Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: Please reaD these instrUCtions CarefUllY. note the safe oPerational reQUirements, warnings anD CaUtions.
Use the ProDUCt CorreCtlY anD with Care for the PUrPose for whiCh it is intenDeD. failUre to Do so maY CaUse Damage
anD/or Personal inJUrY anD will inValiDate the warrantY. Please keeP instrUCtions safe for fUtUre Use.
1. safetY instrUCtions
warning! Ensure Health and Safety, local authority and general
workshop practice regulations are adhered to when using tools.
Do not use tools if damaged.
Maintain tools in good and clean condition for best and safest
performance.
Ensure that a vehicle which has been jacked up is adequately
supported with axle stands.
Wear approved eye protection. A full range of personal safety
equipment is available from your Sealey dealer.
Wear suitable clothing to avoid snagging. Do not wear jewellery and
tie back long hair.
Account for all tools, locking bolts, pins and parts being used and do
not leave them in or near the engine.
warning! Incorrect or out of phase camshaft timing can result in
contact between valve head and piston crown causing damage to the
engine.
IMPORTANT: These instructions are provided as a guide only. Always
refer to the vehicle manufacturer's service instructions, or a proprietary
manual, to establish the current procedure and data.
WARNING: The warnings, cautions and instructions discussed in
this manual cannot cover all possible conditions and situations
that may occur. It must be understood that common sense and
caution are factors which cannot be built into this product, but
must be applied by the operator.
Instructions for:
Petrol engine twin Camshaft &
Diesel engine setting / loCking tool
kit
Vs4930
Model No:
2. introDUCtion / aPPliCations
The Ford 1.6 16v. Ti VCT Duratec (Sigma) petrol engine was first
introduced in the Ford Focus in 2004. The engine has variable camshaft
timing (VCT) on both the inlet and exhaust camshafts.
VS4930 Setting / Locking Tool Kit provides the timing tools required for
timing belt replacement applications PLUS to cover VCT timing
adjustment.
forD 1.6 ti-VCt twin Camshaft 16v. Duratec Petrol engine in
forD
Focus
C-Max
hXDa engines
Page 1 of 4
Mondeo
VS4930 Issue No:1 - 23/07/08
Advertisement
Related Manuals for Sealey VS4930
Summary of Contents for Sealey VS4930
- Page 1 Vs4930 Model No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: Please reaD these instrUCtions CarefUllY. note the safe oPerational reQUirements, warnings anD CaUtions.
- Page 2 4 ..VS4832 ..Flywheel Locking Tool 5 ..VS4933 ..Camshaft Setting Plate - ..VS4930/84 ..Case + Insert Fig.3 Fig.1...
- Page 3 If bore depth is 42mm. – use M12 x 29mm bolt If bore depth is 52mm. – use M12 x 44.5mm bolt. If the timing marks do not align, repeat the belt installation and tensioning procedures. Install the lower belt cover. Page 3 of 4 VS4930 Issue No:1 - 23/07/08...
- Page 4 For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. sole Uk Distributor 01284 757500 www.sealey.co.uk We b sealey group, 01284 703534 sales@sealey.co.uk Bury St. Edmunds, Suffolk. email...