns the numeric overlay on and This hot key turns the scroll lock feature on and “Overlay keys”...
Page 257: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Page 258: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory...
Page 259 direct memory access DIMM dual inline memory module disk operating system dots per inch DSTN dual supertwist nematic digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory enhanced capabilities port EPROM erasable programmable read-only memory file allocation table Federal Communications Commission fast infrared gigabyte...
Page 260 Glossary PCMCIA SCSI SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 261 alternating current (AC) — The type of power usually supplied to residential and commercial wall outlets. AC reverses its direction at regular intervals. Compare direct current (DC). application — A computer program that you use to perform tasks of a specific type.
Page 262 Glossary bus — An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus. bus speed —...
Page 263 compatibility — The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another. configuration — (1) The collection of components that make up a single computer system. (2) How parts of the system are set up (that is, configured).
Page 264 Glossary disable — To turn a computer option off. See also enable. disc — A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs. Compare disk. disk —...
Page 265 DVD-ROM (digital versatile [or video] disc read-only memory) — A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. emulation — A technique in which a device or program imitates another device or program.
Page 266 — The physical components of a computer system. Compare software. Hibernate — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 267 interlaced — A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device — See device. Internet — The decentralized, world-wide network of computers that provides electronic mail, the World Wide Web, and other services.
Page 268 Glossary megabyte (MB) — A unit of data equal to 1,048,576 bytes (1024 x 1024 bytes). See also bytes. memory — Typically refers to the computer’s main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM.
Page 269 NT file system (NTFS) — An advanced file system designed for use specifically with the Windows NT operating system. online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online help, or to information coming from another company on a company network or the Internet.
Page 270 Glossary processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility. See also operating system, application, utility. properties —...
Page 271 ROM (read-only memory) — Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up.
Page 272 Glossary universal serial bus (USB) — A serial bus that supports a data transfer rate of up to 12 Mbps (12 million bits per second). USB can connect up to 127 peripheral devices through a single all-purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial.
Page 273: Index
DVD-ROM or multifunction Internet 42 one-touch TV out 42 PC Card eject 40 power 42 Start 117 TOSHIBA Console 42 calculator 130 caps lock light 44 Card and Socket Services 215 CD and DVDs caring for 91 viewing contents 90...
Page 274 inserting 87 problem solving 236 channels DMA 226 Character Map 131 charging main battery 103 RTC (real-time clock) battery 104 checking device properties 228 cleaning CD or DVDs 91 computer 73 click 61 closing programs 130 comfort chair 49 lighting 50 work habits 51 commands Hibernate 94...
Page 275 Start button 117 system tray 118 taskbar 117 Device Manager 227 checking properties 228 disabling a device 228 dial-up connection 92 Dial-Up Networking Wizard 92 Digital Subscriber Lines (DSL) 204 disk activity light 44 Disk Defragmenter 235 disk drive corrupted/damaged data files 235 missing files/trouble accessing a disk 234 running slow 235...
Page 276 saving 75 transferring 203 Fn key 43 folders 118 displaying information 199 front panel 43 function keys 43 hard disk drive light 44 hardware conflicts 225 resolving 227 headphone jack 41 Help 140 Hibernate restarting 98 using 97 Hibernation 94 Hibernation mode 72 hiding windows 127 hot key...
Page 277 unexpected characters 231 Windows special keys 78 lights 44 AC power 60 battery 60 caps lock 44 cursor control mode 44 disk activity 44 DVD-ROM/multifunction drive hard disk drive 44 numeric mode 45 on/off 43 lock slot 41 main battery changing 109 removing 109 memory...
Page 278 233 checking device properties 228 compact discs not running computer hangs when PC Card computer will not power up 222 contacting Toshiba 244 corrupted/damaged data files 235 Device Manager 227 disabling a device 228 disk drive is slow 235...
Page 279 missing files/trouble accessing a disk 234 modem not receiving or transmitting 242 no sound 237 non-system disk or disk error 222 PC Card 237 checklist 238 error occurs 240 hot swapping fails 239 not recognized 240 slots appear dead 239 Plug and Play 227 power and batteries 230 printer 241...
Page 280 199 Toshiba Forum 244 Internet Web sites 245 online services 244 Toshiba Accessories information 35 TOSHIBA Console button 42 TouchPad 43 using 119 using with control buttons 119 transferring files 203 transferring information between computers 203...
Page 281 251 warranty SelectServ 36 Web address 206 Web browsers 205 Web content interface 195 Web sites 244 Web sites,Toshiba 245 windows hiding 127 repositioning 127 resizing 127 Windows Explorer 125 Windows Help 117 Windows Media Player 88...

This manual is also suitable for:

P25-s507 - satellite - pentium 4 2.8 ghz P25-s5263 - satellite - pentium 4 3 ghz Satellite p25 series

Toshiba P25-S607 User Manual

Chapter 1: Finding Your Way Around

Chapter 2: Getting Started

Chapter 3: Learning the Basics

Chapter 4: Mobile Computing

Chapter 5 : Getting to Know the Windows

Chapter 6: Getting to Know the Windows XP Media Center Edition

Chapter 7: Exploring Your Options

Chapter 8: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Quick Links

Related Manuals for Toshiba P25-S607

Summary of Contents for Toshiba P25-S607