Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
Wear ear
instruction
protection
manual
1. saFetY
warNiNG! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
warNiNG! disconnect from the air supply before changing accessories, servicing or performing any maintenance.
‰
maintain the tools in good condition (use an authorised service agent).
9
replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
maintain correct balance and footing. Do Not over reach, ensure the floor is not slippery and wear non-slip shoes.
9
warNiNG! Always wear approved eye and hand protection when operating these tools.
‰
use face, dust, or respiratory protection in accordance with cosHH regulations.
9
warNiNG! due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend that
‰
suitable respiratory protection is worn.
depending on the task, the tool noise level may exceed 84dB in which case wear safety ear defenders.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Keep children and unauthorised persons away from the work area.
9
ensure that the workpiece is secure before operating the tool. never hold a workpiece by hand.
9
Do Not operate tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
warNiNG! ensure correct air pressure is maintained and not exceeded. recommended pressure 90psi.
‰
Keep air hose away from heat, oil and sharp edges. check air hose for wear before each use and ensure that all connections are secure.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
Do Not use tools for tasks that they are not designed to perform.
8
Do Not operate tools if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do Not carry the tool by the hose, or yank the hose from the air supply.
8
Do Not place air line attachments close to your face and do not point at other people or animals.
8
Do Not direct air from the air line at yourself or others.
8
Do Not operate tools unless you have been instructed in their use by a qualified person.
8
Do Not carry tools with your finger on the trigger and avoid unintentional starting.
8
Do Not drop, throw or abuse the tools as they are precision instruments.
8
Do Not leave the tools operating unattended.
8
Do Not get the tools wet or operate in damp or wet locations.
8
Do Not allow tools to free run for an extended period of time as this will shorten their life.
8
2. iNtroDuctioN
comprehensive air tool kit containing: medium stroke air hammer, air die grinder, 1/2" drive air impact wrench and 1/2" drive air ratchet wrench.
includes a selection of Walldrive® sockets, extension bar, grinding points, chisels and many accessories. suitable for workshop and bodyshop
applications. supplied in carry case.
3. speciFicatioN
All tools:
max air consumption: ..........................................................5cfm
operating pressure: ...........................................................90psi
Air inlet size: .................................................................. 1/4"BsP
total weight: ..........................................................................8kg
ratchet wrench 1/2" sq. drive:
maximum torque: ................................................45lb.ft, (61nm)
Vibration: ...................................................................... 3.27m/s²
uncertainty: .................................................................... 1.5m/s²
noise power: .................................................................... 102dB
noise pressure: .................................................................. 91dB
© Jack sealey limited
instructions for
air tool kit 4pc with accessories
model no:
Wear eye
Wear protective
protection
gloves
Original Language Version
sa2004kit.V2
Wear a
mask
impact wrench 1/2" sq.drive:
Working/maximum torque: .......................200/230lb.ft, (312nm)
Vibration: ...................................................................... 5.17m/s²
uncertainty: .................................................................... 1.5m/s²
noise power: .................................................................... 105dB
noise pressure: .................................................................. 94dB
Air die grinder:
chuck size: .......................................................................Ø6mm
free speed: ................................................................ 22000rpm
Vibration: ........................................................................ 1.6m/s²
uncertainty: .................................................................... 0.8m/s²
noise power: .................................................................... 100dB
noise pressure: .................................................................. 89dB
sA2004Kit.V2 | issue 1 17/11/16
Advertisement
Related Manuals for Sealey SA2004KIT.V2
Summary of Contents for Sealey SA2004KIT.V2
- Page 1 Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
-
Page 2: Preparation For Use
4.8. couplings - vibration may cause failure of a quick change coupling that is connected directly to the air tools. 4.8.1. to overcome this, connect a leader hose (sealey model number AH2r) to the tools. Fig.2 4.8.2. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. see figs.1 & 2. -
Page 3: Maintenance
Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty. 9.2. if the air supply does not have an oiler, lubricate the air tool daily with a few drops of sealey air tool oil dripped into the air inlet to prolong its life. - Page 4 01284 757500. environmental protection recycle unwanted materials instead of disposing of them as waste. all tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
- Page 5 warNiNG! – risk of hand arm Vibration injury. this tool may cause hand arm Vibration syndrome if its use is not managed adequately. this tool is subject to the vibration testing section of the machinery directive 2006/42/ec. this tool is to be operated in accordance with these instructions. ratchet wrench: Measured vibration emission value (a): 3.27m/s²...