Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
polisher.
Familiarise yourself with the application, limitations and potential hazards of the polisher.
9
WARNING! Disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
‰
servicing or performing any maintenance.
Maintain the polisher in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! Keep all guards and holding screws in place, tight and in good working order.
‰
Check regularly for damaged parts. A guard or any other part that is damaged must be repaired/replaced before the polisher is next
9
used.
Use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. Ensure that there is
9
adequate lighting.
Keep the polisher clean for best and safest performance.
9
Before each use check all attachments for condition. If worn or damaged replace immediately.
9
Ensure that there are no flammable materials near the work area.
9
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
‰
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Avoid unintentional starting.
9
DO NOT use the polisher for any purpose other than that for which it is designed.
8
DO NOT operate the polisher if any parts are damaged or missing as this may cause failure and/or personal injury.
8
DO NOT switch the polisher on until the head is in contact with the panel and switch the unit off before removing the head from the
8
panel.
DO NOT use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
8
DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT allow untrained persons to operate the polisher.
8
DO NOT operate the polisher when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT use the polisher where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT leave the polisher operating unattended.
8
DO NOT carry the polisher with your finger on the power switch.
8
DO NOT pull the cord from the power supply.
8
Use a qualified person to maintain the polisher.
9
When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
9
2. INTRODUCTION
Digital display and variable speed control from 2100-5000rpm. 15mm Orbit for greater polishing efficiency. Features a slide button on/off
switch allowing for a smooth comfortable main handle grip. Spindle lock for fast and easy pad changes. Double injection composite housing
with rubber grip for added comfort. Requires Model No's CP20VBP, CP20VBP2 or CP20VBP4 20V Battery and Model No. CP20VMC Mains
Charger. Supplied with Ø125mm backing pad.
3. SPECIFICATION
Model No:..............................................................CP20VOP
Battery: ................................................. 20V 2Ah - 6Ah Li-ion
Free Speed: .................................................... 2100-5000rpm
Noise Power/Pressure: ........................................ 86/75dB(A)
Pad Size: ................................................................ Ø125mm
Vibration/Uncertainty: ......................................... 4.56/1.5m/s²
© Jack Sealey Limited
Ø125MM CORDLESS ORBITAL POLISHER 20V
- BODY ONLY
MODEL NO:
Wear protective
Wear protective
gloves
clothing
Original Language Version
CP20VOP
Wear ear
Wear a mask
protection
CP20VOP Issue 1 06/05/20
Advertisement
Related Manuals for Sealey CP20VOP
Summary of Contents for Sealey CP20VOP
- Page 1 CP20VOP MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 4.3. To select the required speed press the positive speed selector switch to the appropriate speed. 4.4. Contact your Sealey stockist for details of compound heads and polishing mop bonnets. 4.5. BACKING PAD EXCHANGE (FIG.2) WARNING: Remove battery before fitting / removing pads or maintenance is ‰...
- Page 3 BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.