Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this equipment.
Familiarise yourself with the applications, limitations and potential hazards peculiar to the riveter.
p
WARNING! Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
3
Maintain the riveter in good condition (use an authorised service agent).
p
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
3
Keep the work area clean, uncluttered and ensure that there is adequate lighting.
3
Keep the riveter clean for best and safest performance.
3
WARNING! Always wear approved eye or face protection when operating the riveter.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
p
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain, and/or tie back, long hair.
3
Keep the riveter away from your body and at a safe distance from others.
3
Keep children and unauthorised persons away from the work area.
3
Secure unstable workpiece with a clamp, vice or other adequate holding device.
3
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
3
WARNING! Ensure that the correct air pressure is maintained and not exceeded.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
p
7 DO NOT use the riveter for any purpose other than that for which it is designed.
3
7 DO NOT use the riveter if the safety cap is not in place (see para. 4.4.).
7 DO NOT operate the riveter if any parts are damaged or missing and ensure that the safety cap (part 23) is correctly fitted.
7 DO NOT carry the riveter by the hose, or yank the hose from the air supply.
7 DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
7 DO NOT allow untrained persons to operate the riveter.
7 DO NOT point or fire the riveter at people or animals.
7 DO NOT operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT direct air from the air hose at yourself or others.
When not in use disconnect from the air supply and store in a safe, dry, childproof area.
3
2.
INTRODUCTION & SPECIFICATION
This heavy duty riveter is suitable for both aluminium and steel rivets up to 3/16” diameter. Supplied with
four riveting nozzles and two spanners. Trigger operated, with hardened steel jaw assembly and rivet
stem safety cap. The riveter is suitable for heavy assembly work.
Nozzle Sizes . . . . . . 3/32” (2.4mm), 1/8” (3.2mm)
5/32” (4.0mm), 3/16” (4.8mm)
Air Consumption . . . . . . . . . . . . . . . . . . . . 4.2cfm
Operating Pressure . . . . . . . . . . . . . . . . . . . 90psi
Air Inlet. . . . . . . . . . . . . . . . . . . . . . . . . . 1/4”BSP
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3kg
3.
AIR SUPPLY
The recommended air system is shown in fig. 2.
3.1.
Ensure that the trigger is in the "Off" position before connecting to the air supply.
3.2.
Ensure that the air pressure (90psi) is set correctly.
3.3.
p WARNING! Ensure that the air supply is clean and does not exceed 90psi. Too high an air pressure and/or unclean air will shorten
the life of the riveter due to accelerated wear, and may cause damage and/or personal injury.
3.4.
Drain the air tank daily. Water in the air line will damage the riveter.
3.5.
Clean the compressor air inlet filter screen weekly.
3.6.
Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose bore should
be 10mm and fittings must have the same inside dimensions.
3.7.
Keep hoses away from heat, oil and sharp edges.
Check hoses for wear, and make certain that
all connections are secure.
fig. 2
INSTRUCTIONS FOR:
AIR/HYDRAULIC RIVETER
SA31
Model:
fig. 1
SA31 - 1 - 211101
Advertisement
Related Manuals for Sealey SA31
Summary of Contents for Sealey SA31
- Page 1 SA31 Model: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 5.2. Lubricate the air tool daily with a high quality air tool oil (Sealey No. ATO/500 or ATO/1000) either via an oiler in the air supply system or by placing a few drops into the riveter air inlet immediately before use.