Advertisement
Quick Links
5G Outdoor CPE N5368X
Quick Start
Part Number: 31071318
Version: Draft C
1
Tools
Before installing the CPE, verify that you have all the items listed in the packing list. If any of the
items is missing or damaged, contact your device provider.
1 x Outdoor-oriented mounting
bracket (including bolts)
1 x N5368X
2 x Hose clamp
You need to prepare the following tools and auxiliary materials:
Adjustable
M6 hex key
Screwdriver
wrench
2
Hardware Introduction
WiFi
5G
4G
1 x Indoor fixed-length
Ethernet cable
1 x Indoor-oriented
mounting bracket
1 x Waterproof
PG connector
1 x Quick Start
Rubber
Hammer
Ethernet cable
mallet
drill
RST
Nano SIM
LAN WiFi
Power/LAN
Running Status/Factory Reset Indication
The WiFi indicator, 5G indicator, and 4G indicators are on and off simultaneously.
Color
Status
WiFi
5G
4G
Green Green Green
Steady on
Blinking thrice (on for
Green Green Green
0.5s and off for 0.5s)
Blinking at 0.5 Hz (on
Yellow Yellow Yellow
for 1s and off for 1s)
Red
Red
Red
Steady on
Gray
Gray
Gray
Off
Upgrade Status Indication
Color
Status
Description
5G
4G
The device is restarted for an upgrade to load the new
Green Green
Steady on
version. The process is expected to take about 5 minutes.
· Before an upgrade (normal version verification and
Blinking(on for 0.2s
Green Green
decompression; upgrade in progress)
and off for 0.2s)
· After an upgrade (version verification)
When the upgrade is successful, the indicator blinks green
Blinking (on for 1s
Green Green
slowly thrice, and then the device starts up and enters the
and off for 1s)
network searching state.
Red
Red
Steady on
The upgrade fails.
LAN Port Status Indication
Color
Status
5G
4G
Blinking at 2 Hz
Red
Red
(on for 0.25s and off for 0.25s)
SIM Card Slot Status Indication
Color
Status
5G
4G
Blinking at 0.5 Hz
Red
Red
(on for 1s and off for 1s)
Description
·
The device is powered on and starting up.
·
The device is running properly. The hardware is
normal, and there is no software alarm.
The device is about to restore the factory settings and
restart.
The hardware component is normal and the network
searching state starts.
An exception in hardware component is detected.
The power is off or software configuration is disabled.
If the Wi-Fi hardware switch is turned off, the WiFi
indicator is off.
Description
The LAN port is not connected.
Description
The SIM card is not properly installed or is faulty.
Advertisement
Related Manuals for Huawei N5368X
Summary of Contents for Huawei N5368X
- Page 1 Running Status/Factory Reset Indication 5G Outdoor CPE N5368X The WiFi indicator, 5G indicator, and 4G indicators are on and off simultaneously. Color Quick Start Status Description WiFi · The device is powered on and starting up. Part Number: 31071318 Green Green Green Steady on ·...
-
Page 2: Indoor Installation
1.2 N•m Outdoor Installation NOTICE The N5368X can be installed outdoors on a pole or wall and must be within the 45-degree protection angle of the lightning rod. The WiFi switch must be off when the CPE is used outdoors. - Page 3 Ethernet cable into the LAN port in the N5368X maintenance cover. NOTE The LAN port of the N5368X is used only indoors. If this port is used outdoors, the waterproof Hang the four cucurbit holes on the metal plate at the rear of the N5368X onto the four function of the device may fail.
-
Page 4: Technical Specifications
N5368X. be forcibly logged out. · If the N5368X has not accessed the network, you need to manually enter the IP address on the IDU to configure and maintain the N5368X. Start the Internet Explorer, enter http://192.168.8.1... -
Page 5: Safety Precautions
EU Regulatory Conformance Statement · Keep the device away from electronic appliances that generate strong magnetic or electric fields, Hereby, Huawei Technologies Co., Ltd. declares that the radio equipment type is in compliance with such as a transformer, microwave oven, or refrigerator.