Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
Keep this product in good working order and condition, take immediate action to repair or replace damaged parts.
Use approved parts only. Unapproved parts may be dangerous and will invalidate the warranty.
Keep children and unauthorised persons away from the work area.
Keep work area clean and tidy and free from unrelated materials.
Ensure the work area has adequate lighting.
DO NOT use the kit to perform a task for which it is not designed.
DO NOT allow untrained persons to use the kit.
DO NOT use when tired or under the influence of drugs, alcohol or intoxicating medication.
After use, clean equipment and store in a cool, dry, childproof area.
Dispose of waste liquids in accordance with local authority regulations.
Always read and comply with the warnings on the brake fluid container.
Wear eye protection and keep skin contact to a minimum. If brake fluid enters eyes rinse with plenty of water and seek medical advice. If
swallowed seek medical advice immediately.
WARNING! Only use new Brake Fluid, used Brake Fluid or other fluids will contaminate the system and possible brake system failure may
result.
WARNING! DO NOT pollute the environment by allowing uncontrolled discharge of fluids.
WARNING! Brake fluid is flammable - keep away from sources of ignition, including hot surfaces e.g. exhaust manifold.
WARNING! Brake fluid will damage paintwork. Any spillage should be flushed with water immediately.
WARNING! Do not allow the fluid capacity in the unit to fall below ½ litre during the bleeding process otherwise air may enter the
system.
2. INTRODUCTION
One-man pressure brake and clutch bleeding system suitable for the professional workshop. Low pressure tank (20-40psi) can be
pre-charged with compressed air - making the unit fully portable. Large reservoir means reduced risk of running the system dry during bleed-
ing process or complete fluid change. Suitable for use on ABS systems. Features a long delivery hose for operation with a low level ramp and
long reach handle for easy mobility. Supplied with Ø42mm cap with 90° angled connector which is suitable for most European models. For
other applications order optional Brake reservoir Cap 42mm Straight Connector - Model no. VS0204SA, Universal Adaptor - Model no.
VS820UA or Brake & clutch Bleeder Cap Set - Model no. VS0204B.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VS0204A
Air Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-40psi
Air consumption:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5cfm
Inlet size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4"BSP
Tank capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5.0 litres
Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7mtr
© Jack Sealey Limited
I
NSTRUCTIONS FOR:
BRAKE & CLUTCH PNEUMATIC
PRESSURE BLEEDER
VS0204A
MODEL No:
Fig.1
Original Language Version
VS0204A Issue: 1 - 05/05/16
Advertisement
Related Manuals for Sealey VS0204A
Summary of Contents for Sealey VS0204A
- Page 1 Model No: ........
- Page 2 (fig.4). 5.1.7. Connect the fluid supply pipe quick connector to the adaptor and slowly open the valve (fig.1.3) to pressurise the system. Original Language Version © Jack Sealey Limited VS0204A Issue: 1 - 05/05/16...
- Page 3 Brake & Clutch Bleeder Cap Set Model no. VS0204B Fig.7 Comprehensive set of brake and clutch reservoir bleed caps, supplied as standard with Model no. VS0204 and VS0207. Also compatible with Model no's VS820, VS821, VS0204A, offering a greater coverage of European, Japanese and US manufacturers. 6. MAINTENANCE 6.1.