Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Warning:
instructions
Beware
crushing of
hands.
1. safety
WarNiNG! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this trolley.
‰
WarNiNG! be careful to ensure that when closing the sliding top you do not catch any part of your body between the runners.
‰
Always load evenly with the centre of gravity of the load as near centre of the trolley as possible.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
Keep the trolley clean and tidy in accordance with good workshop practice.
9
use the wheel locks to prevent the trolley from inadvertently moving.
9
Keep children and unauthorised persons away from the work area.
9
Do Not overload the trolley. max capacity 100kg.
8
Do Not use the trolley for any purpose other than that for which it is designed.
8
Do Not stand on the trolley, use it as a ladder or allow others to ride on the trolley.
8
Do Not leave unattended, especially when loaded, unless the wheels are locked, chocked or the trolley is otherwise secured.
8
Do Not use trolley on uneven ground and do not run over curbs or steps - use a ramp.
8
Do Not use trolley if any part is significantly damaged, paying particular attention to the wheels.
8
Do Not move trolley with draws out ensure they are closed and locked.
8
Do Not pull out more than one loaded drawer at any one time or tipping may occur.
8
Do Not overload drawers.
8
castors limited to 2.5 mph travelling speed.
8
Do Not tow unit.
8
Note! Do not force side drawers open, they will open only when the sliding top is open.
Note! The assembly will require assistance.
2.
iNtroDuctioN
Heavy gauge steel construction with lockable sliding top on smooth ball bearing runners. twin drawers with 35mm heavy-duty ball bearing
slides, which are locked when top is closed. Side handle for comfort and control when manoeuvring. Fitted with four wheels, two fixed and two
locking castors. suitable for tools and parts. some self-assembly required.
3. specificatioN
model no: ......................................AP705m.V2/AP705mB.V2
size (W x d x H):.....................................770 x 370 x 830mm
load capacity: .............................................................. 100kg
4. parts
© Jack sealey limited
instructions for
Mobile tool & parts trolley
model no:
unit may tip.
serious injury
close and lock
may occur.
drawers before
Do Not pull
moving.
unit.
use one drawer
Push to move.
at a time.
Do Not tow.
Original Language Version
ap705M series
caution:
Hang on cabinets:
remove items
caution. make sure
from work
cabinet is weighted
surface prior
down enough to counter
to closing lid.
balance the weight of
any side hanging unit.
failure to do
so will result in
make sure cabinet will
damage to lid.
not tip over if any loaded
draw is extended.
Do Not attempt to lift
cabinet using the lids
when loaded, only lift
this way when empty.
Before pulling out any
loaded drawer, make
sure unit is weighed
down enough to avoid
tipping.
AP705m.V2, AP705mB.V2| issue 1 06/04/16
Advertisement
Related Manuals for Sealey AP705M Series
Summary of Contents for Sealey AP705M Series
- Page 1 Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 5. asseMbly environmental protection recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)