Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instructions
1. SAFETY
WARNING! Ensure Health & Safety and local authority regulations are adhered to when using this equipment.
‰
Familiarise yourself with this product's application and limitations.
9
Maintain the AK9894 in good condition (use an authorised service agent). Replace or repair damaged parts. Use genuine parts only.
9
Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the AK9894 clean for the best and safest performance.
9
DO NOT exceed the rated capacity of the AK9894.
8
Suction lifters are hand tools and must not to be used with cranes or other lifting devices.
9
Before each use, make sure the suction pad is smooth, clean and undamaged.
9
Clean suction pad regularly with non-aggressive cleaners.
9
Make sure the surface of the object to be lifted is of non-porous material. In addition, the surface must be clean, dry and free of oils
9
and grease.
Use on clean, relatively smooth, non-porous surfaces; Moisture or contaminants can reduce the slip resistance of the cup.
9
On rough or porous surfaces, the holding capacity decreases or is non-existent.
9
DO NOT use sharp objects to loosen the suction cup from the surface as this will damage the suction pad.
8
Only use the suction lifter if you are experienced or under supervision by someone experienced in handling this tool.
9
Always test the functioning of the suction cup prior to its use. Examine handle for dents or cracks.
9
Examine rubber pad for excessive glaze, cuts or roughness.
9
Suction cup should only be used for lifting, carrying and holding objects for a short period of time. However, in the case of long periods
9
of attachment, check suction cup regularly to ensure firm adhesion. If grip does not feel sufficiently firm, re-apply suction cup.
Prior to use, always check the rubber pad for possible loss of suction capacity due to reduced elasticity caused by excessive age,
9
usage, etc. A rubber pad which is damaged or lacks sufficient suction capacity must be replaced. Never use suction cup with damaged
rubber pad or insufficient suction capacity.
DO NOT exceed stated lifting capacity of suction cup which is for 'Float glass' at room temperatures of 20°C. Cold temperatures,
8
humidity and pollution, carelessly treated or damaged suction pads, or usage on materials other than flat glass (such as structured
glass, plastics, stone, metal, etc.) may reduce the holding capacity considerably.
DO NOT use the cup to support a person.
8
DO NOT place the cup face against surfaces which could damage the sealing edges.
8
Avoid conditions that could cause the cup to slip or to disengage prematurely, such as: contaminants, cuts or scratches in the cup face
9
or mounting surface.
DO NOT allow anything to interfere with free movement of the plunger while the cup is attached.
8
DO NOT touch the rubber release tab or the valve release lever while lifting.
8
DO NOT use any solvents or other harsh chemicals to clean the cup. Store suction cup in a flat, relaxed position when not in use.
8
When not in use, store in a safe, dry, childproof area.
9
2. INTRODUCTION
Heavy lift capacity. Red-line indicator warns of any vacuum loss. Release valve lever for quick removal. Easy attachment on smooth, non-
porous, flat surfaces. Complete corrosion resistant finish. GS/TUV approved. Supplied in carry-case.
3. SPECIFICATION
Model no: ................................................................. AK9894
Cup Ø:........................................................................ 206mm
Maximum lift capacity: ................................. 80kg (horizontal)
© Jack Sealey Limited
INSTRUCTIONS FOR
HEAVY LIFT SUCTION CUP WITH VACUUM
GRIP INDICATOR GS/TUV APPROVED
AK9894
MODEL NO:
Original Language Version
AK9894 | Issue 4(L) 13/09/16
Advertisement
Related Manuals for Sealey AK9894
Summary of Contents for Sealey AK9894
- Page 1 AK9894 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group. 01284 757500 www.sealey.co.uk Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk. 01284 703534 sales@sealey.co.uk IP32 7AR Original Language Version © Jack Sealey Limited AK9894 | Issue 4(L) 13/09/16...