Related Manuals for Kenwood KDC-B7021
Summary of Contents for Kenwood KDC-B7021
- Page 1 KDC-V7521 KDC-B7021 KDC-7021 KDC-7021SE CD-RECEIVER INSTRUCTION MANUAL © B64-2591-00/00 (EF)
-
Page 2: Table Of Contents
Contents Safety precautions...3 About RDS ...5 About CDs...6 General features ...7 Power Volume Attenuator Selecting the Source Loudness System Q Audio Control Speaker Setting Switching Display Switching Clock Display Auxiliary Input Display Setting Faceplate Angle Adjustment Theft Deterrent Faceplate Hiding the Control Panel TEL Mute Tuner features ...12 Tuning... -
Page 3: Safety Precautions
KENWOOD disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any KENWOOD disc changers/ CD... - Page 4 Safety precautions NOTE • If you experience problems during installation, consult your Kenwood dealer. • If the unit fails to operate properly, press the Reset button. The unit returns to factory settings when the Reset button is pressed. After you press the reset button, the Mask Key will be needed to restart the unit.
-
Page 5: About Rds
The marking of products using lasers (Except for some areas) CLASS 1 LASER PRODUCT The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. -
Page 6: About Cds
About CDs Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. •... -
Page 7: General Features
General features u / d ATT / LOUD Clock indicator Speaker Setting indicator Power Turning ON the Power Turn the vehicle ignition ON. The faceplate reverses and control panel is displayed. Turning OFF the Power Turn the vehicle ignition OFF. When the set time for removing the faceplate (page 24) lapses, the faceplate reverses and the control panel is hidden. -
Page 8: Volume
General features Selecting the Source Press the [SRC] button. Source required Display Tuner "TUNER" "CD" External disc "DISC"/"CD2" Auxiliary input "AUX" Standby (Illumination only mode) "ALL OFF" • For Auxiliary input one of the below optional accessories is necessary. - KCA-S210A - CA-C1AX - CD changer with an Auxiliary input function installed. -
Page 9: Volume
Audio Control Select the source for adjustment Press the [SRC] button. Enter Audio Control mode Press the [AUD] button for at least 1 second. Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below. -
Page 10: Switching Display
General features Switching Display Switching the information displayed. Press the [DISP] button. Each time the button is pressed the display switches as shown below. In Tuner source Information Display Program Service name or Frequency Radio text "R-TEXT" Displaying the frequency during Program Service name reception Press the [DISP] button for at least 1 second. -
Page 11: Theft Deterrent Faceplate
Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Turn the ignition OFF or press the [SRC] button for at least 1 second. The power turns OFF and the faceplate slides open. Holding the center part of the faceplate pull it out. -
Page 12: Tuner Features
Tuner features #1 – 6 Band display Frequency display Tuning Selecting the station. Select tuner source Press the [SRC] button. Select the "TUNER" display. Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. -
Page 13: Station Preset Memory
Station Preset Memory Putting the station in the memory. Select the band Press the [FM] or [AM] button. Select the frequency to put in the memory Press the [4] or [¢] button. Put the frequency in the memory Press the [#1] — [#6] button for at least 2 seconds. The preset number display blinks 1 time. -
Page 14: Rds Features
RDS features #1 – 6 TI/VOL ADJ TI indicator PTY indicator Traffic Information Switching to traffic information automatically when a traffic bulletin starts even when you aren't listening to the radio. Press the [TI] button. Each time the button is pressed the Traffic Information function turns ON or OFF. -
Page 15: Pty (Program Type)
PTY (Program Type) Selecting the Program Type and searching for a station. Enter PTY mode Press the [PTY] button. During PTY mode the "PTY" indicator is ON. This function can't be used during a traffic bulletin or AM reception. Select the Program Type Press the [FM] or [AM] button. -
Page 16: Program Type Preset
RDS features Program Type preset Putting the Program Type in the Preset button memory and calling it up quickly. Presetting the Program Type Select the Program Type to preset Refer to <PTY(Program Type)> (page 15). Preset the Program Type Press the [#1] — [#6] button for at least 2 seconds. Calling up the preset Program Type Enter PTY mode Refer to <PTY(Program Type)>... -
Page 17: Cd/External Disc Control Features
CD/External disc control features SCAN RDM REP M.RDM Track number Playing CD When a CD isn't inserted Slide open the faceplate Press the [0] button. Insert a CD. 4 / ¢ DISP/NAME.S When a CD is inserted Press the [SRC] button. Select the "CD"... -
Page 18: Playing External Disc
Press the [SRC] button. Select the display for the disc player you want. Display examples: Display Disc player "CD2" CD player "DISC" CD changer/MD changer Pause and play Press the [38] button. Each time the button is pressed it pauses and plays. -
Page 19: Album Search
Do Album Search Press the [DISC+] or [DISC–] button. Canceling Direct Album Search Press the [38] button. Input "0" to select disc 10. Track/Album Repeat Replaying the track/disc you're listening to. Press the [REP] button. Each time the button is pressed the Repeat Play switches as shown below. -
Page 20: Disc Naming (Dnps
• When operation stops for 10 seconds the name at that time is registered, and Name Set mode closes. • Media that you can attach names to - Internal CD player: 30 discs. - External CD changer/ player: Varies according to the CD changer/ player. Refer to the CD changer/ player manual. -
Page 21: Menu System
DNPP (Disc Name Preset Play) (Function of Remote) Selecting the CD displayed in the DNPS of the CDs set in the Disc changer. Enter DNPP mode Press the [DNPP] button on the remote. When "DNPP" is displayed the DNPS display in order. Forward / Reverse display Press the [DISC–] or [DISC+] button. -
Page 22: Mask Key
Menu system Menu System Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. Enter Menu mode Press the [MENU] button for at least 1 second. "MENU"... -
Page 23: Touch Sensor Tone
Turn the power ON The vehicle engine turns ON. "TRANSMIT 1" is displayed. Enter the Mask Key's signal Repeat steps 4 and 5 abobe, and enter the Mask Key's signal. "APPROVED" is displayed. The unit can be used. Touch Sensor Tone Setting the operation check sound (beep sound) ON/OFF. -
Page 24: Illumination Color Setting
Menu system Function of the KDC-V7521 Illumination Color Setting You can set the display to a desired color. Select Illumination Color Setting Mode Press the [FM] or [AM] button. Select the "COL" display. The color continues to change gradually Continue pressing the [4] or [¢] button. Release your finger at the color you want. -
Page 25: System Q
power is turned OFF. The faceplate can be removed only during the set time period. Display and Setting "Off Wait 0s" "Off Wait 3s" (Original setting) "Off Wait 25s" System Q Setting display/don't display for the System Q factors (Bass center frequency, Bass Q factor, Bass extend, Middle center frequency, Middle Q factor, and Treble center frequency) in Audio control. -
Page 26: Auto Memory Entry
Menu system Local Seek <In Tuner mode> Only stations whose reception is good are searched for in auto seek tuning. Display Setting "Local.S OFF" The local seek function is OFF. "Local.S ON" The local seek function is ON. Tuning Mode <In Tuner mode> Sets the tuning mode. -
Page 27: Auto Tp Seek
Auto TP Seek When the TI function is ON and poor reception conditions are experienced when listening to a traffic information station, another traffic information station with better reception will be searched for automatically. Display Setting "ATPS ON" The Auto TP Seek Function is ON. "ATPS OFF"... -
Page 28: Basic Operations Of Remote
Basic Operations of remote – FM/AM/DISC /DISC [#0] — [#9] Loading and Replacing the battery Use one lithium battery (CR2025). Insert the batteries with the + and – poles aligned properly, following the illustration inside the case. 4/¢ 2WARNING Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. -
Page 29: In Tuner Source
In Tuner source [FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. [4]/ [¢] buttons Tune up or down band. [#0] — [#9] buttons Press buttons [#1] — [#6] to recall preset stations. [DIRECT] button Enters and cancels the <Direct Access Tuning>... -
Page 30: Accessories
2CAUTION ... Number of items • If your car is not prepared for this special connection-system, consult your KENWOOD dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug..1 •... -
Page 31: Connecting Cables To Terminals
Connector B — 31 — Front right output (Red) Front left output (White) Rear right output (Red) Rear left output (White) To KENWOOD disc changer/ DAB control input/ KPA-SD100/KPA-HD100/KPA-SS100 To connect these leads, refer to the relevant instruction manuals. To "EXT.AMP.CONT." terminal of the EXT.CONT. -
Page 32: Installtion
Connecting Cables to Terminals 2WARNING Connecting the ISO Connector (see p.31) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. -
Page 33: Removing The Unit
Removing the Unit Insert the removal tool into the indentations in the hard rubber frame, and pull it gently until the lock is released. Remove the screw (M4×8) on the back panel. Insert the two removal tools deeply into the slots on each side, as shown. -
Page 34: Troubleshooting Guide
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General The power does not turn ON.01 The fuse has blown. - Page 35 The sound quality is poor or distorted.25 One of the speaker wires is being pinched by a screw in the car. Check the speaker wiring. The speakers are not wired correctly.27 Reconnect the speaker wires so that each output terminal is connected to a different speaker.
- Page 36 Troubleshooting Guide Disc source "AUX" is displayed without achieving External disc control O-N switch is set to "O" side. Set the switch to "N" side. Unsupported disc changer is connected.51 Connect the supported disc changer. (page 3) The specified disc does not play, but another one plays The specified CD is quite dirty.
- Page 37 NO ACCESS: After setting it in the Disc Changer, DNPP was done without having it been played at least 1 time. IN (Blink): The CD player section is not operating properly. Reinsert the CD. If the CD cannot be ejected or the display continues to flash even when the CD has been properly reinserted, please switch off the power and consult your nearest service center.
-
Page 38: Specifications
Usable sensitivity (S/N = 20dB) ...25 µV LW tuner section Frequency range ...153 kHz – 281 kHz Usable sensitivity (S/N = 20dB) ...45 µV CD player section Laser diode ...GaAlAs (λ=780 nm) Digital filter (D/A)...8 Times Over Sampling D/A Converter ...1 Bit Spindle speed ...500 –...