Honeywell Performance Series Quick Installation Manual
Wdr 1080p ir bullet camera
Hide thumbs
Also See for Performance Series:
- User manual (276 pages) ,
- Owner's manual (22 pages) ,
- Installation instructions manual (16 pages)
Advertisement
Quick Links
HBW2PER1 WDR 1080P IR Bullet Camera
Quick Installation Guide
Thank you for purchasing a Honeywell Performance Series
IP camera. Follow the instructions in this guide to install and
log in to your camera. For instructions on configuring the
camera, refer to the user guide on the CD that came with
your camera. If you require additional assistance, call the
number listed for your region on the back cover.
Cautions and Warnings
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING
To ensure compliance with electrical safety standards, this product is
intended for use with a Listed Power Adapter marked "Limited Power
Source" or "LPS" on the unit, output rated to 12 VDC, minimum 0.33 A,
TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed
Information Technology Equipment meeting IEEE 802.3af PoE standard.
CAUTION
The Ethernet connection is not intended to be connected to exposed
(outside plant) networks. Do not connect two power sources to the camera
at the same time.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to beam.
Important Safeguards
•
Read and keep these instructions.
•
Confirm the installation surface can support at least three times the weight of the
camera.
•
Do not aim the camera toward a bright light source for extended periods to prevent
damage to the imager.
•
Avoid operating the unit under or close to unstable light sources (may cause flickering),
or close to fluorescent lamps or objects reflecting light.
THIS SYMBOL INDIC ATES THAT
DANGEROUS VOLTAGE
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
THIS SYMBOL INDIC ATES THAT
IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
•
Do not touch the camera lens.
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
•
Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments,
where the operating temperature is outside the recommended range of -22°F to 140°F
(–30°C to 60°C).
•
Do not apply power to the camera before completing installation.
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are
missing or damaged, contact your dealer immediately.
•
Camera
•
Installation CD
•
Quick installation guide
CAUTION
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
Preparing the Mounting Surface
1.
Apply the mounting template to the mounting surface.
Note Observe the orientation of the cable exit notch on the bracket base. In outdoor
installations, the notch should point downward to prevent water from entering the
camera housing.
2.
Using the mounting template as a guide, drill three pilot holes in the mounting surface,
then hammer the supplied anchors into the holes.
3.
Drill a cable entry hole in the mounting surface, then pull the required cables through the
hole.
Mounting and Aiming the Camera
1.
Connect one end of the Ethernet cable to the RJ-45
port on the camera.
2.
If the other end of the Ethernet cable is NOT
connected to a PoE switch or NVR, connect the
power connector of the camera to a 12 VDC power
source.
•
Self-tapping screws (×4)
•
Plastic wall anchors (×4)
•
Mounting template
Advertisement
Related Manuals for Honeywell Performance Series
Summary of Contents for Honeywell Performance Series
- Page 1 Do not apply power to the camera before completing installation. Before You Begin Thank you for purchasing a Honeywell Performance Series IP camera. Follow the instructions in this guide to install and log in to your camera. For instructions on configuring the Before you begin, check that you have received all of the parts listed below.
- Page 2 © 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell...